AXXESS AXPIO-STY1 Dash Kit and Harness Instruction Manual

Remove a screw from the left side of the panel below the steering column.
Using a panel removal tool, carefully unclip and remove the centre console cover.

Unsnap and remove the panel above the glove box.

Dash Disassembly

Remove a 7mm screw and remove the small trim next to the left center vent.
Remove 2 screws from the radio/climate control panel, then unclip and remove the panel.

Extract 3 screws from each A/C vent and remove the vents.
Remove 4 screws securing the factory radio, disconnect the wiring, and then remove the radio.

Remove 2 screws and remove the CD player.

Dash Disassembly with LD-LAN09-PIO

Using a panel removal tool, unclip the plastic shroud around the steering wheel column.
Connect the LD-GMSWC to the 10-pin straight row connector located in the steering column.

Route the LD-GMSWC cable through the steering column into the dash and back towards the radio area.
Remove 3 bolts from the lower trim cover. Rotate the steering wheel to gain access to the bolts, then remove the forward-facing bolts.

KIT FEATURES

Designed for Pioneer DMH-W4600NEX/W4660NEX or DMH-WC5700NEX receivers
Allows for the retention and adjustment of the factory personalisation menu through the Pioneer radio

Provides a visual view of HVAC and gauges on the Pioneer screen (cannot be adjusted via the screen)

KIT COMPONENTS

A) Radio housing trim panel

B) Brackets
C) Trim panel bracket

D) Pocket
E) #8 x 3/8″ Truss-head Phillips screws (4)

Not Shown: Radio Interface, LD-GMLAN09-PIO, LD-BACKCAM-MOST, LD-GMSWC, AD-EU5, 40-GPS-PIO, PR04AVIC-PIO / PRO4-PIORCA, LD-AX-SPK, AXUSB-GM6
Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle-specific applications.

WIRING & ANTENNA CONNECTIONS (sold separately)

RGB Extension Cable: Pioneer part # CD-RGB150A (not sold by Metra)

TOOLS REQUIRED

Panel removal tool
Phillips screwdriver
9/32″ socket wrench
ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product.
Ensure that all installation connections, especially the airbag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product.

KIT FEATURES

Complete Plug-n-Play installation
Includes dash kit with Axxess interface and vehicle-specific T-harness
Includes a 3′ USB/AUX/HDMI replacement cable with panel
Includes a radio antenna adaptor for GPS
Provides accessory power (12-volt 10-amp)
Provides NAV outputs (parking brake, reverse, speed sense)
NOTE: Refer also to the instructions included with the aftermarket accessory before installing this device.

Retains audio controls on the steering wheel
Works in both single and dual-zone vehicles
Retains safety chimes through an included off-board speaker

USB Micro “B” USB updatable
Dash kit is painted scratch-resistant matte black to match the factory finish
For non-amplified vehicles only

SPEAKER INSTALLATION

Install the provided speaker in the dash before assembling the radio components.
Note: Make sure this is mounted in a location suitable for the driver to hear. (The audio level for the speaker can be changed via the radio once installed.)

DASH DISASSEMBLY

Unsnap and remove the panel above the radio screen. (Figure A)

Unsnap and remove the trim panel located at the driver’s side edge of the dash. (Figure B)
Remove (1) screw from left side of panel below steering column. (Figure C)
- Note: The panel does not need to be fully removed.

Using the panel removal tool, carefully unclip and remove the centre console cover. (Figure D)
Unsnap and remove the panel above the glove box. (Figure E)
Remove (1) 7mm screw and remove the small trim next to the left center vent. (Figure F)
- Note: Next to the push-to-start button in some models.
Remove (2) 7mm screws from the radio/climate control panel, then unclip and remove the panel. (Figure G)
Extract (3) 7mm screws from each A/C vent and remove the vents. (Figure H)

Remove (4) screws securing th factory radio, disconnect the wiring, and then remove the radio. (Figure I)
Remove (2) 7mm screws and remove the CD player. (Figure J)

If using the LD-LAN09-PIO:

Using the panel removal tool, unclip the plastic shroud around the steering wheel column. (Figure A)
Connect the LD-GMSWC to the 10-pin straight row connector located in the steering column.
Route the LD-GMSWC cable through the steering column into the dash and back towards the radio area.

Remove 3 three bolts from the lower trim cover. Rotate the steering wheel to gain access to the bolts, then remove the forward-facing bolts. (Figure B)
- NOTE: If RPO is IO5 or IO6, use the LD-LAN09-PIO.
- If RPO is IOB, use the LD-LAN10-PIO.

CONNECTIONS

KIT ASSEMBLY

Double DIN radio provision

Attach the radio brackets to the radio trim panel with (4) #8 x 3/8″ Phillips screws provided with this kit. (Figure A)

Slide the radio into the bracket trim panel assembly and secure with the screws supplied with the radio. (Figure B)
Clip the climate controls into the radio trim panel assembly.
Snap the climate control vents into the radio trim panel assembly.

Locate the factory wiring harness and antenna plug in the dash. Metra recommends using the proper mating adapters from Metra and/or AXXESS.
Complete all connections to the radio and vehicle, reconnect the negative battery terminal, and then test the aftermarket radio and vehicle for proper operation.
Mount the radio assembly into the dash using the factory screws.

Reassemble the dash in the reverse order of disassembly to complete the installation.

RADIO OPERATIONS

Vehicle Selection

Allows the selection of the vehicle the Pioneer radio is being installed in.

Select Make, Model and Trim to activate the extended functions of the radio.
The vehicle type must be selected to activate iPod, Bluetooth, backup cameras, as well as HVAC functions and steering wheel controls.
Press Confirm to lock in the selection.

Car Features

The source for accessing all vehicle information and options.

Customisations Menu:

Allows full control of vehicle personalisation options.
Access this menu by selecting the gear icon on the previous screenshot
Provides Steering Wheel Control (SWC) Configuration.

Dual Assignment: Assign (2) functions to a single SWC button.
Remap: Reassign a button on the SWC.

Vehicle Information Screen

The source for accessing all vehicle information and options.

Climate Screen

Climate Screen: HVAC Status onlyhvac Status only

Radio ID Screen

Feedback screen for interface software information.
Helpful information for troubleshooting.

Customer Service

Having difficulties? We’re here to help.
Contact our Tech Support line at: 3862571187
Or via email at: techsupport@metra-autosound.com

Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM – 5:00 PM

Sunday: 10:00 AM – 4:00 PM
Metra recommends MECP-certified technicians
AxxessInterfaces.com

FAQ

Q: Is it necessary to disconnect the negative battery terminal before installing this product?
- A: Yes, it is important to disconnect the negative battery terminal with the key out of the ignition before installation.

Documents / Resources

AXXESS AXPIO-STY1 Dash Kit and Harness [pdf] Instruction Manual
AXPIO-STY1, AXPIO-STY1 Dash Kit and Harness, Dash Kit and Harness, Kit and Harness

References

User Manual

AXXESS AXPIO-STY1 Dash Kit and Harness

Product Information

Product Usage Instructions