Bose logo

Wave® Music System IV

Music System IV

Owner’s Guide

Important Safety Instructions

Please read this owner’s guide carefully and save it for future reference.
Arrohead SymbolThe lightning flash with an arrowhead symbol within an equilateral triangle alerts the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electrical shock.
The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the user to the presence of important operating and maintenance instructions in this owner’s guide.

WARNINGS:

  • To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture.
  • Do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids, such as vases, on or near the apparatus. As with any electronic products, use care not to spill liquids into any part of the system. Liquids can cause a failure and/or a fire hazard.
  • Keep new and used batteries away from children. Do not ingest battery, chemical burn hazard. The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed it can cause severe internal burns in just 2 hours and can lead to death. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think the battery may have been swallowed or placed inside any part of the body seek immediate medical attention. May explode or cause a fire or chemical burn if incorrectly replaced or mishandled. Do not recharge, disassemble, heat above 212°F (100°C), or incinerate. Replace only with an agency approved (ex. UL) CR2032 or DL2032 3-volt lithium battery.  Dispose of used batteries promptly.
  • Do not place any naked flame sources, such as lighted candles, on or near the apparatus.
  • To prevent electric shock, match the wide blade of the line cord plug to the wide slot of the AC (mains) receptacle. Insert fully.

Symbol WARNING: This product contains magnetic material. Contact your physician if you have questions on whether this might affect the operation of your implantable medical device.

Symbol  WARNING: Contains small parts which may be a choking hazard. Not suitable for children under age 3.

CAUTIONS:

  • Make no modifications to the system or accessories. Unauthorized alterations may compromise the safety, regulatory compliance, and system performance.
  • Long-term exposure to loud music may cause hearing damage. It is best to avoid extreme volume when using headphones, especially for extended periods.
  • Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure from the internal laser component. The compact disc player should not be adjusted or repaired by anyone except properly qualified service personnel.

Notes:

  • The product label is located on the bottom of the product.
  • The product must be used indoors. It is neither designed nor tested for use outdoors, in recreational vehicles, or on boats.
  • Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device shall remain readily operable.

Symbol Please dispose of used batteries properly, following any local regulations. Do not incinerate.

Class 1 laser product
This CD player is classified as a CLASS 1 LASER PRODUCT  according to EN/IEC 60825. The CLASS 1 LASER PRODUCT label is located at the bottom of the unit.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

Important Safety Instructions

  1. Read these instructions.
  2. Keep these instructions.
  3. Heed all warnings.
  4. Follow all instructions.
  5. Do not use this apparatus near water.
  6. Clean only with a dry cloth.
  7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
  8. Do not install near any heat sources, such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
  9. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
  10. Only use attachments/accessories specified by the manufacturer.
  11. cart, standUse only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
  12. Unplug this apparatus during lightning storms or when unused for long periods of time.
  13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way: such as power supply cord or plug is damaged; liquid has been spilled or objects have fallen into the apparatus; the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Regulatory Information

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment to an outlet on a different circuit than the one to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by Bose Corporation could void the user’s authority to operate this e quipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003. CAN ICES-3(B)/ NMB-3(B)
This device complies with FCC and Industry Canada RF radiation exposure limits set forth for general population. It must not be colocated or be operating in conjunction with any other antennas or transmitters.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This equipment should be installed and operated with a minimum distance of 8 in. (20 cm) between this device and your body.

Product data logger
This system features a product data logger that is designed to help Bose better understand product usage and performance over time. The product data logger records certain technical data and usage history, including but not limited to volume levels, on/off data, user settings, source inputs, power output, and setup data. We may use this data to provide you with better service and support on your system and to improve product design in the future. Special equipment is required to read the data stored by the product data logger and such data can only be retrieved by Bose if your system is returned to Bose for service or as returned merchandise. The product data logger does not collect any personally identifiable information about you and does not record title, genre or other information about the media content you access while using your system.

