AVerMedia LogoC285 Game Capture HD II Video Streaming and Capture Device
User Manual

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device

C285 Game Capture HD II Video Streaming and Capture Device

European Community Compliance Statement
Class B
CE SYMBOL This product is herewith confirmed to comply with the requirements set out in the Council Directives on the approximation of the laws of the Member States relating to Electromagnetic Compatibility Directive (EMC) 2004 /108 / EC, Low Voltage Directive (LVD) 2006/95/EC and Energy-related Products Directive (ErP) 2009/125/EC.

Responsible manufacturer:
AVerMedia Technologies, Inc.
No. 135, Jian 1st Rd.,Zhonghe Dist., New Taipei City 23585, Taiwan
TEL: +886-2-2226-3630
European Community contact:
AVerMedia Technologies Europe B.V.
Kwartsweg 50, 2665 NN, Bleiswijk, The Netherlands
Technical Support: http://www.avermedia.com/avertv/Support/
FCC Compliance Statement (United States) 

VIKING X 1000 Solar Charging Station - icon 8 FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Federal Communications Commission Statement
NOTE- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/television technician for help.

CAUTION ON MODIFICATIONS
To comply with the limits for the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must be installed in computer equipment certified to comply with the Class B limits. All cables used to connect the computer and peripherals must be shielded and grounded. Operation with non-certified computers or non-shielded cables may result in interference to radio or television reception.
Changes and modifications not expressly approved by the manufacturer or registrant of the equipment can void your authority to operate the equipment under Federal Communications Commission rules.

Responsible manufacturer:
AVerMedia Technologies, Inc.
No. 135, Jian 1st Rd.,Zhonghe Dist., New Taipei City 23585, Taiwan
TEL: +886-2-2226-3630

USA Office contact:
AVerMedia Technologies U.S.A.
47358 Fremont Blvd., Fremont, CA 94538
Technical Support: http://www.avermedia.com/avertv/Support/

WEE-Disposal-icon.png WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
The mark of Crossed-out wheeled bin indicates that this product must not be disposed of with your other household waste. Instead, you need to dispose of the waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. For more information about where to drop off your waste equipment for recycling, please contact your household waste disposal service or the shop where you purchased the product.

psb SPEAKERS ALPHA AM3 Compact Powered Speakers - ICON Battery Safety Information

  • Use of carbon-zinc battery for remote control is strongly recommended.
  • Use of other types of batteries, such as alkaline or rechargeable (nickel-cadmium), may cause battery current overload or battery leakage and corrosion which can damage the remote control.
  • Store the batteries in a cool dry place.
  • Do not dispose of used batteries in domestic waste. Dispose of batteries at special collection points or return to point of sale if applies.
  • Remove the batteries during long periods of non-use. Always remove exhausted batteries from the remote control. Battery leakage and corrosion can damage this remote control, dispose of batteries safely.
  • Do not mix old and new batteries.
  • Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
  • Do not dispose of batteries in a fire. The batteries may explode or leak.
  • Never short circuit the battery terminals.

ICES-003 (Canada)
CES-003 Issue 5 Class B: C285
GOST-R Certification (Russia)
AVerMedia Icon 1 № РОСС TW. AГ98.B06472
Срок действия с
AГ98 14.02.2013 г по 13.02.2015 г
Disclaimer & Copyright
© 2013 by AVerMedia Technologies, Inc. All rights reserved. No part of this document may be reproduced or transmitted in any form, or by any means (Electronic, mechanical, photocopy, recording, or otherwise) without prior written permission of AVerMedia Technologies, Inc. Information in this document is subject to change without notice. AVerMedia Technologies, Inc. reserves the right to modify, change, improve or enhance its products and to make changes in the content without obligation to notify any person or organization of such changes. Please visit avermedia.com to get the updates of the operation and use of AVerMedia products.
“AVerMedia” is trademark and logo of AVerMedia Technologies, Inc. Apple, the Apple logo, iPod, iPhone, iPad and Apple TV are
trademarks and/or registered trademark of Apple Inc., registered in the U.S. and other countries. Other trademarks used herein for description purpose only belong to each of their companies. Picture shown may vary from actual product.
This product uses Arphic Font.
This software uses libraries from the Libav project under the LGPLv2.1.
AVerMedia Logo 1
International Headquarter Office
Address No.135, Jian 1st Rd., Zhonghe Dist., New Taipei City 23585, Taiwan (R.O.C.)
Website www.avermedia.com/
Tel +886-2-2226-3630

