BEKUP Model V2 E-Bike

IMPORTANT NOTICE
Please read this manual carefully before use. This manual contains important safety information, operating instructions, and maintenance guidelines.
Failure to follow the instructions and warnings in this manual may result in vehicle damage, serious injury, or other safety
Safety Instruction
- Thank you for choosing our products.
- To ensure your safety and health, we encourage you to read this manual thoroughly before you assemble the bike and take the first ride. Safe and effective use can only be assured if the equipment is assembled, maintained, and used properly. More importantly, this will offer you a general understanding and get the most out of your bike. Please check your electric bike before every ride, especially when traveling long distances.
- This manual is intended as a general guide to your new e-bike. For technical support, including repair information, please consult your dealer.
Things to know before use:
- Do not use the product before carefully reading the instructions from this manual and understanding the performance of the item.
- Don’t lend this product to people who can’t operate it, so as not to cause harm, if you lend the bike, please let the user follow instructions, it could help to decrease the risk of accident.
- The E-bike cannot be used as off-road vehicles or used for extreme bicycle sports, when riding the bicycle, please wear a safety helmet and protective
gear. It is forbidden to ride with one hand. - Please abide by the traffic rules and prohibit riding on motorized lanes and roads with multiple pedestrians.
- Carry people or objects in accordance with the requirements of laws and regulations, and do not park in the building’s lobby, evacuation stairs, walkways, and safe entrances and exits.
- It is recommended to charge and park in an outdoor dedicated parking hall, while avoiding rain, when charging, keep away from combustibles, and the charging time should not be too long.
- For safety reasons, please do not change the default speed setting of the electric bicycle and do not exceed speed limit in accordance with the traffic
rule. Riding on non-motorized lanes, downhills and paved roads not exceeding 15km/h.
Safety Instruction
- When adjusting the handlebar or saddle, please be careful not to exceed the safety line markings on the handlebar and saddle.
- Please check the tire pressure before riding, the recommended tire pressure is 35- 45PS.
- Please check the power circuit, lighting circuit, etc. before riding.
- Before riding, please check whether the front and rear brakes work normally, check the fastening status of the handlebars and front and rear wheels, and check whether the reflector is damaged or contaminated.
- When using the motor, please be careful not to hit vigorously and keep the rotating shaft lubricated.
- Try to avoid traveling in severe weather such as heavy rain.
Riding in rain or snow, the braking distance will be extended, pay attention to slow down. - It is not allowed to exceed the maximum load of the vehicle body when riding ( the maximum load is 125KG).
- It is suitable for people between 16 and 50 years old, and it is strictly forbidden to drive electric bicycles on the road by people under 16 years old.
General Information
About BEKUP Electric Bike
BEKUP electric bike is a leading icon of e-bikes. For years, BEKUP has been not only dedicating to innovation, cutting-edge technology and premium materials, but also providing cost effective e-bikes, to satisfy riders’ various needs of transportation and even desire of exploring sports & outdoors life. Just ride freely with BEKUP !

Bike Usage
Before Riding
- Before riding the bike on the open road, try all the settings on the electric bike, and get used to various results in a safe and controllable environment.
- Please check the power circuit, lighting circuit, and test the brake system before cycling.
- Always check the tire pressure before starting to ride, and make sure that the tire is inflated to a pressure within the specified range.
- If the pressure is too low, the wheel may be damaged, or the inner tube may be squeezed, causing the tire to leak air.
- If the pressure exceeds the recommended maximum value, the tire may blow out of the rim, which may damage the bicycle and cause injury to the cyclist and nearby people.
- In order to ensure the safety of riding, please check regularly for loose parts or screws. The places that need to be checked include but not limited to the seat tube, wheel, handlebar and pedals.
- If necessary, please confirm whether the battery capacity can meet you riding demand.
During riding
- Please wear helmets and riding gear that meet the requirements in accordance with regulations.
- Avoid traveling in severe weather such as heavy rain.
- Carry people or objects in accordance with the requirements of laws and regulations, and the load of the entire bike should not exceed 125kg.
- Obey the traffic rules.
After riding
- After heavy use, do not touch the hot surface, such as the disc brake rotor or the side edge of the brake rim.
- When folding the kickstand, always make sure that the stand is secure and the base is firm to prevent the bicycle from falling.
- If the bicycle is splashed with moisture, please wipe it dry and clean in time.
Brake Adjustment
Ensure that the brake cables are properly inserted into the brake levers before aligning a mechanical disc brake. If the disc rotor is bent or damaged, replace the rotor first.
- Loosen or tighten the barrel adjuster at the end of the brake cable lever.
This will make a small adjustment to the gap of the brake pads. If this is not enough to create the correct gap, then: - Loosen the two positioning bolts, but do not remove them. Slowly rotate the wheel and check the space between the rotor and the brake pad; adjust the position
of the brake pad so that the rotor does not rub and is slightly close to the outer pad (the gap between the rotor and the pad should be just enough to prevent friction). Make sure that the rotor and the pads are parallel to each other.
After the adjustment is complete, tighten the bolts. - If the rotor always rubs against the brake pads or the gap is too large, you can adjust the brake pad gap by loosening the cable clamp bolts and slightly releasing the cable to increase the gap or tightening the cable to reduce the gap, and then tighten the bolts again.
Shifting Recommendations
In order to increase the range, we recommend shifting according to the speed.
- For starting and low-speed riding, it is best to use a low-speed gear.
- At higher speeds, a higher gear should be selected.
Installation And Adjustment
Open the package of the bike, take out the electric bike and all the accessories inside and use the tool to cut off the packing rope.
Install the kickstand and front wheel
- Loosen the screws on the kickstand, align them with the pre-drilled holes on the frame, then retighten the screws.