Please complete and retain for your records
Record the serial number of your new Wave® Music System IV in the space below. The serial and model numbers can be found on the bottom panel.
Serial number: _____________________________________________
Model number: ____________________________________________
Purchase date: _____________________________________________
We suggest you keep your receipt with this owner’s guide.

Date of manufacture: The four bolded digits in the serial number indicate the date of manufacture. The first digit is the year of manufacture; “5” is 2005 or 2015. Digits 2-4 are the month and date; “001” is January 1 and “365” is December 31.
China Importer: Bose Electronics (Shanghai) Company Limited, Part C, Plan 9, No. 353 North Riying Road, China (Shanghai) Pilot Free Trade Zone

EU Importer: Bose GP, Castleblayney Road, Carrickmacross, Ireland

Taiwan Importer: Bose Taiwan Branch, Room 905, 9F, Worldwide House, 131 Min Sheng East Rd, Section 3, Taipei, Taiwan, 105

The distinctive design of the Wave music system is a registered trademark of Bose Corporation in the U.S. and other countries.
©2015 Bose Corporation. No part of this work may be reproduced, modified, distributed or otherwise used without prior written permission.

Introduction

About your Wave® Music System IV 

Your Wave® Music System IV provides an elegant way to bring high-quality sound into any room.

System Features

  • Display provides access to system settings and information.
  • AUX connector enables playback from an audio device.
  • Headphone connector for private listening.
  • FM/AM tuner delivers precise radio reception.
  • CD drive provides access to even more music.
  • Remote control for point-and-click control from up to 20 feet away.

The demonstration CD
We encourage you to listen to the demonstration music CD included in the carton. Simply insert the demonstration disc and your Wave® Music System IV will play the CD automatically. For more details, see
“Playing audio CDs” on page 9.

The demonstration CD

The benefits of research
Over fourteen years of research by Bose Corporation brings you the benefits of award-winning proprietary acoustic waveguide speaker technology. Using this technology, a tube efficiently transfers energy from a small speaker to the outside air over a wide range of low frequencies. And, long waveguides, folded into intricate patterns, fit into products small enough to be placed comfortably in your home. Your Wave® Music System IV features dual tapered waveguide speaker technology, connecting two speakers to two 26″ tapered waveguides which combine to deliver performance well beyond the size of the system.

Dual tapered waveguides

Unpacking
Carefully unpack the carton and confirm that the following parts are included.

Wave ® music system IVRemote control (battery installed)Demonstration CDAC power cord(s)

Symbol May ship with multiple power cords. Use the power cord for your region.
Note: If part of the system is damaged, do not use it. Contact your authorized Bose® dealer or Bose customer service. Refer to the quick start guide in the carton for contact information.
Save the carton and packing materials for transporting or storing the system.

Setting Up the System

Placing the system

  • To enjoy maximum audio performance:
    — Place the system across the room from where you listen.
    — Place the system within two feet of a wall, and avoid placing directly in a corner.
  • Place the system on a flat, stable surface.

CAUTIONS:
• Do not place the system on a metal surface. It could interfere with AM reception.
• Do not place the system on a heat-sensitive surface. Like all electrical equipment, it generates some heat.
• Do not use the system in a damp location or any other place where moisture can get inside.

Connecting to power
1. Insert the small end of the power cord into the AC POWER connector.
2. Plug the power cord into an AC (mains) power outlet.

Connecting to power

Setting the clock
After plugging in the system, set the clock using the remote.
1. Press and hold either Time – or Time + for about one second.
Note: Press-and-hold operations require holding the button down for about one second.

CLOCK SET

Initially, HOLD TO SET appears on the display and then quickly changes to – CLOCK SET – as the button is depressed.

2. Release the selected Time button.
3. Press Time – to adjust the displayed time backward or press Time + to adjust the displayed time forward until it matches the current time. You can also press and hold for rapid adjustment.
4. Wait five seconds for the system to exit clock setup mode.
Notes:
• To change the clock from 12-hour (AM/PM) time to 24-hour time, see “Changing a system setting” on page 13.
• If the system loses power due to a power outage or if you unplug the system, all system settings are permanently retained. However, the clock time is only temporarily stored in backup memory for up to 48 hours.