Specifications

Product Name Capture Box
Model No. C285
Power
Input Rating 12V 1.5A
Power Consumption < 7W (power consumption of hard drive not included)
Standby Power Consumption < 0.5W (Without Pass Through)
Adapter Rating Input: 100-240V~, 50-60Hz 0.5A Max. Output: 12V 1.5A
Dimension
Size 190 mm(W) x33.5 mm (H)x 152.5 mm (D)
Weight 421 g
Environmental Condition
Operating Temperature 0~40℃

System Requirements

  •  TV/monitor with component video (YPrPb) input
  •  TV/monitor with 720p or 1080p resolution (recommended)
  • Game console/video device with component video (YPrPb) output
  • NTFS-formatted hard drive with capacity greater than 500 GB is recommended
    (The supported maximum storage capacity of the hard drive is 2TB.)
  • Hard drive is highly preferred over flash drive to minimize the risk of recording failure

Thank you for purchasing the Capture Box. Please read this user manual carefully to ensure proper use of this product. We recommend you to keep it for future reference.

Introduction 

The Capture Box, a stand-alone video capture box specially designed for TV gamers, allows you to capture HD content up to 1080p from various video game consoles, such as PlayStation® 3, Xbox 360 and Wii U. The Capture Box records HD gameplays directly to your hard disk drive (HDD) for later viewing and further editing, eschewing the hassle of setting up a PC nearby your TV set. Most attractively, the one-press capture button allows you to instantly grab high score screen and record your exciting gameplay footage with nearly no effort. The Capture Box can record from either HDMI (without HDCP protection) or Component Video at up to 1080p. Other than that, the Capture Box can pair up with the dedicated app GameMate, which turns your smartphone into a second screen remote controller. You can view capture and uploading status on the screen of your smartphone.

Chapter 1 Package Contents

Please confirm that the package contains the following items. If any of the package contents are missing or damaged, please contact the distributor immediately.

Game Capture HD II

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture

Power Adapter

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device 1

Power Adapter Outlet Module

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 1

HDMI Cable

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 2

User Manual

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 3

Quick Guide

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 4

Remote Control (Batteries Included)

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 5

  • The accessories that come with the package may slightly vary depending on different sales regions.
  • The Capture Box is made for record and capture media materials that are legally owned or licensed by the
    user only. Any violation of copyrights or other intellectual property rights is not allowed.
  • AVerMedia regularly releases the latest version of firmware for the Capture Box. Having the latest firmware enhances the functionality of the Capture Box. To download the latest firmware file, please go to /www.avermedia.com and then enter the model name in Product Search field. Firmware file is available on the product information page (See Chapter 6 for details).
  • If problems are encountered, refer to FAQ section at www.avermedia.com for further troubleshooting.

1.1 Other Items You Need
In order to fully enjoy the recording, the capturing functions of the Capture Box and the dedicated iPhone application, you will need to have the following items prepared:

Item   You need the item to… 
Storage Device AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 6 Save recordings and snapshots.
Play Station 3 AV
Component Cable
AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 7 Connect with PS3 console.
Router (DHCP IP Network
Recommended)
AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 8 Pair up with GameMate.
iPhone 4/ 5, 4s AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 9 Use GameMate.
Headset / Microphone AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 10 Record live commentary.
RJ45 Cable AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 11 To upload captured content
  • Other than iPhone, 4, iPhone 4s, iPhone 5, GameMate also supports iPad and iPod touch.
  • For further smartphone support, refer to www.avermedia.com for latest update.

Chapter 2 The Unit Parts

2.1 Front Panel
The button panel found on the front of the unit provides quick access to commonly used functions.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Game Capture 12

  #  Buttons  Descriptions 
1 AVerMedia Icon 2 Record
Press to start / stop recording.
Hold down the button for 4 seconds to force shut down the Capture Box
2 AVerMedia Icon 3 Power
Press to turn the unit on

2.2 Infrared Sensor 

When using the remote control, aim it at the infrared (IR) sensor located at the front panel of the unit. The remote control must be held at an angle within 30 degrees perpendicular to the IR sensor to function correctly. The distance between the remote control and the sensor should not exceed 6 meters (20 feet).