- Remove the retaining rod at the top of the front fork, then mount the front wheel onto the fork. Ensure proper positioning of the disc brake mount..
- Insert the quick-release skewer through the fork ends and front wheel hub, then tighten securely.

Install the Front Fender and Front Light.
Remove the screws fixed on both sides and the middle top of the front fork. Position the mudguard and headlight properly (see Figure 3: bend the mudguard stay and thread it over the top of the front wheel), then retighten with the removed screws..

Install the stem and handlebar
- Loosen the screw at the top of the steerer tube, remove the end cap and expansion plug, then slide the stem onto the steerer and align it with the limit mark.
- Fit and straighten the handlebar, then tighten the stem clamp bolts step by step to secure everything.

- Loosen the stem clamp bolts and open the stem cap, then place the handlebar into the clamp seat.
- Align the handlebar properly, arrange the brake and motor cables neatly, and tighten all bolts evenly.

Install the rear rack and connect the brake light wiring
- Loosen the pre-installed screws on the rear frame dropout and the stay above the rear wheel, fit the rear rack into place, align the mounting holes, then retighten all screws securely.

- Align the male and female waterproof connectors of the brake light, plug them in tightly, screw the locking cap, then arrange and fasten the wiring to the frame.

Install Pedals
Check 2 pedals, the one imprinted “L” should install on the left side and “R” on the right side. Please use a wrench to tighten them.

Install the Seat Post
- Open the seat post and saddle, then install the rear reflector.
- Adjust seat post to the height that suits your riding position best and tighten quick release. (Please make sure that the quick release is tightened firmly.)

Turn on the power supply
Press the power button to turn on the power and activate the display.

- Your BEKUP e-bike is ready for use.
Meter Operation
Meter Instruction
FunctionalAreaDistributionInterface

Function overview
- Battery level display
- Assist level adjustment and indication
- Speed display (including real time speed, maximum speed, average speed)
- Mileage display (including single trip mileage and total mileage)
- Assist push control and indication
- Headlight control and indication
- Error code display
Button definition
Power On/Off button
, Increase button + , Decrease button –
Regular Operations
Power on/off
Keep pressing the “
” key, the instrument starts to work and the working power of the controller is turned on. In the power-on state, long press the “
” key to turn off the power of the electric bike. In the shutdown state, the meter no longer uses battery power, and the leakage current of the meter is less than 1uA.
Note: If the electric bike not used for more than 10 minutes, the meter will automatically shut down.
Display interface switching
After powering on, the display defaults to showing real-time speed (km/h) and total mileage (km). Press the “
” button to toggle between total mileage (km), single trip mileage (km), Voltage Display, Motor Output Power.

Assist Push Mode
Keep pressing the “- ” button, the electric bike enters the electric power Assisted-push Mode. The electric bike travels at 6km/h. At the same time, the screen displays . Release the “
” button and theelectric bike will immediately stop power output and return to the state before boosting.

Note: The Electric Power Assisted-push function can only be used when the User is pushing the electric bike, please don’t use it while riding. 3.4 Turn headlight on/off
Hold Key ” +” to turn the headlight on/off
Assist level selection
Press the “+/-” button to switch the power assist level of the electric bike to change the motor output power. (The following pictures only illustrate the different speeds of different gears, the specific speeds are subject to the actual product).

3.6 Power indicator
The battery power is displayed in five segments. When the battery is fully charged, all five segments light up. When the battery is under voltage, the outer frame of The battery flashes, indicating that it needs to be charged immediately.

3.7 Error code display
When an electric bike electronic control system fails, the instrument will automatically display an error code. Please see the table below for detailed error code definitions.

