AXXESS AXPIO-IN1 Infinity G37 Radio Installation Kit Installation Guide

Retains use of the factory climate control panel
Allows visual of HVAC and gauges and adjustment of HVAC functions and factory personalization through the Pioneer screen

Painted scratch resistant matte black
Retains factory back up camera

Retains audio controls on the steering wheel
Supported Languages include English, Spanish and French

KIT COMPONENTS

A) Upper panel

B) Upper brackets
C) Lower brackets

D) Modular screen brackets
E) Panel clip mounts

F) White panel clips (2)
G) #8 x 3/8” truss-head Phillips screws (2)

Not shown: Antenna adapter and harnesses

Product Info

WIRING & ANTENNA CONNECTIONS

Wiring Harness: Included with kit
Antenna Adapter: 40-NI12 Included with kit

TOOLS REQUIRED

Panel removal tool

Phillips screwdriver
Socket wrench

ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product.
NOTE: Refer also to the instructions included with the aftermarket radio.

DASH DISASSEMBLY

2008-2009 vehicles:

Slide the shifter boot down and remove clip holding shifter knob and remove shifter knob. (Figure A)
Unclip and remove shifter boot trim panel. (Figure B)

2010-2013 vehicles:

Unclip and remove the trim panel from below the factory radio controls. (Figure A)

2008-2013 vehicles:

3. Remove (2) screws at the bottom of the radio/climate control panel and remove panel. (Figure C)

4. Remove (2) screws at the bottom of the factory display panel and remove panel with the vents. (Figure D)

5. Remove the factory vents and save them for Kit Assembly.

6. Remove (4) Phillips screws securing the radio chassis and A\C amp bracket assembly then remove the assembly from the dash. (Figure E)

7. Remove (2) Torx screws securing the A\C amp module to the radio chassis/ bracket assembly and save for Kit Assembly. (Figure F)

KIT PREPARATION

Snap the factory vents into the upper panel. (Figure A)
Remove the (2) top corner screws from the factory climate control panel.
Attach the panel clip mounts to the factory climate control panel using the factory screws. (Figure B)
Attach the white plastic panel clips to the panel clip mounts. (Figure C)

KIT ASSEMBLY

Modular radio mounting

Secure the Pioneer radio chassis and the factory AC amp to the lower brackets using the screws supplied with the Pioneer radio and the factory AC amp screws. (Figure A)
Secure the modular screen to the modular screen brackets using the screws supplied with the Pioneer radio. (Figure B)

See AXXESS wiring section page 9.
Plug the Pioneer extension cable to the Pioneer chassis.
Secure the radio chassis/ AC amp assembly to the dash using only the bottom two factory screws (the upper two will come after the upper assembly).
Note: While installing, route the Pioneer extension cable up to upper dash location. (Figure C)

Plug extension cable into the modular screen and secure it to the dash using the factory hardware. (Figure D)
Connect the hazard and secure the upper panel to the dash using the factory hardware. (Figure E)
Plug in the factory climate control and secure at the bottom with the two #8 truss head screws supplied. (Figure F)

Snap the factory bottom trim panel in place. (Figure G)

Shallow mount radio

Secure the factory AC Amplifier Module to the lower brackets using the factory AC amp screws. (Figure A)

Secure the shallow mount radio to the upper brackets using the screws supplied with the Pioneer radio.
See AXXESS wiring section page 9.
Secure the AC amp assembly to the dash using only the bottom two factory screws (the upper two will come after the upper assembly). (Figure C)

Plug the shallow mount radio in and secure to the dash with remaining two factory screws from step 8. (Figure D)
Connect the hazard wiring and secure the upper panel to the dash using the factory hardware. (Figure E)
Plug in the factory climate control and secure at the bottom with the (2) #8 truss head screws supplied. (Figure F)

Snap the factory bottom trim panel in place. (Figure G)

AXXESS INTERFACE INSTALLATION

INTERFACE FEATURES

Designed for non-amplified and amplified vehicles

Complete plug-n-play installation
Allows visual of HVAC and gauges and adjustment of HVAC functions through Pioneer® screen
Allows for the retention and adjustment of the factory personalization menu through the Pioneer® radio.

Retains factory back up camera
Retains factory AUX in
Retains audio controls on the steering wheel

Provides accessory power (12V 10-amp)
Provides NAV outputs (parking brake, reverse, and speed sense)
Retains safety chimes through an included off-board speaker

Includes radio antenna adaptor for GPS
Micro “B” USB updatable

INTERFACE COMPONENTS

Radio interface
2008-2013 NON-NAV car side harness (LD-NIS2-PIO )
2010-2013 NAV Models (LD-NISNAV2-PIO)

2008-2009 NON-NAV models (LD-NISNAV1-PIO)
12V to 6V camera step down (AXCSD-6V)
Pioneer Harness (PR04AVIC-PIO)

Pioneer Low-Level Output Harness (PR04-PIORCA)
External Speaker (Warning Chime Speaker)

Please Note: Supported Languages include English, Spanish and French

TOOLS REQUIRED

Crimping tool and connectors, or solder gun, solder, and heat shrink
Small flat blade screwdriver

Tape
Wire cutter
Zip-ties

2008-2013 NON-NAV MODELS (LD-NIS2-PIO)

2010-2013 NAV MODELS (LD-NISNAV2-PIO)

2008-2009 NON-NAV MODELS (LD-NISNAV1-PIO)

RADIO OPERATION

Vehicle Selection – Allows you to select the vehicle the radio is being installed in.

Vehicle type must be selected to activate menu & HVAC functions, as well as steering wheel controls. Press Make to change the vehicle type. Then press Confirm. The radio will then reset and lock in the selected vehicle.

Car Features – The source for accessing all vehicle information and options.

HVAC Operation – HVAC Status and Control Screen.

Vehicle Info Screen – Displays various information of the vehicle (TPMS, Park Position, Lights).

Customizations Menu – Allows full control of vehicle personalization options.

Access this menu by selecting the gear icon on the previous screenshot.

About Screen – Feedback screen for interface software information.

AXPIO-IN1
INSTALLATION INSTRUCTIONS

Having difficulties? We’re here to help.

Contact our Tech Support line at:
386-257-1187

Or via email at:
techsupport@metra-autosound.com

Tech Support Hours (Eastern Standard Time)

Monday – Friday: 9:00 AM – 5:00 PM
Saturday: 10:00 AM – 5:00 PM
Sunday: 10:00 AM – 4:00 PM

Metra recommends MECP certified technicians

Documents / Resources

AXXESS AXPIO-IN1 Infinity G37 Radio Installation Kit [pdf] Installation Guide
AXPIOIN1, 086429428045, AXPIO-IN1 Infinity G37 Radio Installation Kit, AXPIO-IN1, Infinity G37 Radio Installation Kit, G37 Radio Installation Kit, Radio Installation Kit, Installation Kit, Kit

References

User Manual