Static Route Setup

„

Информация за продукта

Спецификации

• Static Route Setup
• Supports RIP (Routing Information Protocol)
• LAN TCP/IP and DHCP Setup

Инструкции за употреба на продукта

Static Route Setup

If you have multiple private subnets behind the router or need
to access another public subnet via an inside router, you can
configure the router to route IP packets using the LAN TCP/IP and
DHCP Setup page.

Конфигурация

1. Add a static route to the inside public subnet 211.100.88.0/28
   via 192.168.1.3/24.
2. Note: Add a static route in the router 192.168.1.3/24 to route
   IP packets to 192.168.1.0/24 and 192.168.10.0/24 subnets via the
   router 192.168.1.1/24.
3. Click Static Route Setup > View Routing Table to verify the
   current routing table.

Delete or Deactivate a Static Route

1. Click Static Route Setup > Index Number you want to
   изтрий.
2. Select Status/Action to Empty/Clear.
3. Click OK button to delete the route.

ЧЗВ

Q: What is the purpose of Static Route Setup?

A: Static Route Setup guides specified IP packets through
specified routers statically, useful for routing traffic between
different networks.

Q: How do I verify the current routing table?

A: Click on Static Route Setup > View Routing Table to check
the current routing entries.

„`

Static Route Setup
Въведение
If you have many private subnets behind the router, or you want to access another public subnet via an inside router, you can configure the router to route IP packets to those inside IP networks using 1st IP address/subnet mask fields on the LAN TCP/IP and DHCP Setup page.
The router also has RIP (Routing Information Protocol) built-in by default. If the neighboring routers have the same protocol, the RIP will be used for exchanging routing information. Here, the Static Route Setup just provides a way to guide specified IP packets through specified routers statically.
Конфигурация
– Add Static Routes to Inside Private and Public Networks Assume the Internet access setup has been configured and worked properly. You use the 1st subnet address 192.168.1.0/24 to surf the Internet and also an internal private subnet 192.168.10.0/24 via an internal router (192.168.1.2/24) and an internal public subnet 211.100.88.0/28 via an internal router (192.168.1.3/24). Also, the router 192.168.1.1/24 is a default gateway for the router 192.168.1.2/24. 1. Click LAN TCP/IP and DHCP Setup, select RIP Protocol Control as 1st Subnet, and then click OK button.
1

Note: To set RIP Protocol Control as 1st Subnet has two different meanings. The first one is that the LAN interface could be exchanged RIP packets with neighbor routers via 1st subnet (192.168.1.0/24). The second one is that those inside private subnets (ex. 192.168.10.0/24) could be NATed by the router to the Internet, but do IP routing for each other as well. 2. Add a static route to the inside private subnet 192.168.10.0/24 via the internal router 192.168.1.2/24. Click Static Route Setup > Index Number to add a static route to destination subnet 192.168.10.0/24 as below.
3. Add a static route to the inside public subnet 211.100.88.0/28 via 192.168.1.3/24.
2

Note: You should also add a static route in the router 192.168.1.3/24 to route IP packets to 192.168.1.0/24 and 192.168.10.0/24 subnets via the router 192.168.1.1/24. 4. Click Static Route Setup > View Routing Table to verify the current routing table.
– Delete or Deactivate a Static Route 1. Click Static Route Setup > Index Number which you want to delete. 2. Select Status/Action to Empty/Clear. Click OK button to delete the route.
3

Документи / Ресурси

DrayTek Static Route Setup [pdfИнструкции Static Route Setup, Route Setup

Референции

• Ръководство за потребителя