GVM R1200B Bi-Color LED Monolight
“
Specifications:
- Product Name: GVM R1200B
- Temperature Range: -20 to 45 degrees Celsius
- Power Source: Built-in lithium batteries
- Warranty: 1 year (excluding consumables)
Product Information:
The GVM R1200B is a professional lighting equipment designed for
photography and videography enthusiasts. It features COB LED
technology, providing a wide-color temperature range suitable for
various shooting environments such as live streams, outdoor shoots,
studios, and YouTube videos.
Usage Instructions:
Safety Instructions:
This product should be operated by a qualified lighting
technician or under professional supervision. Follow these safety
precautions:
- Read the product manual carefully before use.
- Operate the product within the temperature range of -20 to 45
degrees Celsius. - Avoid placing the equipment near flammable substances.
- Allow the device to cool down completely before storing
it. - Properly place power cords to avoid damage or tripping
hazards. - Use original power cords provided by the manufacturer.
- Avoid using non-recommended product accessories.
- For products with built-in lithium batteries, use a dedicated
charger within the prescribed voltage and temperature range.
Product Care:
Ensure that the heat dissipation port is not covered during
operation. Keep children away from the equipment and operate it
correctly according to the user manual.
FAQ:
Q: Can I use this product without professional
supervision?
A: This product is recommended to be operated by a qualified
lighting technician or under professional supervision for safety
reasons.
Q: What happens if I use non-original power cords?
A: Damage caused by using non-original power cords is not
covered by the repair service warranty.
“`
GVM R1200B
V0
CONTENTS
Important Safety Instructions ——————————————— Page 1~2 Warning ———————————————————————– Page 2 Product Introduction ———————————————————- Page 3 Disclaimers ——————————————————————– Page 3 Product Parameter ———————————————————— Page 4 Precautions ——————————————————————– Page 4 Product Structure Diagram ————————————————— Page 5 Installation Method ——————————————————– Page 6~9 Description Of Product Control Keys ————————————— Page 10 Function Introduction & Instructions For Use ————————– Page 11~15 APP Control ————————————————————– Page 16~17 Quick Troubleshooting —————————————————— Page 18 Use And Maintenance ——————————————————- Page 19 Packing List —————————————————————— Page 19 Product Warranty ——————————————————– Page 20~21
IMPORTANT SAFETY INSTRUCTIONS
This product is professional lighting and staging equipment and should only be operated by a qualified lighting technician or used under the supervision of a professional. Always follow the precautions below to ensure safe and proper usage.
1Read the product manual carefully before use. 2This product is only suitable to use in a temperature range of -20 to 45. 3Do not place the equipment near flammable and volatile solvents such as alcohol and
gasoline. 4Before storing the device, make sure it has cooled down completely. When being stored,
unplug the power cord from the device. The equipment should be stored in its carrying case or a well-ventilated and dry place. 5This lighting fixture is not for general illumination and should not be used as such. Individuals with eye injuries or sensitivity should avoid using this lighting fixture. 6This is a professional light and children are prohibited from using it. Parents or guardians must closely supervise children when they are near the equipment to prevent personal injury caused by colliding with or misusing the equipment. 7Before using the equipment, please remove the protective cover. 8When the lighting fixture is on, it is forbidden to stare directly at the light source under any circumstances. High-intensity lighting should only be used under the guidance of a professional lighting technician. Avoid staying in a high-intensity light environment for a long time. If feeling any discomfort, please immediately turn off the lighting fixture, and seek medical attention. 9When the lighting fixture is on, use it carefully and avoid contacting high-temperature components such as LED light sources to prevent being burnt. 10.Do not use damaged equipment or accessories. Wait for a professional repairman to inspect and repair it before it is confirmed that the equipment can function normally. 11.If the light source is damaged or deformed due to heat, please stop using it and contact the manufacturer, service agents, or qualified repairman promptly to replace the light source to avoid accidents. 12.If the product is cracked due to falling, squeezing, or strong impact during use, please stop use it to avoid being electrically shocked by touching internal electronic components. 13.Do not disassemble the product by yourself. If the product malfunctions, it must be checked and repaired by the manufacturer or authorized repair personnel. 14.Before cleaning and maintenance, be sure to unplug the power supply. To unplug never pull on the cable but always pull the plug itself. This device shall only operate with earthed power outlets or emergency power generators. 15.When cleaning the device, do not wipe it with a wet cloth. Use a dry and soft cloth to wipe off the dirt. 16.If an extension cord is required, it needs to have the necessary capacity to power the respective unit. Using an extension cord with a lower current capacity than the devices need may cause overheating.