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor

2.3 LED Indicator
The LED indicators on the front of the unit show the device’s status.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor 1

  1. HDMI source LED indicator
  2. YPbPr source LED indicator
  3. Record status LED indicator
  4. Power status LED indicator
Condition  Source Record  Power 
Powered on Glows solid green
Ready to record/snapshot Solid green Solid green
Recording Solid green Breathing Solid green
Take a snapshot Flashes red once Flashes red once Flashes red once
Unable to record/snapshot Solid green Flashes green continuously
No source Flashes green continuously
Source is available Glows solid green
Power off in progress Solid green  Flashes green continuously
Pass through ON When powering off Solid orange
Pause recording Solid red Solid red Solid red
Record finish in progress Solid green Flashes red continuously Solid green
Storage space is low Solid green Glows at a slowly pace Solid green
Device is not ready Flashes green continuously
Problems like no storage/no signal/protected content Flashes green continuously
Accepting a remote control command Flashes green once

Press [F1] to obtain LED light indicator status.

2.4 Connection Ports
2.4.1 Front View

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor 2

 

  1. USB slot
  2. MIC input
  3. Headphone output

•  USB slot is for external HDD storage device connection as well as for firmware upgrade via storage device.
•  USB hub is not supported.
•  There will be no function or reply when connecting the Capture Box to the computer via USB.

2.4.2 Rear View 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor 3

  1. Component video input
  2. Audio L/R input
  3. HDMI input
  4. HDMI output
  5. LAN port
  6. DC-IN

Chapter 3 The Remote Control

The descriptions below show the deployment of the keys on the remote control.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Remote Control

Buttons Descriptions 
1 AVerMedia Icon 4 Press to turn the unit on / into stand-by mode.
2 AVerMedia Icon 5 Press to access the main menu. Press again to exit.
3 AVerMedia Icon 6 Press the navigation keys to move among options.
Press OK to confirm a selection.
Press OK to mark/ unmark segment in post- editing.
4 AVerMedia Icon 7 Press to play the latest recorded file or view the last captured image.
5 AVerMedia Icon 8 Press to start / stop recording.
6 AVerMedia Icon 9 Press to start playing the selected file.
Press to play the file at normal (1x) speed when slow motion, rewind, or fast-forward is active.
7 AVerMedia Icon 10 Press to stop the playback.
Press to stop the recording.
8 AVerMedia Icon 11 Press to rewind (2x, 4x, 8x, 16x, 32x).
9 Press to return to the previous page.
10 AVerMedia Icon 12 Press to display the video/snapshot quality adjustment screen. Press again to exit.
11 AVerMedia Icon 13 Press to safely remove external hard disk in Menu
(Follow the on-screen instruction)
12 AVerMedia Icon 14 (Follow the on-screen instruction)
13 AVerMedia Icon 15 (Follow the on-screen instruction)
14 AVerMedia Icon 16 Press to switch between Component and HDMI sources.
15 AVerMedia- icon1 Press to display the on-screen information, including mode, source and audio sources.
16 AVerMedia Icon 17 Press to exit the current page and return to the previous page.
17 AVerMedia Icon 18 Press to take a snapshot during gameplay or video playback.
18 AVerMedia Icon 19 Press to pause the playback. Press OK or AVerMedia Icon 9  to resume playback.    Press to pause the recording.
19 AVerMedia Icon 20 Press to play the video in slow motion (1/2x). Press again to enter frame- by- frame mode (See Chapter 5 for details).
20 AVerMedia Icon 21 Press to fast-forward (2x, 4x, 8x, 16x, 32x).
21 AVerMedia Icon 22 Press to go to the next page.
22 AVerMedia Icon 23 Press to delete the selected files.
23 AVerMedia Icon 24 Press to display the disk information. Press again to hide it.

Chapter 4 Installation & First Time Setup

4.1 Supported Resolutions
The Game Capture HD II supports Component (YPbPr) and HDMI input resolution as follows:

HDMI / Component (YPbPr)
480i/576i
480p/576p
720p (50 & 60Hz)
1080i (50 & 60Hz)
1080p (50 & 60Hz)

The Game Capture HD II records the exact display resolution under most circumstances. Exceptions can only be found when the input resolution is set as 1080p:

Source Resolution  Display Resolution  Recorded Resolution 
1080p (60fps) 1080i (60fps) 1080p (30fps)
1080p (50fps) 1080i (50fps) 1080p (25fps)

