Flash Test Set
“
Product Specifications:
- Brand: Aviloo
- Model: Flash Test Set
- Type: Mobile device
- Display: LED
- Distance Requirement: Maintain a distance of 20 cm during
operation
Product Usage Instructions:
Flash Test Set Up:
- Ensure the vehicle is not charging.
- Set up the Aviloo box by placing it near the vehicle.
Performing the Flash Test:
Follow these steps to perform the flash test:
- Observe the LED display on the Aviloo box:
- Flashing blue: Indicates the box is booting up.
- Yellow light: Test in progress.
- Flashing green: Data transfer.
- Green light: Test completed.
- If the red light comes on, the FLASH test has failed. Refer to
the notes at the bottom right for guidance.
End of the Flash Test:
After the test is completed, take the following actions:
- Check at https://aviloo.link/database to verify if the vehicle
can be tested. - If needed, repeat the FLASH Test according to the provided
instructions. - If you encounter any issues, contact AVILOO Customer Management
for assistance.
Note:
Changes or modifications not approved by Aviloo could void the
user’s authority to operate the equipment.
AVILOO BOX LED-DISPLAY:
Make note of the different LED indicators on the Aviloo box and
their corresponding meanings.
FAQ:
- Q: What should I do if the FLASH test fails?
- A: If the red light comes on during the test, it indicates a
failed FLASH test. Refer to the notes at the bottom right for
further instructions. You may need to repeat the test or contact
AVILOO Customer Management for assistance. - Q: How do I know if the Aviloo box is booting up?
- A: The flashing blue light on the Aviloo box indicates that it
is booting up. - Q: What does a green light on the Aviloo box signify?
- A: A green light indicates that the test has been successfully
completed.
“`
Short instructions for the AVILOO FLASH Test test the drive battery in 3 simple steps
CAUTION: Make sure the vehicle is not
charging.
1
FLASH TEST SET UP
2
PERFORM THE FLASH TEST
3
END OF THE FLASH TEST
· Open the driver’s door (leave it open during the test).
· VW, Skoda, Cupra and Seat Models: unlock the hood before plugging in the AVILOO Box (it is not necessary to open it).
· Plug the AVILOO Box into the OBD-2-port.
· Start the vehicle and leave the vehicle in park mode so that the systems necessary for the test remain active.
· Turn off the heating and air conditioning.
· TIP: The AVILOO WebAPP helps you locate the OBD-2-port in the vehicle.
· Wait for the yellow flashing one LED indicating that the AVILOO Box is ready for the FLASH Test.
· Fasten the driver’s seatbelt to keep the systems necessary for the test active.
· Note for all Tesla Models: switch the vehicle to drive mode and keep your foot on the brake to prevent the vehicle from moving (due to the lack of an “ignition”).
· Wait for the solid green LED, which indicates that the FLASH Test is complete.
· Turn off the vehicle.
· Unbuckle the seat belt.
· Unplug the AVILOO Box.
· Close the driver’s door and, if necessary, the hood.
· The AVILOO BATTERY CERTIFICATE is sent via email to the address registered to the respective AVILOO Box.
Please note: Changes or modifications not expressly approved by Aviloo could void the user’s authority to operate the equipment. This is a mobile device and the user must ensure that they maintain a distance of 20 cm during operation.
AVILOO BOX LED-DISPLAY
Flashing blue: indicates that the box is booting up.
DISPLAY IN THE AVILOO WEBAPP
Yellow light: Test in progress.
If red lights up: FLASH Test failed (see notes at bottom right).
Flashing green: Data transfer.
Green light: Test completed.
IMPORTANT NOTES · To keep the software up to date,
leave the box plugged into the power supply when not in use. · Red LED means: FLASH Test failed.
Take the following measures:
1. Check at https://aviloo.link/database whether the vehicle can be tested.
2. Repeat the FLASH Test according to the instructions.
3. Contact AVILOO Customer Management.
VERSION 06/25
Documents / Resources
 |
AVILOO Flash Test Set [pdf] Instruction Manual Flash Test Set, Test Set |