BenQ Interactive Flat Panel RP8602 Instructions
Disassembly process
| Dismantle 4 pieces of M8 x 20mm P head flat tail ,elastic pad black galvanized machinery screws. |
|
| Dismantle 3 pieces of M3 × 6mm meson head nickel plating mechanical screws. |
|
| Dismantle 16 pieces of M3 × 6mm meson head nickel plating mechanical screws. |
|
- Dismantle 15 pieces of M4 × 6mm flat round head nickel plating mechanical screws.
- Open the back cover.
|
|
- Dismantle 3 pieces of M4 × 6mm flat round head nickel plating mechanical screws.
- Dismantle 1 piece of Ф4 x 5 mm round head toothed pads blue zinc plating machine screw.
|
|
| 3. Remove the AC bracket. |
 |
- Dismantle 8 pieces of M3 × 6mm meson head nickel plating mechanical screws.
- Dismantle 7 pieces of M4 × 6mm flat round head nickel plating mechanical screws.
- Remove the back shell at the bottom.
|
|
- Dismantle 2 pieces of M4 × 6mm flat round head nickel plating mechanical screws.
- Remove the IO baffle.
|
|
- Dismantle 3 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove the USB board.
|
 |
- Dismantle 4 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove the MIC board.
|
|
- Dismantle 3 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove the OPS board.
|
|
- Dismantle 4 pieces of M5 × 8mm meson head black galvanized mechanical screws.
- Separate the EVA pad from the sound.
|
 |
- Dismantle 7 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove the motherboard.
|
|
- Dismantle 6 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove the power panel.
|
|
- Dismantle 2 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Dismantle 2 pieces of M3 × 4mm meson head nickel plating mechanical screws.
- Remove the OPS iron bracket.
|
 |
- Dismantle 3 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove the iron support.
|
|
- Dismantle 3 pieces of M3 x 5mm flathead flat tail blue zinc plating machinery screws.
- Remove the iron support.
|
|
- Dismantle 4 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove the horn bracket.
|
 |
- Dismantle 3 pieces of M4 × 6mm flat round head nickel plating mechanical screws.
- Remove the IO baffle.
|
|
- Dismantle 3 pieces of M3 × 8mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove the shielding can.
|
|
- Dismantle 8 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove 8 plastic buckles.
|
|
- Dismantle 6 pieces of M3 × 6mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove 6 rear shell supports.
|
|
- Dismantle 10 pieces of M3 × 8mm P head, flat tail, elastic pad, flat pad, blue galvanized mechanical screws.
- Remove aluminum profile assembly.
|
 |
- Dismantle 2 pieces of M3×3mm H =11mm flat tail Blue zinc plating machinery hexagon studs.
- Dismantle 4 pieces of M3×2.5mm H =5mm flat tail Blue zinc plating machinery hexagon studs.
|
|
Disassembly Time
Total time: about 35 minutes
Published: November 18, 2021
Updated: November 29, 2021