Estimated recording duration for different video quality settings:
HD 1080p

Video Quality
Storage Capacity
Optimal (20 Mbps) Good (18 Mbps) Maximum Recording Length (15 Mbps)
1TB 100 hrs 110 hrs 125 hrs
2TB 200 hrs 220hrs 250hrs

HD 720P

Video Quality
Storage Capacity
Optimal (20 Mbps) Good (15 Mbps) Maximum Recording Length (10 Mbps)
1TB 100 hrs 125hrs 200 hrs
2TB 200 hrs 250 hrs 400hrs

HD 1080i

Video Quality
Storage Capacity
Optimal (15 Mbps) Good (12 Mbps) Maximum Recording Length (10 Mbps)
1TB 125 hrs 150 hrs 200 hrs
2TB 250 hrs 300 hrs 400 hrs

SD 480i(576i)/480P(576P)

Video Quality Storage Capacity Optimal (7.5 Mbps) Good (5 Mbps) Maximum Recording Length (3 Mbps)
1TB 250 hrs 400 hrs 650 hrs
2TB 500 hrs 800 hrs 1300 hrs

*Recording with higher video quality takes up more disk space.

4.2 Hardware Installation
AVerMedia- icon2 Please follow the steps below to properly connect the Capture Box and your TV/ video game consoles.

  • If you would like to install internal hard drive, install it before turning on the Capture Box.
  •  Make sure that the cables are firmly connected and that neither of the cables is loose. If any of the cables are loose or disconnected, there may be a loss of signal or screen color problems.

Step 1 Check the Connection of Your Game Consoles and TV
Make sure all cables connecting the Capture Box to your game consoles and TV are well-connected. Doing so will save you a lot of time from locating problems later. First, please check the connection of your game consoles. Second, make sure that the connection to TV is good.
Step 2 Connect the Device to Your Wii U / Xbox 360 Using HDMI Cable

Connect one end of the HDMI cable to the HDMI IN port on the rear of the device and the other end to the HDMI OUT port on your Xbox 360/ Wii U.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - HDMI Cable

Warning icon PLEASE DO NOT USE HDMI SPLITTERS TO BYPASS COPY PROTECTION.

Connect the Device to Your PlayStation 3 / Wii Using Component AV Cable
Plug the green, blue, red connectors into the COMPONENT VIDEO IN port and white and red connectors into the AUDIO IN port on the rear of the device. Then, plug the other end to your game console.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - HDMI Cable 1

  • AVerMedia- icon2 “PlayStation 3 Component AV Cable” and Wii Component Cable is NOT Included. Please purchase separately if needed.

Step 3 Connecting the Device to Your TV Using HDMI Cable

Connect one end of the HDMI cable to the HDMI OUT port on the rear of the device and the other end to the HDMI IN port on your TV.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - HDMI Cable 2

Step 4 Power on Your Game Console
Turn on your game console.
Step 5 Install and Connecting the Power Adapter
Slide the Power Adapter Outlet Module into the groove on the Power Adapter. Connect the Power Adapter connector to the DC-IN port on the rear of the device. Then plug the power adapter to a wall outlet.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - HDMI Cable 3

Step 6 Connecting to the Network
To automatically obtain time and other information, you need to connect the Capture Box to an Ethernet LAN. Make sure the LAN wire is well-connected before you continue to the next step. Meanwhile, a router which supports DHCP IP network is recommended for you to pair up the Game Capture HD II with your iPhone.

  • It is recommended that you connect the Capture Box before running first time setup.

Step 7 Plug in USB Hard Drive/ HDD
Connect your portable USB hard drive or hard disk drive (HDD) to the USB port on the front of the Capture Box. Please make sure you use an NTFS format USB hard drive or hard disk drive (HDD). Under the condition that no hard drive is connected to the device, the power light will continue to flash. Therefore, it is advised that you plug in USB hard drive or hard disk drive (HDD). Please see Chapter 4.3.2 for further details about installing an internal hard drive.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor 4

Step 8 Power on the Capture Box
Press the power button on the front panel of the device.
Or
Use the power button on the remote control.
The POWER LED indicator lights up green, when that the device is power-on.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor 5

  • LiFE Character Hair Dryer with 220Q AC Motor and Ion Function - icon 2 It is important that you power on/ off the Capture Box following suggested procedure . Fail to do so may lead to damage of the Capture Box or data loss

Step 9 Check Video on TV screen
Make sure that there is game console video content displayed on TV screen.

