Fuller® Rear Camera Mirror for Ford
F-150 (2015-Current) & Super Duty
(2017-Current) FVMR-1181
FVMR-1181 FullVUE Rear Camera Mirror
| Recommended Tools | Difficulty Level |
 |
 |
| Install Time | |
 |
Kit Contents
Components for installing the FVMR-1181
Kit Contents:
Fuller® Mirror & Harness
3rd Brake Light Bezel & Camera
9m Camera Harness
Installation of the Fuller Mirror & Wire Connections
If the truck has a forward facing camera in the plastic housing behind the rearview mirror then skip to Part 1b.
| Part 1a | Attaching the Fuller Mirror to the windshield |
| 1. Remove the old mirror from the mount on the windshield as per manufacturer’s directions. Be sure to use the proper removal tool if required. 2. Install new mirror onto the D-tab and tighten with a Phillips screwdriver. Take care not to overtighten. Overtightening could result in damage to your windshield. |
 |
| Part 1b | These steps are for trucks with a forward facing camera in the plastic housing behind the rearview mirror. |
|
Installation of the Fuller Mirror & Wire Connections
| Part 2 | Powering the Fuller Mirror |
| 1. Connect the power harness to the plug on the mirror. Route the harness across the top of the head liner, along the windshield, and down the A-pillar, and to the desired location in the kick panel 2. Ensure that the harness will not be pinched when trim panels are replaced. |
 |
| Part 3 | Wiring the Fuller Mirror |
| 1. Connect the RED wire from the mirror harness to 12-volt accessory power. (PHOTO) Need factory wire color 2. Connect the YELLOW wire from the mirror harness to 12-volt constant power. (PHOTO Need factory wire color 3. Connect the BLACK wire to a solid ground. Chassis ground in the kick panel is recommended. (PHOTO) |
 |
| Part 4 | Function test of the Fuller Mirror |
| 1. Turn the vehicle ignition on and see if you are seeing the front camera displayed on the screen. Turn off the ignition and the mirror will power down |
Disassembly
| Part 1 | Removing the third brake light |
| 1. Use a Phillips screwdriver to remove the screws on either side of the brake light 2. Pull the brake light out from the cab. Be Careful not to damage the foam gasket around the opening. 3. Disconnect the power connector from the light. |
 |
Running Wires
| Part 1 | Video Connector |
| 1. Connect the 9m camera harness to the mirror harness at the connection by the mirror. 2. Run the 9m camera harness from the Fuller Mirror through the headliner toward the brake light. 3. Pull the video connector of the 9m camera harness through the grommet to the outside of the cab. |
 |
Assembly
| Part 1 | Assembling the Bezel |
| 1. Attach the thick foam gasket to the back side of the bezel or to the light. Whichever piece does not have a foam gasket from the factory. Note: The cable for the camera must go through the channel of the bezel before the foam is put overtop 2. Put the foam side of the bezel against the vehicle. 3. Connect the rear camera harness to the camera. Make sure to line up the arrows on the connectors 4. Plug the brake light back into the cab plug 5. Put the screws through the hole of the light and insert the light into the bezel. 6. Use the screws that are showing through the bezel to line up with the screw holes of the vehicle. ( Be careful not to scratch the vehicle.) 7. Screw the assembly back together with the factory screws. |
 |
Adjustment
| 1. If you need to change the camera’s pitch, gently bend the bracket until it reaches the desired view angle. |  |
Vehicle Application:
Ford F-150 (2015-Current) &
Super Duty (2017-Current)
Part Number: FVMR-1181
FullVUE® Rear Camera Mirror – FVMR-1181
Documents / Resources
 |
BRANDMOTION FVMR-1181 FullVUE Rear Camera Mirror [pdf] User Manual FVMR-1181 FullVUE Rear Camera Mirror, FVMR-1181, FullVUE Rear Camera Mirror, Rear Camera Mirror, Camera Mirror, Mirror |
 |
BRANDMOTION FVMR-1181 FullVUE Rear Camera Mirror [pdf] Instruction Manual FVMR-1181 FullVUE Rear Camera Mirror, FVMR-1181, FullVUE Rear Camera Mirror, Rear Camera Mirror, Camera Mirror, Mirror |
