AVTechsmart-LOGO

AVTechsmart miniRETROB100L Light

AVTechsmart-miniRETROB100L-Light-product-image

Product Information

The miniRETROB100L is a high temperature indoor lighting lamp. It features built-in programs, manual mode function, and sound control function. The lamp has a DMX mode with 1 channel and 6 channel options. It also has a pixel control feature for precise control over the lighting effects. The product dimensions are provided in the product dimension drawing.

Safety Instructions

  • Do not touch the lamp body when working to avoid burns.
  • Maintain a 50CM space at the back of the lamp body for heat dissipation.
  • Turn off the lamp power when installing or replacing the lamp tube.
  • This lamp is for indoor use only and is not waterproof.
  • Ensure that the voltage and frequency of the power supply match the requirements of the device.
  • Do not operate the equipment if there is wire damage or wear.
  • Do not remove any part of the equipment during use.
  • Any unauthorized modification to the product will void the warranty.

Function Menu
The function menu provides access to different working modes and functions of the lamp.

Function Operation
Built-in Program Automatic Function

  1. Select the working mode menu.
  2. Select automatic mode.
  3. Choose one of the fifteen programs.
  4. Set the program speed.

Manual Mode Function
The manual mode function is consistent with the Pixel control 7CH channel. In manual mode, DMX address is not working.

  1. Select the working mode menu.
  2. Select manual mode.
  3. Choose one of the seven functions corresponding to the sub-menus.

Sound Control Function

  1. Select the working mode menu.
  2. Select automatic mode.
  3. Choose one of the nine programs.
  4. Select the working mode menu again.
  5. Select sound control mode.
  6. Set the sound control sensitivity. Voice control does not work from 0 to 15, and becomes more sensitive from 16 to 255.

Channel Function
The lamp has DMX general functions with 1 channel and 6 channel modes.

1CH DMX General Function

  1. Select the working mode menu.
  2. Select DMX mode.
  3. Set to 1 channel mode.
  4. Exit the working mode menu, select the DMX menu, and set the DMX menu address. The DMX address can be set to 001.

6CH DMX General Function

  1. Select the working mode menu.
  2. Select DMX mode.
  3. Set to 6 channel mode.
  4. Exit the working mode menu, select the DMX menu, and set the DMX menu address. The DMX address can be set to 001.

Note: The channel functions specify different features and settings based on the range of values.

Safety Notes

Note : To ensure reasonable consistency of operation, please read this instruction carefully. Any damages caused by the non- observance of this manual or any unauthorized modification to this product are not be subject to warranty .

  1. This product belongs to high temperature products. Do not touch the lamp body when working, carefully scalds!
  2. Maintain a 50CM space at the back of the lamp body for dissipate heat.
  3. When installing/replacing the lamp tube, turn off the lamp power!
  4. This lamp is used for indoor lighting, not waterproof ! When lamp works, lamp tube at high temperature.
  5. Make sure the voltage and frequency of power supply match the power require of this devise.
  6. Please do not operate the equipment in the condition of wire damage or wear.
  7. Do not remove any part of the equipment during the use of lamps.
  8. Any unauthorized modification to this product are not be subject to warranty .

Function MenuAVTechsmart-miniRETROB100L-Light-01Function Operation

AVTechsmart-miniRETROB100L-Light-02

Keys diagram

built-in program Automatic function

  1. Select the working mode menu.
  2. Select automatic mode.
  3. Choose one of fifteen programs.
  4. Setting program speed.

manual mode function
The manual mode function is consistent with the Pixel control 7CH channel but in manual mode DMX address is not working in that condition . The seven sub-menus correspond to seven functions .

Sound control function

  1. Select the working mode menu.
  2. Select automatic mode. Because sound control is based on the automatic program, so you need to choose the automatic program before you turn on the sound control .
  3. Choose one of nine programs .
  4. Select the working mode menu.
  5. Select sound control mode.
  6. Set the sound control sensitivity. 0-15 voice control does not work. From 16 to 255 sound control will more and more sensitive .