LiFE Character Hair Dryer with 220Q AC Motor and Ion Function - icon 2 If your TV is not displaying video properly, please check the followings:

  • Supported resolutions vary depending on the TV in use. For details, please refer to the documentation that comes with your TV.
  • Power off Capture Box and then make sure that the device is connected properly and with the proper cables.
  • If there is still no video signal on TV, refer to FAQ section at www.avermedia.com for further troubleshooting.

Connecting the Device to Your Microphone and Headset
Plug in the microphone connector into the MIC Input port on the front panel of the device. Same as microphone, plug in the headset connectors into the headphone and microphone ports on the front  panel of the device. This procedure is only needed when you intend to add commentary to your gameplay video. Please refer to Chapter 6 for details.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Headset

  • AVerMedia- icon2 When headphone is connected to the Capture Box, the gameplay will be muted as sound will come out from the headphone.
  • Hereafter a headset refers to the device you use to record while headphone refers to the headphone port on the front panel of the Capture Box.

4.3 Storage Device Installation 

The Capture Box supports 2.5 inch internal hard drive and external USB storage device. You can save the recorded files and snapshots either to the internal HDD or external one.

4.3.1 USB Storage Device Insertion
Connect your portable USB hard drive to the USB port on the front of the Capture Box

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Headset 1

  • LiFE Character Hair Dryer with 220Q AC Motor and Ion Function - icon 2  It is highly recommended to use a NTFS format hard drive instead of a flash drive to minimize the risk of recording failure.
  • To avoid any possible data loss, go to main menu and press [F1] of your remote control to safely remove the external storage disk before unplugging it from the Capture Box.

4.3.2 HDD Installation and Removal 

  • AVerMedia- icon2 It is highly recommended to use a new unformatted hard drive or a hard drive formatted as NTFS file system. The maximum supported storage capacity of the hard drive is 2TB.
  • Before installing or removing the internal HDD, please disconnect the power supply from the Capture Box to avoid data loss.
  • Removing internal HDD immediately after powering-off may cause personal injury due to heat. Please wait until the HDD cools down completely (it takes approximately 10 minutes) before any attempt to remove it.

To install the internal HDD:
Step 1
Remove the HDD Lid
Open the HDD lid on the bottom of the Capture Box.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Headset 2

Step 2
Before Installing Internal HDD
Use the measuring card to measure the height of your HDD (7mm or 9.5mm).

  • LiFE Character Hair Dryer with 220Q AC Motor and Ion Function - icon 2 Please refer to the Appendix C for the measuring card.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Headset 3

Adjust the rotary knob attached to the inner side of the lid to fit the height of your HDD.
The default position of the rotary knob fits HDD with 9.5mm height. If you use HDD with 7mm/9.5mm height, rotate the rotary knob to the other direction.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor 6

Step 3 Inserting the HDD
Place the HDD on the slot with the sticker-side facing up and the HDD connector end facing to the left.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor7

Align and insert the HDD connectors all the way into the SATA connector. Push in firmly to secure them.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor8

Step 4
Replace the HDD Lid
Place the HDD lid back and snap it into place.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Sensor 7

To remove the internal HDD:
Step 1 Remove the HDD Lid
AVerMedia- icon2 Please wait until the HDD cools down completely (it takes approximately 10 minutes) before any attempt to remove it.
Use your fingertip to flip open the HDD lid, located on the bottom of the Capture Box.
Lift off the lid and set it aside.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Headset5

Step 2 Removing the HDD
Pull the HDD out in the direction of the arrow. Then lift the HDD out of the slot.

AVerMedia- icon3

Step 3 Replacing the HDD Lid
Place the HDD lid back and snap it into place.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Headset4

  • LiFE Character Hair Dryer with 220Q AC Motor and Ion Function - icon 2 It is typical that after a hard drive is formatted, the actual disk space of the drive would be slightly less than its unformatted capacity.

4.4 Setup Wizard
When the first time you power on the Capture Box unit, the setup wizard appears. The following steps guide you through the initial configuration process.

  • AVerMedia- icon2 Make sure to install a hard drive (internal or external) and to connect to the internet beforehand.
  • For the first-time initialization, a short duration of black screen (approximately 20 seconds) is followed by AVerMedia logo. The blinking green status light indicates that the Game Capture HD II is starting up. Please wait until the welcome screen appears.