1
17.For some products with long power cords, please place the power cords properly and avoid contact with overheated surfaces that may damage or trip personnel. Please use the original power cords of our manufactory. The damage caused by using non-original power cords is not covered by our repair service.
18.Do not use product accessories that are not recommended by our brand to avoid fire, electric shock, or personal injury.
19.Some products use batteries for power supply. Do not use any batteries, power sources, or accessories that are not specified in the user manual. Please keep batteries and other accessories out of reach of children and infants. If a child or infant swallows a battery or accessory, seek medical attention immediately. If the battery leaks, changes color, deforms, smokes, or emits an odor, remove it immediately. Be careful not to get burned during the removal. Continued use of such batteries may cause a fire, electric shock, or skin burns. Do not use any deformed or modified batteries. Do not disassemble or modify this product or the battery. Do not heat the battery or solder it. Do not let the battery come into contact with fire or water, or subject it to strong external force. Do not insert the battery’s positive and negative ends incorrectly, or mix and use old and new batteries or different types of batteries.
20.For some products with built-in lithium batteries, please use a dedicated charger for charging, and following the correct operating instructions within the prescribed voltage and temperature range.
21.The warranty last for one year. Consumables like batteries, adapters, power cords, and other accessories are not covered by the warranty.
22.The one-year warranty will be invalidated if the equipment is found to have been repaired privately. The related repair costs will be charged.
23.Equipment malfunctions caused by non-standard operations are not covered by the warranty.
24.The safety instructions are based on our factory’s strict testing. If there are any changes in the equipment’s design and specifications, we reserve the right not to notify you. Customers can visit our official website to check the latest digital version of the instructions and learn about the newest product information.
Keep these instructions!
WARNING:
High-power LED lights are strictly prohibited from being directly viewed or shining into other people’s eyes. Do not unplug the power cord or connecting wires while the light is on to avoid personal injury. Do not cover the heat dissipation port when the lamp is in operation. Keep children away from touching or using this light. As professional lighting equipment, please make sure to operate it correctly according to the user manual.
2
PRODUCT INTRODUCTION
Thank you for purchasing the “GVM R1200B”. This product is specifically designed for photography and videography enthusiast. This product is suitable for use in live stream /outdoor /studio and YouTube shoots. The main features of the product are: 1Equipped with COB LED technology, it features a wide-color temperature range of
2700 to 6800K, and allowing for step-less adjustment of light intensity. With a color rendering index of 97+, it helps restore and enrich the colors of objects, providing you with a natural and vibrant light quality. 2APP control, which can be connected and operated through your iOS and Android smart mobile devices. It supports Bluetooth Mesh networking and can be group and interlinked with GVM brand devices that support Mesh networking. 3It is equipped with a standard DMX 512 in/out port, which enables lowprecision 8bit and high-precision 16-bit DMX control modes, and supports for RDM. 4Equipped with CRMX and dual Ethernet network port. 53 types of lighting modes: CCT mode, Source Matching mode, and Effects mode. ·CCT Mode: Adjust the light’s intensity and color temperature as needed. ·Source Matching Mode: This mode can only be accessed through the APP. Choose from 12 simulated light sources: Tungsten, HMI5600, HMI6000, Studio Lamps, Sodium Lamp, Halogen, Arc Lamp, Candle, Sunset/Sunrise, Daylight, Overcast Sky, CFL Cool White. ·Effects Mode: This mode can only be accessed through the APP / DMX / CRMX / Network port. Choose from 12 simulated light effects: Lightning, CCT Loop, Candle, Bad Bulb, TV, Paparazzi, Explosion, Pulsing, Strobe, Fire, Fireworks, Welding. We firmly believe that, proper use of this product will greatly enhance your production workflow. We strongly recommend reading the following user guide carefully before using the product.