Channel Function
1CH DMX general function

  1. Select the working mode menu.
  2. Select DMX mode.
  3. Set to 1 channel mode.
  4. Exit the working mode menu, select the DMX menu, and set the DMX menu address.
    The DMX address can be set to 001.
Channel Function From To Feature
1 Dimmer 0 000 No function
1 255 Master dimmer

6CH DMX general function

  1. Select the working mode menu.
  2. Select DMX mode.
  3. Set to 6 channel mode.
  4. Exit the working mode menu, select the DMX menu, and set the DMX menu address.
    The DMX address can be set to 001.
Channel Function From To Feature
1 Dimmer 0 255 Brightness 1—100%
 

 

 

 

2

 

 

 

 

Strobe

0 3 No function
4 7 Dimmer
8 76 Synchronizing strobe;

Strobe from slow to fast

77 145 Pulse strobe ;

Strobe from slow to fast

146 215 Random strobe ;

strobe from slow to fast

216 255 Dimmer
 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

Auto run-1

0 15 No function
16 31 Program 1
32 47 Program 2
48 63 Program3
64 79 Program4
80 95 Program5
96 111 Program6
112 127 Program7
128 143 Program8
144 159 Program9
160 175 Program10
176 191 Program11
192 207 Program12
208 223 Program13
224 239 Program14
240 255 Program15
 

 

 

 

 

 

 

 

 

4

 

 

 

 

 

 

 

 

 

 

Auto run-2

0 15 No function
16 31 Program 16
32 47 Program 17
48 63 Program18
64 79 Program19
80 95 Program20
96 111 Program21
112 127 Program22
128 143 Program23
144 159 Program24
160 175 Program25
176 191 Program26
192 207 Program27
208 223 Program28
224 239 Program29
240 255 Program30
 

5

 

Speed

0 000 No function
1 255 Program speed from slow to fast
 

6

 

Sound

0 000 No function
1 255 Sensitivity increases gradually

7CH DMX Pixel Control function

  1. Select the working mode menu.
  2. Select DMX mode.
  3. Set to 7 channel mode.
  4. Exit the working mode menu, select the DMX menu, and set the DMX menu address.
    The DMX address can be set to 001
Channel Function From To Feature
1 LED 1 0 No function
1 255 Brightness 1—100%
2 LED 2 0 No function
1 255 Brightness 1—100%
3 LED 3 0 No function
1 255 Brightness 1—100%
4 LED 4 0 No function
1 255 Brightness 1—100%
5 LED 5 0 No function
1 255 Brightness 1—100%
6 LED 6 0 No function
1 255 Brightness 1—100%
 

7

 

LED 7

0 No function
1 255 Brightness 1—100%
8 Dimmer 0 255 Brightness 1—100%
 

 

 

 

9

 

 

 

 

Strobe

0 3 No function
4 7 Dimmer
8 76 Synchronizing strobe;

Strobe from slow to fast

77 145 Pulse strobe ;

Strobe from slow to fast

146 215 Random strobe ;

strobe from slow to fast

216 255 Dimmer

Product Dimension Drawing

As below :AVTechsmart-miniRETROB100L-Light-03

Technical Parameter Diagram

Item Technical Parameter
Work voltage 110 ~ 230V50/60HZ
Power consumption 210W
Light source 7×30W LED
DMX channel 1CH/6CH /7CH/9CH
Control Mode Auto-run , Sound control ,DMX control
Color temperature 2200K
Dimension 456 x 520 x130mm
Wight 8.3KG
Packing Carton/1pcs , Flight case/4pcs

Documents / Resources

AVTechsmart miniRETROB100L Light [pdf] User Manual
MINIRETROB100L, miniRETROB100L Light

References

Leave a comment

Your email address will not be published. Required fields are marked *