BANNER S15LPRGB7Q In-Line RGB Indicator Instruction Manual

Use Banner’s Pro Editor software and Pro Converter Cable to create custom configurations by selecting different colors, flash patterns, and animations.
For more information visit www.bannerengineering.com/proeditor.

Wiring

5-pin M12 Male 5-pin	M12 Female	Pin	Wire Color	Description
		1	Brown	Input 2: 12 V DC to 30 V DC
		2	White	Input 3: 12 V DC to 30 V DC
		3	Blue	DC Common
		4	Black	Input 1: 12 V DC to 30 V DC
		5	Gray	Input 4 (Default Flashing Input): 12 V DC to 30 V DC

Default Color Definition

	Red	Yellow	Green	Cyan	Blue	Magenta	White
Input 1	X	X				X	X
Input 2		X	X	X			X
Input 3				X	X	X	X

An “X” denotes an active input, for example when Input 1 and Input 3 are active, the indicator will show Magenta.
Pro Editor Configuration for the S15L
Banner’s Pro Editor software offers an easy way to configure Pro Series-enabled touch and indicator devices, allowing users full control of device states. The easy-to-use configuration software provides a variety of tools and capabilities to solve a wide range of applications. Configure any Pro Series-enabled device using the free Pro Editor software, available for download at www.bannerengineering.com/proeditor.
Color 1 and Color 2 Options

Green	Yellow	Sky Blue	Rose
Red	Lime Green	Blue	White
Orange	Spring Green	Violet	Custom 1
Amber	Cyan	Magenta	Custom 2

Intensity 1 or Intensity 2 Options

Intensity	Description
High	100%
Medium	60%
Low	25%
Off	0%
Custom	Set a custom intensity percentage

Animation Settings

Animation	Description
Off	Device OFF, no animation displays
Steady	Color 1 is solid ON at the defined intensity
Flash	Color 1 flashes at the defined speed, color intensity, and pattern (normal, strobe, three pulse, SOS, or random)
Two Color Flash	Color 1 and Color 2 flash alternately at the defined speed, color intensities, and pattern (normal, strobe, three pulse, SOS, or random)
50/50	Color 1 is displayed on one side of the indicator and Color 2 is displayed on the other side of the indicator at the defined color intensities
50/50 Rotate	Color 1 is displayed on one side of the indicator and Color 2 is displayed on the other side of the indicator while alternating sides at the defined speed and color intensities
Intensity Sweep	Color 1 continuously increases and decreases intensity between 0% to 100% at defined speed and color intensity
Color Sweep	Color 1 and Color 2 define the end values of a line across the color gamut. The light continuously displays a color by moving along the line at the defined speed and color intensity
Wave	Color 1 increases and decreases intensity between 0% to 100% at defined speed and color intensity on one side of the indicator, then switches to other side of indicator; then Color 2 repeats same sequence
Double Wave	Color 1 increases intensity between 0% to 100% at defined speed and color intensity holding on one side of the indicator, then the other side of indicator increases intensity between 0% to 100%; then Color 2 repeats same sequence

Pulse Patterns

Pattern	Description
Normal	Alternating Color 1; Off or Color 2 at 50% duty cycle
Strobe	Continuous Color 1; Off or Color 2 flashes at 20% duty cycle
3-Pulse	Three consecutive Color 1 pulses at 10% duty cycle on Off or Color 2 background
SOS	Short pulse, short pulse, short pulse, long pulse, long pulse, long pulse, short pulse, short pulse, short pulse alternating Color 1 and Off or Color 2
Random	Random sequence of Color 1 and Off or Color 2 flashes

Speed

Speed	Description
Slow	0.5 Hz
Medium	1 Hz
Fast	5 Hz
Custom Flash Rate	Set a custom flash rate in Hz

I/O State Configuration Settings	Description
Basic	Configurations made in this state assign one wire to one state, with the following override control: • Pin 1 (Brown) overrides Pin 4 (Black) • Pin 2 (White) overrides Pins 1 and 4 (Brown and Black) • Pin 5 (Gray) overrides Pins 1, 2, and 4 (Brown, White, and Black)
Advanced	I/O state with full fifteen state options for maximum configuration. Configurations made in Advanced assign binary wiring combinations of all valid inputs to each state.
I/O Block	Three state control for use with I/O block. Configurations made in I/O Block assign states to the black, white, and combination of black and white wires for use with I/O blocks for which power (brown) and common (blue) are always on for five pin connections.

