Armatur Sensoru üçün Keilton Basic RM51 Uzaqdan İdarəetmə

Təsvir

The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.

Xüsusiyyətlər

• Aşağı enerji istehlakı.
• Infrared communication.
• Setting most of the Keilton Sensors G2.
• Custom Configurations can be saved to A, B, C, D, or For.
• 40′ maximum IR range.
• RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)

Spesifikasiyalar

Sifariş Məlumatı

Model	Təsvir
RM51.A0	Basic Sensor Controller RM51
RM51.A1	Basic Sensor Controller RM51 With RML

Sifariş Məlumatı - Aksesuarlar

Model	Təsvir
RML	Extended IR range for commissioning

Ölçülər

Məhsul Etiketi

Uzaqdan Təlimatlar

Yaddaş rejimi (istismar)
To begin commissioning, follow these steps:

1. Pro yaddaş seçinfile: A, B, C, D və ya E.
2. The remote’s indicator lights will flash, indicating the currently saved settings.
3. Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
4. Point the remote at the desired luminaire and press “SEND.”
5. The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
6. If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.

E Mode allows for visual adjustment to choose the desired dimming level.

Gün işığı yığımı (F rejimi)
Continuous Adjustment Mode adjusts dimming levels based on daylight.

1. Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
2. Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
3. Review the selected settings and make changes as necessary. Press “SEND.”
4. If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.

Əlavə Uzaqdan Funksiyalar

ON	Dönür ON işıqlar.
OFF	Dönür OFF işıqlar.
TEST	The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100%, Həssaslıq: Yüksək, Saxlama vaxtı: 2s, Standby dim: 50%, Gözləmə vaxtı: 2s.
RESET	Trim= 100%, Sensitivity = Yüksək, T1 = 5 dəq, Standby Dim = 30%, T2 = 60 dəq, Photocell = OFF.
DIM+/-	Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous qaralma
TRIM-SƏVİYYƏ	Set the Maximum brightness.
Həssaslıq	Set the motion sensitivity of the sensor AŞAĞI:50% / YÜKSƏK:100%, QAPALI: disable the motion detection function.
GÖZLƏMƏ MÜDDƏTİ	Gözləmə rejiminə keçməzdən əvvəl boşluq aşkarlanmadan keçən müddət.
GÖZLƏMƏ DURANI	Select any standby dim level.
Gözlə TIME	Standby time, when the time is set to “∞”, the daylight detection function is activated.
Fotosell	visible light threshold, the fixture is allowed to be turned on when it falls below the threshold AŞAĞI:5fc / YÜKSƏK:20fc, KAL: Collect the current visible light illuminance as the threshold, QAPALI: disable PHOTOCELL function.
MODE	Default configuration parameters for modes A üçün F.
GÖNDƏR	Parametrləri sensora göndərin.
DEFAULT Rejim A	Trim= 100%, Sensitivity = Aşağı, T1 = 30 dəq, Standby Dim = 50%, T2 = ∞, Photocell = KAL.
DEFAULT MODE B	Trim= 100%, Sensitivity = Aşağı, T1 = 30 dəq, Standby Dim = 50%, T2 = 15 dəq, Photocell = KAL.
DEFAULT MODE C	Trim= 100%, Sensitivity = Aşağı, T1 = 30 dəq, Standby Dim = 50%, T2 = 15 dəq, Photocell = OFF.
DEFAULT REJİM D	Trim= 50%, Sensitivity = Aşağı, T1 = 30 s, Standby Dim = 50%, T2 = 30 dəq, Photocell = KAL.
DEFAULT REJİM E	Manual Dimmer Mode, Trim 100%.
DEFAULT REJİM F	Daylight Harvesting, Trim= 50%, Sensitivity = Aşağı, T1 = 15 dəq.

Bizimlə əlaqə saxlayın

• 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
• T: +1 443-320-2233 (M-F 9 am-5 pm ET)
• E: support@autani.com

Tez-tez verilən suallar

How do I change the memory profile parametrlər?

Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save

Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?

No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.

What is the expected operation if the user sets Standby Time to something other than INFINITE?

moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.

If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?

The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.

Sənədlər / Resurslar

Armatur Sensoru üçün Keilton Basic RM51 Uzaqdan İdarəetmə [pdf] İstifadəçi Təlimatı RM51.A0, RM51.A1, RM51 Armatur Sensoru üçün Uzaqdan İdarəetmə, RM51, Armatur Sensoru üçün Uzaqdan İdarəetmə, Armatur Sensoru üçün, Armatur Sensoru

İstinadlar

• İstifadəçi təlimatı