MIC-770 V3 12th/13th Gen Intel® Core™ i Socket Compact Fanless Computer Startup Manual

Packing List

• MIC-770 V3 bare-bone system x 1
• Startup Manual EN\CN\TC for MIC-770 V3 3rd Ed. P/N: 2041077052
• 4-pin Phoenix connector P/N: 1652003234
• Mounting bracket x 2 P/N: 1960070543T00A
• SATA cable x 1 P/N: 1700013095-01
• SATA power cable x 1 P/N: 1700024372-01

If any of these items are missing or damaged, please contact your distributor or sales representative immediately.

Notes

Acrobat Reader is required to view any PDF file. Acrobat Reader can be downloaded at: get.adobe.com/reader (Acrobat is a trademark of Adobe).

For more information on this and other Advantech products, please visit our website at: http://www.advantech.com

For technical support and service, please visit our support website for MIC-770 V3 at: https://advt.ch/mic770spt

Register your products on our website and get 2 months extra warranty for free at: http://www.register.advantech.com

Part No. 2041077052 Printed in China 3rd Edition March 2024

CAUTION: THERE IS DANGER OF EXPLOSION IF THE BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.

ATTENTION: DANGER D'EXPLOSION SI LA BATTERIE EST INEXACTEMENT REMPLACÉE. REMPLACEZ SEULEMENT AVEC LA MÊME CHOSE OU LE TYPE ÉQUIVALENT RECOMMANDÉ PAR LE FABRICANT, JETTENT LES BATTERIES UTILISÉES INSTRUCTIONS DE S SELON FABRICANT DES'.

Specifications

Processor System

• 12th/13th Gen Intel® Core™ i socket CPU (LGA1700)

Memory

• Supports dual-channel DDR5 SODIMM-4800 MHz, 32GB per slot with ECC function (W SKU only); Max. capacity is 64GB.

Graphics

• R680E: Intel® HD Graphics 770, supports DirectX 12
• H610E: Intel® HD Graphics 770, supports DirectX 12

Serial Ports

• 2 x RS-232/422/485, RS-485 supports automatic flow control

Ethernet

• Interface: 10/100/1000 Mbps
• Controllers: R680E LAN1: Intel® I219LM, LAN2: Intel® i210IT; H610E LAN1: Intel® I219V, LAN2: Intel® i210IT

Storage

• Internal 2.5" Storage Bay: 1
• mSATA: 1
• NVMe (M.2): 1 x M-Key 2280 with PCIe Gen 3 x4. Use the wide-temperature NVMe module without the heatsink. (R680E SKU, operating temp. -10~50°C)

Front I/O

• Display: 1 x VGA, 1 x HDMI
• USB: R680E: 2 x USB 3.2 (Gen.2), 6 x USB 3.2 (Gen.1); H610E: 4 x USB 3.2 (Gen.2), 4 x USB 2.0
• Serial: 2 x RS-232/422/485
• Audio: Line-out/Mic-in

Power Requirements

• Power type: ATX/AT
• Power input Voltage: 9-36 VDC
• Minimum Power Input: 9VDC 16A - 36VDC 5A

This product is intended to be supplied by a UL-certified power supply or UL-certified DC source rated 19Vdc, 7.89A minimum, TMA 50°C minimum (Safety certificate operation temperature=40°C). For assistance, contact Advantech.

Miscellaneous

• Power Switch (Orange: System standby / Green: System Power boot)
• COM1 TX & RX LED; COM2 TX & RX LED; Storage Status LED (Blinking: read/write; Dark: no behavior)

Environment

• Operating Temperature: TDP 35W CPU: -20 ~ 60°C; TDP 65W CPU: -20 ~ 50°C. Note: Safety Certification Test Temperature: safety max 60°C with SSD (TDP 35W CPU) (Safety certificate operating temperature 60°C)
• Storage Temperature: -40 ~ 85°C (-40 ~ 185°F)
• Relative Humidity: 95% @ 40°C (non-condensing)

Physical Characteristics

• Dimensions (W x H x D): 77 x 192 x 230 mm
• Weight: 2.8 kg (6.17 lb)

Jumpers and Connectors

Jumpers can be set to suit your application. The table below shows the function of each of the jumpers and connectors.

