BN-LINK CP-DB01-1-1 Wireless Remote Control Doorbell

Product Information:

Specifications

• Model: 65X70
• Product Number: CP-DB01-1-1
• Type: Wireless Remote Control Doorbell
• Website: www.bn-link.com

PACKAGE CONTENTS

Included items may vary by kit.

Note: The ring button in this kit is already pre-paired with the receiver for immediate use

PRODUCT VIEW

AC Powered Receiver

1. Function Button
2. Volume Control
3. Music Control
4. LED Light
5. Plug
6. Speaker

PRE-INSTALLTION TIPS

1. Follow the manufacturer’s recommendations when using tools, and wear appropriate protective gear (e.g., safety goggles).
2. Before drilling into walls, check for hidden cables or pipes to avoid damaging them. If unsure, use a cable/pipe detector.
3. Do not install the ring button on a metal door, as it may obstruct signal transmission.
4. Remove the battery insulation strip from the ring button before use. (As picture ®)
5. Ensure the installation area is clean. Wipe the surface with a clean cloth. Note that adhesive stickers may not stick well to dirty or uneven surfaces. Prolonged exposure to sunlight or rain may also affect adhesion.

INSTALLATION

Choose a Location: Select a spot away from heat sources or removing objects (e.g., doors). For locations that do not require fixing, choose a place where the receiver can be easily seen and heard.

1. Doorbell Installation: Plug in the receiver. Insert the receiver into a standard power outlet indoors.
2. Ring Button Installation:
   • Before installation, test the operating range at the selected location and set the ringtone (if needed).
   • Before drilling, ensure there are no cables or pipes in the wall. A drill and a Phillips screwdriver are required for installation.
     1. Use a screwdriver to open the ring button and separate the front cover from the back cover. Secure the back cover to the wall at an appropriate height using two screws through the reserved holes.
     2. Alternatively, use double-sided tape to attach the ring button to the wall. 0-0

If vou do not plan to fix the ring button to the wall. place it in vour desired location.

OPERATION

1. Receiver Pairing Power on the receiver and pair it by pressing the function button and ring button simultaneously after the beep.
2. Adjust the Volume Short press the volume control button to adjust the volume from low to high, with four levels in total.
3. Change the Tone Short press the music control button to cycle through 58 classic Eastern and Western chimes.
4. Mute& Reset
   • Short press the function button to switch between normal and silent modes.
   • Press and hold the function button for 10 seconds until you hear the second beep, then release it to indicate successful code clearing, all settings will return to factory defaults.

CHIMES LIST

RING BUTTON BATTERY REPLACEMENT
Open the battery cover and insert a CR2032 battery.

Note: The CR2032 is a button cell battery. Please take note of the following WARNING.

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery
• DEATH or serious injury can occur if ingested
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• keep new and used batteries out of reach of children.

SPECTEICATIONS

TROUBLESHOOTING

Problem: If the receiver is not working

Potential Cause & Solutions:

• The receiver may be out of range; try placing it in a different location.
• Check all batteries and replace them if necessary. Ensure the LED on the ring button lights up properly when activated.
• Verify that the receiver is not in silent mode and that the ring button is successfully paired with the receiver

Problem: If the signal range is reduced

Potential Cause &Solutions:

• Metal structures, including uPVC door frames, may reduce the signal range. Avoid installing the receiver or button on or near metal surfaces.
• Move the receiver closer to the button.
• Low battery power can reduce the signal range.
• In cold conditions (below 5°C), the batteries may need to be replaced more frequently.

WARRANTY

• 30-Day Money-Back Guarantee: If you are not satisfied with your purchase, you can request a refund within 30 days.
• 12-Month Warranty: The device must have been used under proper technical conditions. Covers failures and defects not caused by human error.

Scan the QR code to activate your warranty and enjoy full customer support

CONTACT US
FOR ANY PROBLEMS DURING USE PLEASE CONTACT US AT support@bn-link.com

Contact Information
For any questions or assistance, contact customer support through the provided channels.

Chimes List
A list of available chimes can be found in the user manual or on the product website.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement
The device has been evaluate to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Documents / Resources

BN-LINK CP-DB01-1-1 Wireless Remote Control Doorbell [pdf] User Guide ESM241U, CP-DB01-1-1, CP-DB01-1-1 Wireless Remote Control Doorbell, CP-DB01-1-1, Wireless Remote Control Doorbell, Remote Control Doorbell, Control Doorbell

References

• User Manual