Step 1 Setting up Language
When the welcome page appears, use ▲/▼ to select your preferred language. Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - Headset7

Step 2 A/V Pass Thru.
It is suggested that A/V Pass Through to be turned ON.

AVerMedia- icon4

Step 3 (1) Reminder
Make sure a NTFS-formatted hard drive is connected or installed to the device. (For details, see Chapter 4.2)
Check the connection of network.
Press OK to start setup.
A router which supports DHCP IP network is recommended. Also, refer to Ch. 6.2 for Manual connection setup.

AVerMedia- icon5

Step 3 (2) Network Connection Failure
If you have not connected to a valid network, a short result of failed network connection will be shown.
Press OK to continue.
Press AVerMedia- icon6 to go back to the previous page.

AVerMedia- icon7

Step 4 (1) No Hard Drive Detected
If you have not yet installed any storage device, install it before continuing the setup process.
Then press AVerMedia- icon6 to go to the previous screen and press OK to run disk checking process.
AVerMedia- icon8Step 4 (2) Finishing Setup Wizard
Once a NTFS-formatted hard drive is connected, a Settings Complete notice will be shown.
You can start to record and take snapshot right away. Press OK to exit the wizard and start using Capture Box. The game screen then appears.

AVerMedia- icon9

  • AVerMedia- icon2 Unplug the Capture Box from the power supply before installing an internal HDD.
  • Sometimes the connection test in Wizard will appear to be failed even though you have connected the RJ45 cable to the Capture Box. Go to Menu> Network> Network Settings> Manually Setup to set the network manually.

4.5 Video Output Settings for Game Consoles
The Capture Box supports YPbPr / HDMI input resolution up to 1080p.
4.5.1 Video Output Settings for PlayStation 3

Step 1
Power on your PlayStation 3 console.
On your console, go to Settings > Display
Settings > Video Output Settings.

AVerMedia- icon10

Step 2
Select Component/D-terminal and confirm the selection. Then your TV screen goes blank immediately.
Now use your TV remote to switch the TV input source to Component (YPbPr). The screen then comes back on again.

AVerMedia- icon11

Step 3
Check ALL the resolutions. Confirm the setting.

AVerMedia- icon12

Step 4
Select Set Audio Output Settings.
Select Audio Input Connector/SCART/ AV MULTI as audio output. Confirm the setting.

4.5.2 Video Output Settings for Xbox 360

  • AVerMedia- icon2 Before resetting video output for XBox 360, make sure to properly connect the Capture Box with your Xbox 360.
  •  Make sure to power off both the Capture Box and your Xbox beforehand.
  • Supported resolutions vary depending on the TV in use. For details, please refer to the documentation that comes with your TV.

Power on your Xbox console.
On your console, go to My Xbox on the dashboard and scroll all the way to the right to System Settings.
Then select Console Settings > Display > HDTV Settings.

AVerMedia- icon13

  • AVerMedia- icon2 Please set the audio output of all game consoles as auto.
  • Although the Capture Box do not support DOLBY 5.1 and 24p resolution video/ audio format, you can still pass through these format while the Capture Box is off.

Chapter 5 Basic Operation

This chapter guides you to record gameplay, capture images, add voice commentary to videos, and instantly play files.

  • AVerMedia- icon2 All the recorded files or snapshots will be saved to the default hard drive destination automatically. Please see Chapter 6 for details.

5.1 Record and Capture
The Capture Box lets you record, capture and adds voice commentary to the videos. Instructions are given as follows.
LiFE Character Hair Dryer with 220Q AC Motor and Ion Function - icon 2 The Capture Box displays gameplay in real-time and standard mode. You can change the default real-time mode to standard mode. Go to Menu> Settings> Display Mode. (Refer to Chapter 6.2 for details.)

OSD Menu Descriptions 
AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig1 Instant Recording During Gameplay
Press AVerMedia Icon 8 to activate instant recording.
Press AVerMedia Icon 8 again or AVerMedia Icon 10 to stop recording.
AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig78 Pause and resume recording
You can skip unwanted footages and resume recording. Only the footages you recorded will be saved and those skipped clips will be
deleted automatically.
Press AVerMedia Icon 19 to pause recording.
Press AVerMedia Icon 19 or AVerMedia Icon 8 to continue recording.