DISCLAIMERS
1Before using this product, please read the text carefully to ensure that the correct operation of the product has been carried out. Failure to follow and not following the instructions and warnings in this document may cause harm to you and others around you, or even damage the product or other surrounding items.
2By using this product, you are deemed to have carefully read the disclaimer and warning, understand and acknowledge all the terms and contents of this statement, and promise to take full responsibility for the use of this product and the possible consequences.
3Design and specifications are subject to change without notice.
3
PRODUCT PARAMETER
Brand : GVM Product Model : GVM R1200B Product Name : LED Video Light Product Type : COB Point Source Light Features : CCT / Source matching / Efficacy mode, Brand-new LCD screen, High color
rendering index LED light engine, Support for RDM
Control Methods : On board control, GVM Mesh Bluetooth APP control, DMX/RDM
control, LumenRadio CRMX, Art-Net
Ingress Protection Rating: Ip65 Bluetooth Controllable Distance : 100M Color Rendering Index : 97 Color Temperature : 2700K~6800K Illumination : 9360 lux@3m, 3450 lux@5m; LED Chip Quantity : 1 (COB light Chip) Light Adjustment Method : Step-less adjustment Power : 1200W Product Net Weight : 12.5 KG(incl. yoke), 10.6 KG(excl. yoke) Product Size (mm) : 644×364×290(incl. yoke), 396×312×290(excl. yoke) Controller Weight: 4.5KG Controller Dimensions (mm) : 146×167×328 Connection Cable: 7-Pin waterproof cable (5m) Power Cord: Self-locking three-core rubber power cord (6m) Power Supply Mode: AC input Voltage: AC100-240V, 50-60Hz Cooling : Heat Sink Radiating + Cooling Fan Product Material : Aluminum alloy + Plastic Commodity Origin : Huizhou. China
4
PRODUCT STRUCTURE DIAGRAM
Carry Handle GVM G Mount Light Engine
GVM G mount release button 1/4”-20 Secure Screw Junior Pin (1.125in/28mm)
Heat Dissipation Vent
7-Pin Weatherproof Head Cable Connector U-shaped Yolk
Ratcheting Disk Brake Handle
5
Power input Controller output
LAN2 LAN1
CRMX antenna Bluetooth antenna
USB Port DMX input DMX output
Display screen Mode key Menu key Return key
Knob : Brightness adjustment /
selection confirmation
Lock key Power ON/OFF Button
Knob : CCT adjustment
6
INSTALLATION METHOD
1 Slide the 5/8″ receiver over the spigot/stud at the top of the light stand. Lower it fully down so the receiver fits snugly onto the stand. Tighten the securing knob on the yoke. Make sure the light does not wobble or spin.
2 Loosen the angle locking handle on the side of the yolk then adjust the tilt angle of the light to your needs, and then tighten the angle locking handle.
7
3 Installation and detach of the GVM G mount reflector: (The GVM G mount reflector needs to be purchased separately.) Installation: Match the three prongs (lugs) on the reflector with the notches on the light’s GVM G mount. Insert the reflector by pushing it straight in so the prongs slide into the corresponding notches. Once inserted, rotate the reflector clockwise. You should feel or hear a “click” or “snap” when it locks in place. Tighten the locking screw located in the lower right corner with a hex key to firmly attach the GVM G reflector in place.
Tighten the locking screw
Detach: First, use a hex key to loosen the locking screw at the lower right corner Press and hold the release latch and rotate the G-7 reflector counterclockwise, After twisting, pull the reflector straight out from the mount.