Using the System

Remote control buttons

Use the remote control to operate the system. Aim the remote at the display and press the buttons. The remote works within 20 feet of the display.

Remote control buttons

Touch pad

The system has a touch-sensitive control pad on the top panel. Momentarily placing your hand on the touch pad can power on or off the system, snooze a sounding alarm, and reset it for the next day (see page 11).

ouch-sensitive control pad

Notes:
• Press-and-hold operations require holding the button down for about one second.
• Pressing Symbol,Symbol  or Symbol automatically powers on the system to the selected source.

Reading the display

Reading the display

Powering on or off the system

• Press Power on the remote control
or
• Touch the touch pad. ouch-sensitive control pad

The last source you were listening to is active.

Alternatively:
Press any source button to power Symbol, Symbol  Symbol the system on to that source.

Notes:

  • Selecting AUX does not power on a device connected to AUX IN (such as a media player). Power on the device first.
  • After 24 hours of no button presses, the system switches to standby (off). If the 20-minute system standby timer (page 14) is enabled, the system switches to standby if no audio is played and no buttons are pressed for 20 minutes.

Controlling the volume

Symbol Press and hold Symbol or Symbol to adjust the volume level.
Symbol VOLUME – 0 (silent) to 99 (loud) appears on the display to indicate the level.

Symbol Press to mute the system. Press again, or press Symbol to unmute.
While muted, you can press Symbolto lower the volume before unmuting the system.
Note: When the system is off, the volume can only be adjusted between 10 and 75.

Setting the Sleep timer

Symbol Press SLEEP to set the system to shut off after a selected period of time.

  • After pressing SLEEP, SLEEP – 30 MIN (or your last setting) appears on the display and the sleep timer begins counting down. If the system is off, press SLEEP to power on and immediately set the sleep time. The last source selected will start playing as the sleep timer counts down.
  • While the SLEEP setting is displayed, press SLEEP again to set the sleep timer to 10-90 minutes (in 10-minute increments) or OFF.

Note: If more than 10 seconds elapses between button presses, the system automatically exits the sleep timer setup mode.

  • To review the remaining sleep time, press SLEEP.
  • To cancel the sleep timer, press and release SLEEP until SLEEP – OFF appears on the display.

Listening to Other Sources

Listening to FM or AM radio

SymbolPress RADIO to turn it on to the station last selected. Press RADIO as necessary to select FM or AM radio.

When you select FM radio, Radio Data System (RDS) information for the current station is displayed. This is controlled by the RADIO TEXT setting in the setup menu. To disable RDS and view only the station frequency, change the RADIO TEXT setting to OFF. See  “Changing a system setting” on page 14.

controlled by the RADIO TEXT

Tuning to an FM/AM station

When you press RADIO, Seek/Track, or Tune/MP3 to tune to a radio station, the frequency appears in the center of the display while you are tuning.

Tuning to an FM/AM station • When playing an audio CD, source information is displayed: Selected source Clock time When you press RADIO, Seek/Track, or

Tuning to an FM/AM station • When playing an audio CD, source information is displayed: Selected source Clock time When you press RADIO, Seek/Track, or

Note: If AM reception is weak, rotate the system clockwise or counterclockwise to improve AM reception. If FM reception is weak, make sure the power cord is straightened as much as possible. To improve FM reception, you can install an external FM antenna (see page 13).

Storing FM/AM radio station Presets

You can store up to six FM and six AM radio stations for quick recall using the Presets buttons. Storing a preset replaces any station previously stored to that preset number.preset number

  1. Tune to the station you want to save as a preset.
  2. Press and hold one of the six PRESETS buttons until you hear a double tone and the preset number and station frequency appear on the display.
  3.  Press one of the PRESETS buttons to quickly tune to a previously stored FM or AM station.

Improving FM reception

Unwind and straighten the power cord to ensure the best FM radio reception. The power cord is used as an antenna.

