ভূমিকা
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Ikea KALLROR 503.570.02 Stainless Steel Cabinet Handles. Please read these instructions carefully before proceeding with installation to ensure proper and safe use.
পণ্য ওভারview
The Ikea KALLROR 503.570.02 handles are designed to offer a modern aesthetic and functional grip for your kitchen cabinets or drawers. This set includes two handles and all necessary screws for a complete installation.
This image displays two sleek, cylindrical stainless steel cabinet handles, along with four silver screws. The handles have a brushed finish, and each handle is shown with two mounting posts. The screws are designed to secure the handles to cabinet doors or drawers.
স্পেসিফিকেশন
| মডেল নম্বর | 503.570.02 |
| ব্র্যান্ড | আইকেএ |
| Quantity per set | 2টি হ্যান্ডেল |
| হ্যান্ডেল দৈর্ঘ্য | 213 মিমি |
| হ্যান্ডেল ডেপথ | 38 মিমি |
| Hole Spacing (center-to-center) | 160 মিমি |
| Drilled Hole Diameter | 5 মিমি |
| উপযুক্ত দরজা বেধ | 16 মিমি থেকে 21 মিমি |
| Handle/End Cap Material | স্টেইনলেস স্টীল |
| Plastic Parts Material | পলিথিন প্লাস্টিক |
| অন্তর্ভুক্ত উপাদান | ইনস্টলেশন হার্ডওয়্যার (স্ক্রু) |
| ওজন | 170 গ্রাম |
সেটআপ এবং ইনস্টলেশন
Installing your Ikea KALLROR cabinet handles is a straightforward process. Follow these steps carefully for a secure attachment.
প্রয়োজনীয় টুলস
- ড্রিল
- Drill bit (5 mm diameter)
- পরিমাপ টেপ বা শাসক
- পেন্সিল
- স্ক্রু ড্রাইভার (ফিলিপস হেড সুপারিশকৃত)
ইনস্টলেশন পদক্ষেপ
- পরিমাপ এবং চিহ্নিতকরণ: Carefully measure and mark the desired position for the handle on your cabinet door or drawer front. Ensure the marks for the two screw holes are precisely 160 mm apart (center-to-center).
- ড্রিল গর্ত: Using a 5 mm drill bit, carefully drill through the cabinet door or drawer front at the marked positions. Ensure the holes are straight and clean.
- হ্যান্ডেল সংযুক্ত করুন: Align the handle with the drilled holes. Insert the provided screws from the inside of the cabinet door or drawer through the drilled holes and into the handle posts.
- নিরাপদ হ্যান্ডেল: Tighten the screws firmly with a screwdriver until the handle is securely attached. অতিরিক্ত টাইট করবেন না, as this may damage the cabinet material.
- পুনরাবৃত্তি: Repeat the process for the second handle if installing a set.
Important: These handles are suitable for door thicknesses between 16 mm and 21 mm. Verify your cabinet door thickness before drilling.
অপারেশন
The Ikea KALLROR cabinet handles are designed for simple and reliable operation. Grasp the handle firmly to open or close cabinet doors and drawers as needed.
রক্ষণাবেক্ষণ
To ensure the longevity and appearance of your stainless steel handles, follow these maintenance guidelines:
- পরিষ্কার করা: নরম, ঘ দিয়ে নিয়মিত মুছুনamp cloth. For stubborn marks, use a mild detergent solution. Avoid abrasive cleaners, scouring pads, or chemical solvents, as these can damage the stainless steel finish.
- শুকানো: Always dry the handles thoroughly after cleaning to prevent water spots and maintain their luster.
- পরিদর্শন: Periodically check the screws for tightness. If a handle feels loose, gently tighten the screws with a screwdriver.
সমস্যা সমাধান
হাতলটি আলগা
If the handle feels loose, gently tighten the screws from the inside of the cabinet door or drawer. Ensure not to overtighten.
ইনস্টল করার অসুবিধা
Ensure the drilled holes are precisely 160 mm apart (center-to-center) and that the drill bit used was 5 mm in diameter. Verify your cabinet door thickness is within the specified 16-21 mm range.
সমর্থন
For further assistance or inquiries regarding your Ikea KALLROR cabinet handles, please refer to the official Ikea website or contact Ikea customer service directly.