Loosen The Locking Screw
Reflector Release Latch 8
4 Disassemble the light from the U-shaped yolk: Press the release mechanism on both side of the yolk, then pull the light straight up to remove it from the frame.
Installing the light to the U-shaped yolk: Align the grooves on both side of the yolk, Insert the light from top to bottom into the yolk until the lock of the U-frame automatically locks.
9
5 Attach the super clamp onto a light stand as shown in the figure below.
6 As shown in the figure below, to attach the controller onto the super clamp. First push in the release lever to prep the quick-release plate. Then slide the Control Box onto the locking plate (the release lever will spring back to lock the control box in place.) Make sure to check that it is secure.
10
7 As shown in the figure below, connect the head cable from the light to the controller. 11
8 Use the AC power cord to connect the control to the power supply.
PowerInputPort 12
DESCRIPTION OF PRODUCT CONTROL KEYS
1 Display screen Display the current Settings, modes and parameters.
2 Mode key: Enter the CCT dimming mode.
3 Menu key: Enter the system menu Settings.
4 Back key: Return to the previous level menu.
5 Lock key: Press and hold for 2 seconds to lock/unlock. When locked, the buttons and knobs will not be unavailable.
6 Knob : When setting the menu Rotate the KnobSelect the menu / Set parameters; Press the knob brieflyConfirm the selection / enter the menu. In CCT mode Rotate the KnobFine-tune the brightness level of the light; Press the knob brieflyQuickly adjust the brightness level in 25% increments.
7 Knob : Rotate the KnobFinely adjust the color temperature of the light; Press the knob brieflyQuickly adjust the color temperature of the light in 25% increments.
8 Power ON/OFF key: Press this key to power ON/OFF.
1 2345
6
7
8
13
FUNCTION INTRODUCTION & INSTRUCTIONS FOR USE
MENU Press the [Menu] button to enter the menu settings interface Rotate [Knob 1] to select a menu category Press [Knob 1] to enter the selected menu’s settings interface Press the [BACK] button to return to the previous menu level.
Menu
DMX Settings
DMX Settings Navigate to the [Address / Signal Loss / Mode] option using [Knob 1], then press [Knob 1] to enter. In the submenu: Address: Set the desired DMX address by rotating [Knob 1]. Signal Loss: Define the device behavior when DMX signal is lost, and press to confirm. Mode: Choose the appropriate DMX working mode, and confirm the selection.
DMX Settings
Address
001
Loss Signal
Modes
DMX Settings
Hold last Command Black Out Fade Out Fade Out After 2 min
DMX Settings
CCT 8-bit(2ch) CCT 16-bit(4ch) CCT+Ctrl 8-bit(4ch) CCT+Ctrl 16-bit(6ch)
DMX Settings
FX 8-bit(7ch) FX 16-bit(10ch) FX+Ctrl 8-bit(8ch) FX+Ctrl 16-bit(11ch)
Dimmer Curve Rotate [Knob ] and select [Linear/Log/Exp/S-Curve] Press [Knob ] to confirm the selection.
Dimmer Curve
Linear Exp
Log S-Curve
14
Frequency Settings Rotate [Knob ] to set the light frequency.
Frequency Settings
0000 Hz
Studio Mode Rotate the knob to select [ON/OFF] Press [Knob ] to confirm the selection. ON: When the Studio mode is turned on, the settings you have made will be applied the next time you power on the unit. OFF: When the Studio mode is turned off. The light will go back to its default settings after powering on the next time.
Studio Mode
Studio Mode
ON
OFF
Control Mode Navigate to [Bluetooth / CRMX / Ethernet / Art-Net] using [Knob 1], then press to enter the desired menu. In each submenu: Bluetooth: Enable or disable Bluetooth signal (ON/OFF) and perform a Bluetooth reset. CRMX: Enable or disable CRMX and optionally disconnect any existing link. Ethernet: Configure the network settings including IP address, subnet mask, and default gateway. Art-Net: Set the necessary Art-Net network parameters for communication.