Connectors

AT Module / ATX Module Selection

PSON1: System AT/ATX Module Selection

Battery

The computer is supplied with a battery-powered realtime clock circuit. There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.

Declaration of Conformity

This device complies with the requirements in Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.

System I/O Interface

The system provides various I/O connections:

• COM1/2: TX for COM1, RX for COM1, TX for COM2, RX for COM2
• USB: USB3.2/2.0 ports
• Storage: SATA interface
• LAN: LAN2/LAN1 ports
• Display: COM1/2, VGA
• Power: Power input
• Ground: Chassis GND
• Audio: Line out, MIC in
• Expansion: USB3.2, iDoor, Flex I/O interface
• Display: HDMI
• Power Input: 9-36 VDC

Simple Maintenance Process

Memory Installation

MIC-770 V3 supports DDR5 SODIMM ECC/non-ECC type memory modules. For a detailed memory support list, contact your distributor or sales representative.

1. Undo 4 screws and remove the bottom cover.
2. Undo 7 screws to remove the memory thermal cover.
3. Install the memory module and affix the thermal pad (P/N: 1990019498N000).
4. Ensure the thermal pad and memory thermal cover are fully affixed and compacted.

Mini-PCIe/mSATA Installation

MIC-770 V3 supports full-size Mini-PCIe /mSATA.

1. Undo 4 screws and remove the bottom cover.
2. Install the module in the Mini-PCIe socket and secure with screws.
3. Replace the bottom cover and secure with screws.

Storage Installation

1. Undo 4 screws and remove the bottom cover.
2. Undo 4 screws to remove the storage tray.
3. Secure the storage device onto the HDD tray with 4 screws (P/N:1930002235).
4. Assemble the SATA cable and SATA power cable, and replace the storage tray securely with 4 screws.
5. Replace the bottom cover.

NVMe M.2 Installation

MIC-770 V3 (R680E SKU) supports NVMe M.2.

1. Undo 4 screws and remove the bottom cover.
2. Undo 7 screws to remove the cover, thermal cover, and M.2 cover.
3. Install the NVMe M.2 module in the M.2 socket and secure with screws.
4. Replace the bottom cover and secure with screws.

Internal USB 2.0 Installation

1. Undo 4 screws and remove the bottom cover.
2. Loosen the bracket screw and adjust the bracket size in accordance with the USB dongle size.
3. Install the USB dongle in the first socket (only the first socket is functional).
4. Secure the bracket screw, replace the bottom cover, and secure with screws.

CPU Installation

1. Undo 4 screws and remove the bottom cover.
2. Undo 4 screws to remove the storage tray.
3. Undo 7 screws to remove the memory & M.2 thermal cover.
4. Undo 4 screws in the corner of the chassis.
5. Undo 4 screws around the CPU to release the CPU heatsink.
6. Remove the CPU heatsink and install the new CPU.
7. Smear thermal grease onto the CPU.
8. Replace the CPU heatsink, memory, and the M.2 thermal cover, storage tray, and bottom cover.

Mounting Kit Installation

1. Take the mounting kit from the accessory box.
2. Secure with 4 screws (P/N: 1930007259-01, M4x4L F/S D=8.5 H=1.5 (2+) ST/H BZn-NK) and install the system on a table.

Safety Instructions

1. Read these safety instructions carefully.
2. Keep this startup manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to a power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the power cord.
10. Note all cautions and warnings on the equipment.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service personnel:
    • The power cord or plug is damaged.
    • Liquid has penetrated into the equipment.
    • The equipment has been exposed to moisture.
    • The equipment does not work well, or you cannot get it to work according to the user manual.
    • The equipment has been dropped and damaged.
    • The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -40°C (-40°F) OR ABOVE 85°C (185°F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: THERE IS DANGER OF EXPLOSION IF THE BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
17. The sound pressure level at the operator's position according to IEC 704-1:1982 should be no more than 70 dB (A).
18. RESTRICTED ACCESS AREA: The equipment should only be installed in a Restricted Access Area.
19. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.