Playing audio CDs

Insert the disc, label side up, into the CD slot below the display. The disc player pulls the disc in and begins playing.

Press Symbol if the CD source is not selected.

CD

  • When playing an audio CD, source information is displayed:

source information is displayed

source information is displayed

Notes:

  • When you play a stopped CD it will always resume from the place it was stopped.
  • If you eject a CD but do not remove it from the CD player slot within 10 seconds, the CD player will pull the CD back into the player and reload it.

CAUTION: DO NOT INSERT mini CDs or non-circular CDs into the disc player. These discs may not play properly and could interfere with the system’s ability to eject them.

Listening to Other Sources

Playing MP3 CDs

The system can play MP3 music files recorded on CD-R and CD-RW discs. To play, pause, stop or eject an MP3 CD, use the same remote control buttons as for an audio CD.
You can easily navigate through your music files using the Tune/MP3 and Seek/Track remote control buttons.

emote control buttons

When navigating an MP3 CD, folder number and track number are displayed:

track number are displayed

Note: The Root level is displayed as folder number 00.

Once the track begins playing, artist name, song title, and elapsed track time will return to the display:

rack begins playing, artist name

Notes:

  • The system will display artist name and song title information when available on music file CDs.
  • The audio quality of MP3 CDs is dependent on factors such as the encoded bit rate, the sampling rate, and the type of encoder used. The system supports MP3 CDs encoded at bit rates of 64kbps or higher, and sampling rates of 32kHz or higher. It is recommended that a bit rate of at least 128kbps and a sampling rate of 44.1kHz or better be used.
  • Playback quality of recorded CD-R and CD-RW discs is dependent on the CD recording process and software used to record the disc. An improperly  recorded audio CD may cause the system to exhibit unexpected behavior.

CD Play Modes

 ‍Symbol While a CD is playing, you can change the way it is played. Press Play Mode repeatedly until the play mode you want is displayed:

CD Play Modes

Note: The play mode will return to NORMAL PLAY whenever a CD is inserted.

Setting and Using the Alarms

Alarm buttons and indicators

The system has two alarms, Alarm 1 and Alarm 2.
Each alarm can be set for:

  • Time
  • Volume
  • Wake-up source: buzzer, radio, or CD

Using the Alarm buttons
Using the Alarm buttons on the bottom of the remote you can setup and operate each alarm:
Press to turn

Using the Alarm buttons

Alarm status indicators

The upper right-hand corner of the display shows the alarm status indicators if the alarm is set.
Example with Alarm 1 and 2 set:

Alarm status indicators

Setting the alarms

You can choose the settings for each alarm by activating the Alarm Setup mode and displaying the settings for each alarm.
To setup Alarm 1 or 2:
1. Press Alarm Setup Symbol.
The alarm number and time start flashing (A) and after a moment, the current Alarm 1 settings are displayed (B).

Alarm SetupAlarm Setup
The alarm you set is turned on and the alarm time displays:

alarm time displays

Using the alarms

Turning an alarm on or off

Press  Symbol to turn the selected alarm on or off.
When an alarm is turned on, the alarm number and time appear in the upper right corner of the display.

alarm is turned on

Snoozing an alarm

Tap the touch pad ,   or press on the remote.

SNOOZE is displayed for the duration of the selected snooze time and then the alarm sounds again.

alarm

The snooze time is set at the factory to 10 minutes. To change the snooze time, see page 14.
Stop and reset a sounding alarm
Press Symbol
Reset a snoozed alarm for the next day
After snoozing the alarm, place your hand on the touch pad again and hold it there for at least 2 seconds, or press Stop Alarm.

Connecting Other Equipment

System connections

The rear panel of the system provides connections for external equipment.

System connections

System connections

Using the AUX IN connector

When using a TV, DVD player, computer, video game or other audio source, you can enhance your listening experience by playing the audio device through the system.
Connecting an audio device to the system requires one of the following cables:

 audio cableRCA cable

To obtain the correct cable, contact Bose® customer service or visit a local electronics store. Refer to the quick start guide in the carton.
Using a cable to connect an audio device
1. Using a cable, connect your audio device to the AUX IN connector on the system’s connector panel.