Quick Snapshot During Gameplay
PressAVerMedia Icon 18  to capture current image.
Long Press AVerMedia Icon 18 to activate continuous capture mode. The Capture Box will take 5 snapshots at one time.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig2

Instant Playback
Press to play the latest recorded file or view the last captured image.
PressAVerMedia Icon 10  to stop the playback.
Press ►to skip forward 30 seconds.
Press ◄ to skip backward 10 seconds.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig3

Image Capture During Video Playback
Way 1:
Press AVerMedia Icon 18 to capture current image.
Way 2:
Step 1:
Press AVerMedia Icon 20 to play the video in slow motion (1/2x). Press AVerMedia Icon 20 again to view the video frame by frame.
or
Press AVerMedia Icon 19 to pause the playback. Press  AVerMedia - icon23 to go to previous frame; press AVerMedia Icon 22 to go to next frame.
Step 2:
Press AVerMedia Icon 18 to capture your desired image.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig4

Disk Information
PressAVerMedia - icon21then press OK to display the disk  information. Press again to hide it.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig5

5.2 Adding Commentary
This section shows you how voice commentary is added to your video recording.
Requirements for headset/microphone:
Headset
Connector: 3.5mm jack
Microphone
Frequency Response : 20-16 kHz
Impedance: 2.0 KΩ
Working Voltage: 3V
Connector: 3.5mm jack

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig6

Descriptions
Microphone On
An OSD will be shown if you connected microphone/ to the Capture Box. Your commentary will only be recorded when you press AVerMedia Icon 8 .
Press AVerMedia Icon 8 to record your gameplay with commentary.
Press AVerMedia Icon 8 or AVerMedia Icon 10 to stop recording.

  • AVerMedia- icon2 If headset or microphone is plugged in during the Wizard Setup, the sound can only be heard from your headphone and instructions on voice commentary will not be displayed. Therefore, plug in headset or microphone after you complete Wizard setup so as to follow the headphone/ microphone instructions.
  • All commentary added will be mixed with the gameplay sound. Also, as long as the headphone is connected to the device, all your commentary and background sound will be recorded. Therefore, remember to stop recording and remove the headphone when no commentary is needed.
  • If the microphone is disconnected/ connected to the Capture Box during recording, the sound will also be recorded. To make sure the Please avoid plugging off the microphone during recording process.
  • The volume you hear in the commentary test may be slightly different from the actual recording. It is recommended that you run an mock test beforehand to be familiar with the recorded volume.
  • It is normal to hear your own voice when recording with HDMI input source.
  • No OSD will be shown when you connect only the headphone to the Capture Box.

Chapter 6 OSD Menu

Under the menu, you can check and manage both your recorded files and snapshots, and customize your preferences.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig7

  1. Remaining Time for Recording
  2. Connecting to GameMate
  3.  Network Connection
  4.  Current Time

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig8

Descriptions
Basic Operation 

Press AVerMedia - icon22 to bring up the menu.
Press AVerMedia - icon22 or AVerMedia- icon6 to return to the game screen.
Use ▲/▼ to make selection on the menu and OK to enter a submenu.
In the submenu, use ▲/▼ to make selection and OK to confirm. Press AVerMedia- icon6 to return to the previous page.
Press F1 to safely remove the storage device..
The upper left corner shows your current default storage device and available remaining recording

6.1 Media Studio
You can check both recordings and snapshots captured by the Capture Box in “Media Studio”.
Capture Format:

Video MP4 (Codec: H.264 format with AAC audio)
Image JPEG
  • AVerMedia- icon2 It is recommended that you view only videos and snapshots that are recorded by the Capture Box. Attempt to open files taken by other equipment (such as a camera) on the Capture Box is very likely to fail.

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig9

Descriptions
Navigating 

Use the navigation keys ◄/►/▲/▼ to select among items.
Press F1 to sort the files by file name, file size, or file format.
Press F2 to switch between list mode and thumbnail mode.
Press F3 to rename, edit, share the highlighted file
Press AVerMedia Icon 22 to go to the next page.
Press AVerMedia - icon23 return to the previous page.
Press AVerMedia - icon22 to directly access the main menu.