I/O Connectors Overview

The system features a comprehensive set of I/O connectors, including:

• USB 2.0 ports
• SATA connectors
• SPI_TPM1 (top port only)
• NVMe M.2 slot
• CPU socket
• DIMM slots (DIMMB, DIMMA)
• SATA Power connector
• Mini-PCIe slots (MPCIE1, MPCIE2/MSATA)
• Power Switch connector (PSON1)
• COM ports (COM, COM 5&6, COM 3&4)
• Display Ports (DP1, DP2)
• GPIO connectors (GPIO 1&2)

* Refer to the user manual for eFuse (SW5) behavior.

System Dimensions

The physical dimensions of the MIC-770 V3 are:

Width (W) x Height (H) x Depth (D): 77 mm x 192 mm x 230 mm.

Available Models

The MIC-770 V3 series includes various models, such as:

MIC-770V3W Series: MIC-770V3W-00A1, MIC-770V3W-01A1, MIC-770V3W-02A1, MIC-770V3W-03A1, MIC-770V3W-04A1, MIC-770V3W-05A1, MIC-770V3W-06A1, MIC-770V3W-00A2, MIC-770V3W-01A2, MIC-770V3W-02A2, MIC-770V3W-03A2, MIC-770V3W-04A2, MIC-770V3W-10A1, MIC-770V3W-11A1, MIC-770V3W-12A1, MIC-770V3W-13A1, MIC-770V3W-14A1, MIC-770V3W-10A2, MIC-770V3W-11A2, MIC-770V3W-12A2, MIC-770V3W-13A2, MIC-770V3W-14A2, MIC-770V3W-20A1, MIC-770V3W-21A1, MIC-770V3W-22A1, MIC-770V3W-23A1, MIC-770V3W-24A1, MIC-770V3W-20A2, MIC-770V3W-21A2, MIC-770V3W-22A2, MIC-770V3W-23A2, MIC-770V3W-24A2, MIC770V3WBM01-T, MIC770V3WBM02-T, MIC770V3WBM03-T, MIC770V3WBM04-T, MIC770V3WBM05-T.

MIC-770V3H Series: MIC-770V3H-00A1, MIC-770V3H-01A1, MIC-770V3H-02A1, MIC-770V3H-03A1, MIC-770V3H-04A1, MIC-770V3H-05A1, MIC-770V3H-06A1, MIC-770V3H-00A2, MIC-770V3H-01A2, MIC-770V3H-02A2, MIC-770V3H-03A2, MIC-770V3H-04A2, MIC-770V3H-00A3, IC-770V3H-02A3, MIC-770V3H-03A3, MIC-770V3H-04A3, MIC-770V3H-10A1, MIC-770V3H-11A1, MIC-770V3H-12A1, MIC-770V3H-13A1, MIC-770V3H-14A1, MIC-770V3H-10A2, MIC-770V3H-11A2, MIC-770V3H-12A2, MIC-770V3H-13A2, MIC-770V3H-14A2, MIC-770V3H-20A1, MIC-770V3H-21A1, MIC-770V3H-22A1, MIC-770V3H-23A1, MIC-770V3H-24A1, MIC-770V3H-20A2, MIC-770V3H-21A2, MIC-770V3H-22A2, MIC-770V3H-23A2, MIC-770V3H-24A2, MIC770V3HBM01-T, MIC770V3HBM02-T, MIC770V3HBM03-T, MIC770V3HBM04-T, MIC770V3HBM05-T.

RoHS Compliance

The following table indicates the presence of restricted substances in the equipment:

Note 1: "Exceeding 0.1 wt %" and "exceeding 0.01 wt %" indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence.

Note 2: " " indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.

Note 3: " - " indicates that the restricted substance corresponds to the exemption.

Note 4: 0.1 wt % 0.01 wt %

Note 5: 26 20 1 02-27927818