When an error code appears on the display, please troubleshoot the issue promptly. The electric bike will not operate normally after a fault occurs.
Battery And Charging: Further Information
Battery: Further information
- Keep the battery out of reach of children.
- Charging at 0°C~40°C/ 32°F~104 °F, and discharging at -5°C~40°C/ 23 °F~104 °F. Please do not store the battery in temperatures above 35 °C/ 95°F or below – 5°C/ 23°F.
- Keep the battery dry, do not put the battery in acidic or alkaline liquid, keep away from rain, fire and high temperature environment.
- It is strictly forbidden to connect the positive and negative poles of the battery reversely, and it is strictly forbidden to damage, disassemble or short-circuit the battery.
- Used batteries are hazardous chemicals, and the used batteries should not be disassembled without authorization, and recycled by relevant professional departments.+
Charging: Safe operation guide
- Please follow the instructions for use, otherwise the consequences are at his own risk. Please use the original special charger. It is strictly prohibited to use other chargers.
- Pay attention to the battery type and applicable voltage that the charger can charge, and it is strictly forbidden to mix them. The charging time shall not exceed 12 hours, and the charging current shall not exceed 3A.
- When charging, it should be placed in a ventilated environment, and it is strictly forbidden to charge in a confined space or in a hot environment.
- When charging, insert the battery first, then add the mains. After charging fully (the green light will be on), first cut off the mains, and then unplug the battery. It is forbidden to connect the charger to the AC power supply without load for a long time. During the charging process, if the indicator light is abnormal, a peculiar smell appears, or the charger casing is overheated, stop charging immediately, and repair the charger or replace the charger.In the process of use and storage, pay attention to avoid the entry of foreign objects, especially avoid the inflow of water or other liquids, so as to avoid short circuit inside the charger.
- When not in use for a long time, keep the battery in a cool and dry place, and charge the battery for two hours a month.
Reminder
- Charge a new battery 5~6 hours before you use it in your product for the first time. If the battery is dropped or damaged due to a bicycle accident, there may be a danger of electrolyte leakage. Please stop using it immediately.
- It is better not to wait until the power is completely exhausted before charging, which can more effectively extend the battery life. Besides, Overheating or undercharging the battery may shorten battery life.
- How far can a fully charged battery go? It depends on the load weight, road conditions and battery capacity. But under the same conditions, the average speed can last longer riding distances. Using pedal assist mode allows you to go further.
Battery Disposal
- Battery must be recycled or disposed of in an environmentally sound manner.
- Do not dispose of the battery in a fire. The battery may explode or leak.
- Do not dispose of a battery in your regular household trash.
Maintenance
- ● The front and rear wheels of the vehicle should be located in the center of the front fork or frame.
● After riding, please store the bike in a place without sunlight and rain.
● Water showering is forbidden, and the surface of the bike body can be wiped with a semi-dry cloth.
● Do not touch the charging hole on the bicycle, or touch it with metal or liquid, otherwise, it maycause an accident due to an instantaneous short circuit of the current.
● Check all cables and cable housings for fraying, breaks, rust, or corrosion and replace if necessary.
● Check the motor and brake frequently, and do not fill the brake area with oil. Additionally, check the brake pads for any damage as they will be worn over time and eventually need replacement.
● Regularly check the various screws of the bike and the places that need to be fastened, and regularly reinforce to prevent injury and unnecessary wear and tear on your e-bike.
● Recommended torque (unit: kgf.cm): the horizontal screw 60-80, the stem screw
175- 200, the seat cushion screw 175-250, the wheel screw 320-450.
● Regularly check the tension of the chain, which can be adjusted by the chain regulator.
● Always check the tire for scratches, cracks, or excessive wear. The inner tube and the valve should be perpendicular to the wheel hub and not crooked. Accidentally punctured, damaged or excessively worn inner and outer tires need to be replaced immediately, please seek professional technicians to repair or replace your tires.
● It is forbidden to modify key structural parts such as the frame, front fork, standpipe, and electrical function parts. If damaged, use the original parts to replace it. Otherwise, the guarantee service will not be provided. Any loss or damage caused by the modification shall be solely responsible.
Warranty
BEKUP provides warranty service for the electric bikes. If there is a hardware defect and a valid claim is received during the warranty period, we will resend new parts within the scope permitted by law.
The Warranty covers product defects in materials and workmanship under normal use. This Warranty is limited to original purchasers and is not assignable or transferable.
Warranty Coverage
Note:
- If the motor breaks down after it has been replaced for once within the warranty period, we will charge for replacement and freight by then.
- The battery housing is not under warranty scope.
Attachment

Remarks:
- After fully charged, the charger indicator light turns from red to green.
- The amount of battery remaining, load of the bike(weight of rider and cargo), tire pressure, road environment, chain and wheel axle lubrication, etc. will affect the maximum speed;
- Riding habits, temperature, load, tire pressure, road environment and other factors will affect the riding range.
Customer Services
We provide lifetime customer support services. For any questions about the product, please contact customer service from where you brought the equipment. We will be
happy to answer your questions.
Any question about the item, please contact the Customer Service: BEKUP support team: service@bekupebike.com
Scan the QR code above to watch the assembly video.

Documents / Resources
![]() | Model V2 E-Bike |
References
- Redirecting...kgf.cm
- User Manualmanual.tools