Control Mode
Bluetooth CRMX Ethernet Art-Net
Bluetooth
Bluetooth
CRMX
Bluetooth
ON
Bluetooth
OFF
CRMX
ON
Bluetooth Reset
Bluetooth Reset
Unlink
CRMX
Ethernet
CRMX Unlink
OFF
IP Addtess 192 168
1
2
Art-Net Port
0
Subnet Mask 255 255 255
0
Art-Net Sub-Net
0
Gateway
192 168
1
2
Art-Net Net
0
MAC: 88:68:4B:4F:01:11
Art-Net Univers
0
15
Fan Mode Rotate [Knob ] and select [Smart/High/Silent] Press [Knob ] to confirm the selection. Smart: Adjust the fan speed as the temperature changes. High: The fan operates at the maximum rotational speed. Silent: The silent mode will stop the fan from rotating and reduce the light output power to 150W. It is not recommended to use this mode for a long period of time.
Fan Mode
Smart High Silent
System language Rotate [Knob ] and select [English/ ] Press [Knob ] to confirm the selection.
Language
Address
System Settings Rotate [Knob ] and select [About/Update Firmwate/Factory Reset] Press [Knob ] to enter the selection. About: Check the model, firmware version and product UID. Update Firmwate: After inserting the USB flash drive with the new firmware, select either [Upgrade Controller] or [Upgrade Lamp]. Factory Reset: Rotate and press [Knob ], then set [Confirm/Cancel] to restore factory Settings.
System
About Update Firmwate Factory Reset
About
Product Modle Lamp Version Controller Version Product UID
R1200B 1.06 1.20 7783DC4F
Update Firmware
Upgrade Controller Upgrade Lamp *Please make sure to insert the U disk with the new firmware.
Factory Reset
RESET
Confirm
Cancel
16
Status indication specification
Dimming curve: Linear
Dimming curve: Exp
Fan mode: Smart
Dimming curve: Log
Dimming curve: S
Fan mode: High
Bluetooth connected
Fan mode: Silent
DMX mode is enabled and the DMX console is connected. When the lock mode is enabled, the buttons and knobs will be unavailable.
CCT(MODE) Press the [MODE] key to enter the [CCT] adjustment interface. INT: Rotate [Knob ] to adjust the intensity parameter of the light; Press the [Knob ] key to quickly switch the brightness level (0, 25, 50, 75, 100). CCT: Rotate [Knob ] to adjust the color temperature parameter of the light; Press the [Knob ] key to quickly switch the color tempreture (2700, 3200, 4300, 5100, 5600, 6800).
CCT
INT 10.0% CCT 5600K
:001 T: 35.0
Source matching mode:
The source matching mode can only be accessed through the APP. This mode has 12 simulated light sources. Tungsten, HMI5600, HMI6000, Studio Lamps, Sodium Lamp, Halogen, Arc Lamp, Candle, Sunset/Sunrise, Daylight, Overcast Sky, CFL Cool White.
Effect mode:
The effecThe effect mode can only be accessed through the APP. This mode has 12 simulated light effect. Lightning, CCT Loop, Candle, Bad Bulb, TV, Paparazzi, Explosion, Pulsing, Strobe, Fire, Fireworks, Welding.
17
APP CONTROL
APP Download Method (Scan the QR code on the back of the manual to download the APP)
Android DeviceOfficial website QR code, Google Play, Huawei Store, etc.
iOS DeviceApp Store
Figure 1
Figure 2
Device-adding
1Before adding a device, please make sure you have turned on your phone’s Bluetooth and network data, accessibility to Bluetooth and network data, then reset the lighting device’s Bluetooth.