Using a cable to connect an audio device

2. Press Symbol on the remote control. The last source you were listening to is active.
3. Press and release Symbol until appears on the display.
4. Start playing music on the audio device.
5. Press and hold Symbol to adjust the volume.
Note: If the volume level of the system cannot be adjusted high enough, increase the volume level of the connected audio device.

Using headphones

For private listening, plug the headphones into the headphone connector on the rear panel of the system.

headphones

CAUTION: Long-term exposure to loud music may cause hearing damage. It is best to avoid extreme volume when using headphones, especially for extended periods.
Notes:

  • Plugging in headphones automatically mutes the speakers. Because headphone volume levels may vary from speaker volume levels, be sure to lower the volume of the system before connecting or disconnecting headphones.
  • While using headphones, alarms will be heard through the system speakers.

Controlling the headphones volume:
Press and hold Symbol to adjust the listening level of your headphones.

Using an external antenna

The system power cord is used as an antenna for FM radio. If, after adjusting the position of the power cord, you still experience poor reception, you may need to install an external antenna. An external dipole antenna can be ordered through Bose Customer Service. Refer to the quick start guide in the carton.

  1.  Insert the 3.5 mm plug of the FM antenna into the FM ANTENNA connector.
  2. Extend the ends of the antenna as far from the unit and other external equipment as possible to establish optimum reception.

FM antenna connector

Note: Many FM radio stations transmit a vertically polarized signal as well as, or instead of, a horizontally polarized signal. If the horizontal antenna orientation does not provide good reception, try hanging the antenna in a vertical orientation.

Personalizing the System

The setup menu

The setup menu allows you to customize the operation of the system.

Personalizing the System

Changing a system setting

Changing a system setting

Care and Maintenance

Troubleshooting

Care and Maintenance

Care and Maintenance

Replacing the remote control battery

Place the remote face down on a flat surface.
1. Using your finger, push the tab lock to the side as shown and hold. Slide the battery compartment open.

Replacing the remote control battery

2. Remove the old battery and install the new one with the plus
(+) symbol facing up.

 Remove the old battery and install

 

3. Gently slide the battery compartment closed. It locks automatically.
WARNING: Keep new and used batteries away from children. Do not ingest battery, chemical burn hazard. The remote control supplied with this product  ontains a coin/button cell battery. If the coin/button cell battery is swallowed it can cause severe internal burns in just two hours and can lead to death. If the  battery compartment does not close securely, stop using the product and keep it away from children. If you think the battery may have been swallowed or placed inside any part of the body, seek immediate medical attention. The coin/button cell battery may explode or cause a fire or chemical burn if incorrectly replaced or mishandled. Do not recharge, disassemble, heat above 212ºF (100ºC), or incinerate. Replace only with an agency approved (ex. UL) CR2032 or DL2032 3-volt lithium battery. Dispose of used batteries promptly.

Cleaning

Clean the surface of the system with a soft, dry cloth.

  • Do not use any sprays near the system. Do not use any solvents, chemicals, or cleaning solutions containing alcohol, ammonia or abrasives.
  • Do not allow liquids to spill into any openings.

Customer service

For additional help, contact Bose Customer Service. Refer to the quick start guide in the carton.

Limited warranty

Your system is covered by a limited warranty. Details of the limited warranty are provided on the quick start guide in the carton.

Please refer to the quick start guide for instructions on how to register. Failure to register will not affect your limited warranty rights.
The warranty information provided with this product does not apply in Australia and New Zealand. See our website at www.bose.com.au/warranty or  www.bose.co.nz/warranty for details of the Australia and New Zealand warranty. Technical information AC power rating 120V Symbol 60Hz 60W max.

Bose Wave Music System IV User Manual – Optimized PDF
Bose Wave Music System IV User Manual – Original PDF

Join the Conversation

3 Comments

Leave a comment

Your email address will not be published.