Specifications

Supply Voltage
12 V DC to 30 V DC
Supply Current
60 mA maximum current at 12 V DC 35 mA typical at 24 V DC
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Leakage Current Immunity
400 μA
Input Response Time
250 milliseconds maximum
Flash
Default 1 Hz flash rate through flash input wire
Operating Conditions
–40 °C to +45 °C (–40 °F to +113 °F)
Humidity: 90% at +50 °C maximum relative humidity (non condensing)
Storage Temperature: –40 °C to +70 °C (–40 °F to +158 °F)
Environmental Rating
IP65, IP67, IP68, UL Type 1
Construction
Coupling Material: Nickel-plated brass
Connector Body: PVC diffuse white
Vibration and Mechanical Shock
Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 0.5 mm amplitude, 5 minutes sweep, 30 minutes dwell) Meets IEC 60068-2-27 requirements (Shock: 15G 11 ms duration, half sine wave)
Connections
Integral 5-pin M12 male/female quick-disconnect connector Models with a quick disconnect require a mating cordset Required Overcurrent Protection
WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations.
Overcurrent protection is required to be provided by end product application per the supplied table.
Overcurrent protection may be provided with external fusing or via Current Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to www.bannerengineering.com.

Supply Wiring (AWG)	Required Overcurrent Protection (A)	Supply Wiring (AWG)	Required Overcurrent Protection (A)
20	5.0	26	1.0
22	3.0	28	0.8
24	1.0	30	0.5

Certifications
Banner Engineering BV
Park Lane, Culliganlaan 2F bus 3 1831 Diegem, BELGIUM
Turck Banner LTD Blenheim House
Blenheim Court
Wickford, Essex SS11 8YT
GREAT BRITAIN
Default Indicator Characteristics

Color	Dominant Wavelength (nm) or Color Temperature (CCT)	Color Coordinates(1)		Lumen Output (Typical at 25°C)
Color	Dominant Wavelength (nm) or Color Temperature (CCT)	x	y	Lumen Output (Typical at 25°C)
White	7000K	0.31	0.295	1.16
Green	527	0.175	0.7	1.8
Red	620	0.69	0.307	1.3
Orange	604	0.628	0.356	1.35
Amber	597	0.593	0.383	1.35
Yellow	588	0.537	0.426	1.35
Lime Green	577	0.466	0.481	1.8
Spring Green	513	0.178	0.562	1.6
Cyan	498	0.195	0.396	1.3
Sky Blue	489	0.17	0.303	1.1
Blue	465	0.144	0.055	0.25
Violet	–	0.337	0.144	0.7
Magenta	–	0.506	0.251	1
Rose	–	0.593	0.282	1.1

FCC Part 15 Class B for Unintentional Radiators
(Part 15.105(b)) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These imits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

(Part 15.21) Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Industry Canada ICES-003(B)
This device complies with CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions: 1) This device may not cause harmful interference; and 2) This device must accept any interference received, including interference that may cause undesired operation.

Dimensions

All measurements are listed in millimeters [inches], unless noted otherwise.