2Click the “Add Device” button on the “My Devices” page to find the Bluetooth light devices that have been turned on nearby. (Figure 1)
My Devices Ble Devices
Searching for nearby ble devices… SigMesh Ble Devices
Add Device
SigMesh Groups Create Group
SigMesh Light programming Add lighting effect program
My Devices New Devices Bluetooth devices nearby
GVM-XXXXXX
3Select the device to be connected for pairing. (Figure 2)
Start Connecting
* Android requires location permissions to be turned on in order to connect your device using mesh technology, and we do not collect any of your location information during this process.
Figure 3
My Devices Ble Devices
Searching for nearby ble devices… SigMesh Ble Devices
GVM-XXXXXX
Figure 4
My Devices GVM-XXXXXX
My Preset
Manage
Device Management
1After successfully adding your lighting device, your device will be displayed in the “My Devices” list. (Figure 3)
Add Device SigMesh Groups
Creat Group SigMesh Light programming
Add lighting effect program
2Click on the Device to access the device control. (Figure 4)
18
Account Login
Figure 5
Use e-mail to get the verification code to log in (the first login automatically registers the account). (Figure 5)
There may be a delay in sending the verification code, and the speed of delivery depends on the e-mail server you are using.
My Devices
Verification Code Login
Auto registration for the first login
Email Verification code
Get code
Some email servers may recognize our verification emails as advertising promotions, please check your spam folder/inbox.
Login Password Login
After logging in, you can synchronize the Mesh Bluetooth devices bound to the current account to other smart devices.
Cannot get the code, please contact: Online Service
USE AND PRESERVATION
Do not place the product in a high humidity, strong electromagnetic field, direct sunlight, or high-temperature environment. If the product will not be used for a long time, please disconnect its power. Cleaning: Unplug the power before cleaning. Use a dry cloth only–avoid cleaning agents or solventbased liquids, as they may damage the surface. Power: Make sure the power is within the demanded range, not too high or too low. Repairing: If there is a fault or performance degradation, do not unpack the shell by yourself, avoiding damage to the machine and losing the right of maintenance. When there is a fault, do not hesitate to contact us, and we will do our best to deal with the problem. Accessories: Please use the accessories provided by the manufacturer and approved ones, to maximize the performance. Warranty: Do not modify the product, or you will lose the right to maintenance.
19
QUICK TROUBLESHOOTING
Issue
Check
Troubleshooting
After powering on, the green light on the power button flashes, there is a display on the screen, but the light does not turn on.
This malfunction is a communication Unplug the connectors at both
error reminder between the controller ends of the cable, then reinsert
and the lamp body due to an abnormal them into the corresponding
cable connection. You need to check female connectors on the controller
whether the connectors at both ends of and the lamp body.
the cable are properly plugged in.
When AC power is This malfunction is actually a feature of the Check the `Studio’ mode status in
supplied without pressing `Studio’ mode, where the device powers on the controller’s settings menu, and
the switch, the light turns automatically when connected to power. set it to `Off’ to disable it.
on automatically.
The app cannot find the device via Bluetooth.
1. Check whether the Bluetooth function is
enabled on both the phone and the
device. Ensure the distance between the 1. Turn on Bluetooth on both the
phone and the device is appropriate, device and the phone, and
and check whether there are any walls ensure they are within effective
or obstacles that might interfere with range of each other.
the signal.
2. Reset the device’s Bluetooth.
2. Make sure the device is not already
connected to another phone.
The APP failed to connect to the device.
Ensure there is an appropriate distance Move the phone closer to the
between the device and the phone, and device to ensure an effective
check whether any walls or obstacles are connection range.
blocking the signal.
The console cannot find the CRMX device.
1. Navigate to the Settings Menu
1. Check whether the CRMX function is on the device controller and
enabled on the device.
enable the CRMX function.
2. Check whether the CRMX on the device 2. In the same menu, reset the is already connected to another console. CRMX configuration to clear any previous connections.
20
PACKING LIST
Name
Quantity
LED Video Lights
1
Power Cord
1
Lamp head protective cover
1
Carrying Case
1
Notes
PRECAUTIONS
1Please use the matching power adapter the same specification to power the product. Do not use power adapter with different output voltage parameters.
