Chipper 2XTMBT
Advanced mPOS Design Integrating Bluetooth®
Magstripe, EMV and NFC Card Reading Functions
Support Operating System:
iOS, Android, Windows Phone 8, MS Windows
Index & Accessories (Fig.1)
Package Contents
- Device X1
- USB cable X1
- Lanyard X1
- Quick Start Guide X1
Application Download & Installation
This device can support either iOS & Android.
- Please download the official application from app stores before operation.
- Please follow app instructions to register and login for proper operation.
- For any questions, please contact the official application developer.
Quick Start Procedures
STEP 1
Connect Micro USB charging cable to charge the device as shown to the right.
Download the official application from APP Store or Google Play Store.
** Chipper™ 2X BT is powered by an internal Lithium Polymer rechargeable battery pack that cannot be removed or replaced. Before first use, charging is required for approximately two to three hours. To prevent potential electrical damage to the Chipper™ 2X BT, please be recommended to use the Micro USB cable provided with the packaging only.**
STEP 2
Turn on the device pairing function of your smartphone/tablet. Then, press “ ” to turn on the Chipper™ 2X BT.
** Please ensure that Bluetooth® function of your smartphone/tablet is ON before device pairing.
Quick Start Procedures
STEP 3
Select Chipper™ 2X BT in the Scanned Device List on your smartphone/tablet. Then, your Chipper™ 2X BT is connected and green LED will ON.
STEP 4:
You can follow your application instruction to start the transaction process, then swipe, insert or tap card to complete the transaction.
** If you pay via swiping card or inserting EMV IC card, please ensure that the magstripe or EMV chip of the card is facing the right direction. If you pay using NFC card, please ensure you tap the NFC payment card within 4cm range on top of the NFC marking.
NFC Status indicators
Cautions & Important Notes
- Ensure the device is fully charged before use.
- Please ensure the magstripe/ EMV chip of the card is facing the right direction when swiping or inserting card.
- The NFC card should be tapped within 4 cm range on top of the reader mark.
- Don’t drop, disassemble, tear, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint or insert foreign object into the device. Doing any of which will damage the device and void the Warranty.
- Don’t immerse the device into water and place near washbasins or any wet locations. Don’t spill food or liquid on the devices. Don’t attempt to dry the device with external heat sources, such as a microwave or hair dryer. Don’t use any corrosive solvent or water to clean the device. Recommend using dry cloth to clean the surface only.
- Don’t use any sharp tools to point the internal components, connectors or contacts, doing which may lead to device malfunction and void the Warranty simultaneously.
Product Specifications
| Functions |
|
| Communication Interface | Bluetooth® |
| Power & Battery | Lithium polymer rechargeable battery 650mAh, 3.7V |
| Charging | Via micro USB |
| Swipe Speed | 15cm/sec – 100cm/sec |
| LED Indicator | All LEDs off – button release to power down Red LED on -device starting up / Charging battery Red LED off – fully charged Red LED flashing – low battery / Critical low battery Blue LED on -bluetooth is connected Blue LED flashing – standby mode / waiting for connect bluetooth or bluetooth is disconnected |
| NFC LED Indicator | Connecting with POS terminal – First LED flashing Ready for NFC Reading – First LED on Success Reading – 4 LEDs on in consecutive order Transaction Completed – One “BEEP” sound Errors – Two “BEEP”sound Power off – All LEDs off |
| Key Management | DUKPT, MK/SK |
| Encryption Algorithm | IDES |
| Support Operating System | Android 2.1 or above iOS 6.0 or above Windows Phone 8 MS Windows |
| Product Size | 66.6 x 59.7 x 18.5mm / 2.62 x 2.35 x 0.73inch (approx.) |
| Product Weight | 67g / 2.36oz (approx.) |
| Operating Temperature | 0°C – 45°C (32°F – 113°F) |
| Operating Humidity | Max 95% |
| Storage Temperature | -20°C – 55°C (-4°F – 131°F) |
| Storage Humidity | Max 95% |
| Sticky Pad | Removable adhesive |
| Sticky Pad Size | 46.6 x 38mm / 1.84 x 1.50inch (approx.) |
Troubleshooting
| Problems | Recommendations |
| Device cannot be paired |
|
| Device lost the connection with your smartphone or tablet when the device is auto-off. |
|
| Device does not work with your phone or tablet |
|
| Device cannot read your card successfully |
|
| Device has no response |
|
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Warranty
- Any damage or defects caused by a failure to follow the instruction which relate to this device or as the result of an accident, abuse, misuse, misapplication, product modification, improper voltage or current, acts of God, shipping damages or loss, or damage caused by service performed by anyone other than our company are expressly excluded from the warranty stated below.
- We are not under any obligation to support the device for all operating environments, including but not limited to, interoperability with all current and/ or future versions of software or hardware.
- Please contact the dealer for any warranty or customer support services. Any repair of the device by yourself will void the Warranty.
FCC Supplier’s Declaration of Conformity:
Chipper 2X BT / CHB28
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
BBPOS Corp.
970 Reserve Drive, Suite 132 Roseville, CA 95678
www.bbpos.com
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Need Help?
E: sales@bbpos.com
T: +852 3158 2585Room 1903-04, 19/F, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, Hong Kong www.bbpos.com
©2017 BBPOS Limited. All rights reserved. BBPOS and Chipper™ are either trademark or registered trademarks of BBPOS Limited.iOS is the trademark of Apple Inc. Android™ is a trademark of Google Inc. Windows® is a registered trademark of Microsoft corporation in the United States and/or other countries. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by BBPOS Limited is under license. Other trademarks and trade names are those of their respective owners. All details are subject to change without prior notice.
Documents / Resources
 | bbpos Chipper 2X BT Card Reader [pdf] User Manual CHB28, 2AB7X-CHB28, 2AB7XCHB28, Integrating Bluetooth Magstripe EMV and NFC Card Reading Functions, Chipper 2X BT Card Reader, Chipper 2X BT, Card Reader |