Accessories

Cordsets

5-Pin Threaded M12 Cordsets—Single Ended
Model	Length	Style	Dimensions	Pinout (Female)
MQDC1-501.5	0.5 m (1.5 ft)	Straight		1 = Brown 2 = White 3 = Blue 4 = Black 5 = Gray
MQDC1-503	0.9 m (2.9 ft)
MQDC1-506	2 m (6.5 ft)
MQDC1-515	5 m (16.4 ft)
MQDC1-530	9 m (29.5 ft)
MQDC1-560	18 m (59 ft)
MQDC1-5100	31 m (101.7 ft)
MQDC1-506RA	2 m (6.5 ft)
MQDC1-515RA	5 m (16.4 ft)
MQDC1-530RA	9 m (29.5 ft)
MQDC1-560RA	19 m (62.3 ft)	Right-Angle

5-Pin Threaded M12 Cordsets—Double Ended
Model	Length	Style	Dimensions	Pinout (Male)	Pinout (Female)
MQDEC-501SS	0.31 m (1.02 ft)

MQDEC-503SS	0.91 m (2.99 ft)
		Male Straight/ Female Straight		1 = Brown 2 = White 3 = Blue	4 = Black 5 = Gray
MQDEC-506SS	1.83 m (6 ft)
MQDEC-512SS	3.66 m (12ft)
MQDEC-515SS	5 m (16.4 ft)
MQDEC-530SS	9 m (29.5 ft)
MQDEC-550SS	15 m (49.2ft)

Brackets
LMBM12MAG

Attaches to M12 cordset end
Black polypropylene

11.8 kg (26 lb) pull force
One piece

LMBM12SP

Attaches to M12 cordset end
Black polypropylene
Supplied with thread-forming hardware
Pack of seven

LMBS15MAG

Attaches to S15 housing
White polypropylene
11.8 kg (26 lb) pull force
One piece

LMBS15SP

Attaches to S15 housing

White polypropylene
Clearance for M5 or #10 hardware
Pack of five

Quick-Disconnect Cap

ACC-CAP M12-10

10 Caps
Seal and protect exposed, unterminated cascade quick-disconnect connectors

Pro Editor Hardware

PRO-KIT
Includes:

Pro Converter Cable (MQDC-506-USB)

Splitter (CSB-M1251FM1251M)
Power Supply (PSW-24-1)

MQDC-506-USB

Pro Converter Cable
1.83 m (6 ft) length 5-pin M12 quick disconnect to Device and USB to PC

Required for connection to Pro Editor

CSB-M1251FM1251M

5-pin parallel Y splitter (Male-Male-Female)
For full Pro Editor preview capability
Requires external power supply, sold separately

PSW-24-1

24 V DC, 1 A power supply

2 m (6.5 ft) PVC cable with M12 quick disconnect
Provides external power with splitter cable, sold separately

PSW-24-2

24 V DC, 2 A Class 2 UL Listed power supply
100 V AC to 240 V AC 50/60 Hz input

3.5 m (11.5 ft) PVC cable with M12 quick disconnect
Includes Type A (US, Canada, Japan, Puerto Rico, Taiwan), Type C (Germany, France, South Korea, Netherlands, Poland, Spain, Turkey), Type G (United Kingdom, Ireland, Singapore, Vietnam), and Type I (China, Australia, New Zealand) AC detachable input plugs

ACC-PRO-CABLE5

Mating accessory for cabled and terminal models
150 mm (6 inch) PVC cable with M12 quick disconnect

Lever wire nuts included (qty 5)
Required to connect cabled models and screw terminal models to Pro Converter Cable, sold separately

Banner Engineering Corp Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp. Any misuse, abuse, or improper application or installation of this product or use of the product for personal protection applications when the product is identified as not intended for such purposes will void the product warranty. Any modifications to this product without prior express approval by Banner Engineering Corp will void the product warranties. All specifications published in this document are subject to change; Banner reserves the right to modify product specifications or update documentation at any time. Specifications and product information in English supersede that which is provided in any other language. For the most recent version of any documentation, refer to: www.bannerengineering.com. For patent information, see www.bannerengineering.com/patents.

LinkedIn
Twitter
Facebook

Documents / Resources

BANNER S15LPRGB7Q In-Line RGB Indicator [pdf] Instruction Manual
S15LPRGB7Q In-Line RGB Indicator, S15LPRGB7Q, In-Line RGB Indicator, RGB Indicator, Indicator

References

User Manual

Features

Configuration Instructions