Lutron Athena Clear Connect Gateway – Type X

Product Overview

The Athena Clear Connect Gateway – Type X is a ceiling-mounted device that integrates Clear Connect – Type X devices, including Ketra loads, with Lutron's existing Clear Connect – Type A and QS devices through the wired Athena Edge Processor. It enables compatible Lutron control systems to communicate with up to 50 wireless, Clear Connect – Type X devices, including Ketra Intelligent Light Sources.

Features

• Powered by an IEEE 802.3af-2003 or 802.3at-2009 compliant Power over Ethernet (PoE) supply, such as the Lutron model Q-POE-PNL, or by other compliant supplies.
• Compatible with the following Ketra lighting fixtures: A20, S30, S30 Track, S38, S38 Track, G2 via N3, L31 via N3, L4R via N3, D3, D4R. For a complete list of compatible models, visit www.ketra.com.
• Requires at least one Athena QP5-xL-POE panel or QP6-1L and a compliant PoE supply. Refer to the Athena Light Management Hub installation instructions for setup and other information.
• A maximum of 16 total gateways and Athena Edge processors can be on one system.
• Requires Athena Designer software version 1.0 or later.

Specifications

Regulatory Approvals

• cULus
• FCC
• IC

PoE Power

• Requires 48 V⁺ 100 mA (IEEE 802.3af-2003 or 802.3at-2009 compliant PoE supply).
• If designated Ketra emergency fixtures are within the gateway's subnet, the gateway's PoE must be supplied via a normal-only feed, not an uninterruptible power supply or generator.

Environment

• Operating temperatures: 32 °F to 104 °F (0 °C to 40 °C).
• Relative humidity: 0% to 90% non-condensing.
• For indoor use only.

System Communications and Capacity

• Communicates through a wireless mesh network.
• Controls up to 50 Clear Connect – Type X devices, depending on the model.
• Can send a Clear Connect – Type X command to its subnet once per 250 ms.

ESD Protection

• Tested to withstand electrostatic discharge without damage or memory loss, in accordance with IEC 61000-4-2.

Surge Protection

• Tested to withstand surge voltages without damage or loss of operation, in accordance with IEEE C62.41-1991 Recommended Practice for Surge Voltages in Low-Voltage AC Power Circuits.

Power Failure

• Features 10-year power failure memory. Upon power restoration, the gateway returns to its previous state prior to the interruption.

Mounting

• Can be recess-mounted or wall-mounted using the recess bracket, or junction box mounted.
• When mounting on a 4 in x 4 in (102 mm x 102 mm) junction box, a mud ring (not supplied) must be used.
• Each Clear Connect – Type X device must be within 71 ft (22 m) of a centrally located Clear Connect Gateway.
• Each Clear Connect – Type X device should have two or more non-battery powered Type X devices within 25 ft (7.6 m) of another compatible Clear Connect – Type X device.
• Must be mounted 5 ft (1.5 m) away from wireless interference sources like microwaves or Wireless Access Points (WAP).
• Do not install the gateway in metallic enclosures.

Wiring

• Use Cat5e minimum cable.
• Maximum wire length is 328 ft (100 m).
• Each gateway requires a home run Ethernet connection back to a PoE switch.
• Do not run PoE wiring outdoors.

Dimensions

All dimensions are shown in inches (mm).

Front View: Diameter 4.04 in (102.67 mm)

Side View: Height 1.17 in (29.82 mm)

Back View: Features status and program indicators, power input, Ethernet port, and FCC/IC information.

Mounting Details

Recess/Wall-Mount

Ceiling thickness: Minimum 0.30 in (7.62 mm) to Maximum 1.20 in (30.48 mm). Requires a 3.25 in to 3.5 in (83 mm to 89 mm) opening.

Surface-Mount

Use appropriate mud ring for ceiling tile thickness. Use mud ring with hole spacing as shown in the diagram (mud ring not included with any models).

Note: Both the recess-mount and surface-mount adaptors ship with the Athena Clear Connect Gateway – Type X units.

System Riser Diagram

Illustrates the connection of QP5, Q-POE-PNL, and the Athena Clear Connect Gateway – Type X within a system, connected to a building network.

Note: Refer to the IT Guide at www.lutron.com/ITguide for more information on networking requirements.

Range Diagram

All Clear Connect – Type X devices must be within 71 ft (22 m) of the Athena Clear Connect Gateway – Type X.

Notes:

• The Athena Clear Connect Gateway – Type X cannot span multiple floors.
• Should be mounted in the middle of a non-metal ceiling tile or drywall, visible from inside the space.
• Installation near metal (other than a junction box) may reduce RF range. Keep at least 12 in (305 mm) away from metal objects.
• Should not be mounted within 5 ft (1.5 m) of a Wireless Access Point.

The diagram shows the coverage area of the Athena Clear Connect Gateway – Type X, indicating a maximum range of 71 ft (22 m).

Choose a Location to Install

Mount the gateway centrally in relation to other Clear Connect – Type X devices. A minimum of two or more Clear Connect – Type X devices must be within 25 ft (7.6 m) of the gateway. Each Clear Connect – Type X device should have two or more non-battery powered Type X devices within 25 ft (7.6 m) of another compatible Clear Connect – Type X device.

The diagram illustrates placement within a floor plan, showing optimal distances for Clear Connect – Type X devices and Wireless Access Points.

Fixture Legend:

• ■ = Clear Connect – Type X Ketra Lamp
• ■ = Ketra Linear Fixture
• ■ = Clear Connect - Type X Ketra N3
• ■ = Athena QP5-2L-POE Hub
• ■ = Athena Q-RF Clear Connect Gateway – Type X
• ■ = Wireless Access Point

Athena Security Statement

Lutron prioritizes cybersecurity with a proactive approach, monitoring the threat landscape and continuously enhancing systems and processes. This approach is called "Secure Lifecycle". Key aspects include:

• Security by Design: Dedicated security team ensures best practices are implemented during system development.
• Third-Party Validation: External experts are leveraged to review and validate security measures.
• Continuous Monitoring and Improvements: A dedicated security team monitors for potential threats and deploys security patches.
• Ongoing Support: Resources are available to answer security-related questions.

Security features incorporated into product designs include recommendations from NIST and aim to meet secure lifecycle protections. Examples include:

• Secure and authenticated remote access with unique keys for every Athena system.
• A secure hardware element ("chip") on all Athena processors and Clear Connect – Type X Gateways to protect communication keys.
• Enforcement of industry-standard encrypted communication for integration protocols. Third-party components should be evaluated independently.
• Secure commissioning with encrypted and authenticated communication between software and processors, requiring permission for system access.
• Automatic security updates for urgent patches. Lutron commits to one year of security support from system start-up.
• Use of industry-standard techniques for cloud-based integrations, such as OAuth2.0.
• Signed processor firmware to ensure authenticity of updates.

For questions or to report a vulnerability, contact Lutron's 24/7 Technical Support at 1.844.LUTRON1 or support@lutron.com.