2The product is not anti-corrosion, therefore do not let the product touch any corrosive liquid.
3When using the product, make sure the product is put firmly and prevents falling and damage.
4If the product will not be used for a long time, please switch off the power to reduce energy loss.
21
PRODUCT WARRANTY
Dear user, this warranty card is important proof for applying for warranty service. Please cooperate with the salesperson to fill it out and keep it properly. Thank you!
Product
Model Number
Information
Product Barcode
Name
Contact Number
User Information Mailing Address
Name
Seller Information
Contact Number Mailing Address
Sales Date
Remarks
Note: this form should be confirmed by the salesperson’s stamp.
Applicable Products
This document applies to the products listed in the relevant “Product Warranty Information” (see instructions below). Other products or components that do not fall within this scope (such as promotional products, gift items, and other components added after the factory) are not covered by this warranty promise.
Warranty Period
The corresponding warranty period for products and components shall be executed according to the relevant “Product Warranty Information”. The warranty period starts from the first day of purchase of the product, and the date of registration on the warranty card at the time of purchase shall prevail.
22
How to Obtain Warranty Service
You can directly contact the product salesperson or authorized service agency, or call GVM’s aftersales service hotline to contact us and have our service personnel arrange service for you. When applying for warranty service, you should provide a valid warranty card as a warranty certificate to be eligible for warranty service. If you cannot provide a valid warranty card, we may also provide you with warranty service under the circumstance that our products or components are confirmed to be within the warranty scope, but this is not our obligation.
Cases where warranty does not apply:
If the product meets the following conditions, the warranty and service under this document will not apply:
1The product or parts have exceeded the corresponding warranty period.
2Malfunctions or damages caused by incorrect or improper use, maintenance, or storage, such as improper handling, use for purposes other than the reasonable expectations of the product, incorrect insertion or removal of external devices, falling or crushing due to external force, or exposure to inappropriate temperature, solvents, acids, alkalis, water immersion, or damp environments.
3Malfunctions or damages caused by unauthorized installation, repair, modification, addition, or disassembly by institutions or personnel not authorized by GVM.
4Modifications, changes, or removals of the original identification information of the product or its parts.
5Lack of valid warranty card.
6Malfunctions or damages caused by the use of unauthorized, non-standard or non-publicly released software.
7Malfunctions or damages caused by force majeure or accidents.
8Other malfunctions or damages not caused by quality issues of the product itself. In such cases, you should seek solutions from the relevant responsible parties, and GVM will not be held liable. Malfunctions or damages caused by components, accessories, or software not covered by the warranty or beyond the warranty scope that renders the product unable to function properly are not covered by the warranty. Fading, wear, and consumption that is normal during the product usage process are not covered by the warranty.
Product Warranty and Service Support Information
The product warranty period and service types are implemented according to the following “Product Warranty Information” for each product category, component, and optional equipment:
Product Category
Accessories Name
Warranty Period(Month)
Warranty Service Type
Component Circuit Board.
12 Month Customer service repair
Other
Spotlight mount, softbox, adapter, Standard reflector, power cord, battery Handle, light stand, TYPE-C cable, battery slot, battery, Fresnel lens, grid, carrying bag and all other accessories, etc. Consumable or electrically sensitive parts are not covered by the warranty.
None
No Warranty
23
GVM Official website
Download APP
Huizhou Latu Film Equipment Co., Ltd.
Web: www.gvmled.com B&H Email: bh@gvmled.com GVM Email: support@gvmled.com Amazon Email: amazonsupport@gvmled.com
24 Warehouse Address: 12285 MCNULTY RD, STE 105 PHILADELPHIA, Pennsylvania 19154, USA
Documents / Resources
 |
B and H GVM R1200B Bi-Color LED Monolight [pdf] Instruction Manual GVM R1200B, GVM R1200B Bi-Color LED Monolight, Bi-Color LED Monolight, LED Monolight, Monolight |