Video Playback
Press AVerMedia Icon 9 or OK to start playing the selected video.
Press AVerMedia Icon 19 or OK to pause the playback. Press AVerMedia Icon 9 or OK to resume playback.
Press  AVerMedia Icon 20 to play the video in slow motion (1/2x).
Press AVerMedia Icon 11 to rewind at 2x, 4x, 8x, 16x, 32x speed.
Press AVerMedia Icon 21 to fast forward at 2x, 4x, 8x, 16x, 32x speed.
Press AVerMedia Icon 9 to play the file at normal (1x) speed when slow motion, rewind, or fast-forward is active.
Press AVerMedia Icon 10 to stop the playback.
Press AVerMedia - icon24 to display the playback information, including storage disk, recording resolution, duration, elapsed and remaining time, and file name.
* Only video files captured by the Capture Box are supported.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig10

Snapshots Viewing
Press AVerMedia Icon 9 or OK to view the selected image.
Press AVerMedia Icon 10 or AVerMedia- icon6 to return.
* Only image files captured by the Capture Box are supported.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig11

6.1.1 Post- Edit Capture Box Recorded Videos
This section shows you how to cut, recombine and share videos on YouTube recorded by the Capture Box.

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig12

Descriptions
Select a Video
Select the file you would like to edit by using the navigation keys ◄/►/▲/▼.
Edit/ Share
Press F3 to edit or share the selected video.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig13

Change File Name
Input your file name by using the navigation keys ▲/▼ to select characters, numerals or symbols. Use the navigation keys ◄/► to go to the next/ last character.
Press F1 to switch between characters, numerals and symbols.
Press AVerMedia- icon6 to go back to cancel the change you made.
Press OK to save the edited file name.
Press AVerMedia - icon29 to clear all.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig14

How to Edit
An instruction on how to edit a video will be displayed, press OK to start editing.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig15

Edit Mode
You can cut and recombine your selected video in Edit Mode.
To cut the video, you will need to create one or more segments within the video.
Step 1:
To locate a scene, use direction keys or AVerMedia Icon 9 to search the scene.
You can also use navigation keys ▲/▼ to search scene by specific hour, minute, and second on the left hand side of the screen.
Press OK to mark or unmark the scene.
Step 2:
Repeat Step 1 so as to create a segment.
Press OK to keep or delete the segment.
Press F1 to switch between Search Scene and Segment search.
Press F2 to clear all marks you made on the video.
Press F3 to export the video.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig16

Preview
The Capture Box automatically recombines the segments you choose to keep during editing.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig17

Export
The estimated time varies by different storage disks. Refer export time to the actual use of your storage disk.
Press OK to export the video.
PressAVerMedia- icon6 to continue editing.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig18

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig19

Descriptions
Exporting…

The bar in the middle shows the progress of video exporting and estimated time.
Click on to cancel exporting.
Click on to hide the exporting information.

Exit
Press OK to exit from the editing mode.
Press AVerMedia- icon6 to exit
Press F1 to continue editing.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig20

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig21

Descriptions
Share Videos on YouTube
Use ▲/▼ to select the task you would like to undergo. Select ‘Share on YouTube’ to share your videos.

Share On YouTube
Before you share your recorded videos on YouTube, make sure you:

  1. Built a YouTube account and also a personal channel.
  2. Have your PC/ NB next to you if you activate two- step verification of your YouTube account.

To ensure the stability of uploading, upload videos that are within one hour.
Make sure the YouTube account is verified to upload videos that are longer than 15 minutes.
Press AVerMedia- icon6 to continue editing.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig22Press OK to continue uploading.
Press F1 to skip this reminder afterwards.
Account Setup
Use ▲/▼ to select the task you would like to undergo.
Press AVerMedia- icon6 to go back to last level.
Press OK to edit your email or password.
Press F1 to save the change you made.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig23

Edit Before Uploading
Press return to the last page.
Press OK to start uploading.
Press F1 to set the privacy.
Press F2 to change account.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig24

Uploading Complete
You have successfully upload the video.
You can edit your video title on YouTube.
Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig25

  • AVerMedia- icon2 The recommended length of each video should be less than 1 hour.
  • The Capture Box is made for record and capture media materials that are legally owned or licensed by the user only. Uploading videos that are protected by copyright and other laws is not allowed. YouTube may shut down the account for copyright protection reason.
  • YouTube account verification is required when you upload video that are longer than 15 minutes. Refer to YouTube website for further details.
  • Occasionally, it takes two to three days for your videos to be shown on YouTube. Please wait for a few days if you did not see the uploaded videos online.

6.2 File Management 

“File Management” lets you manage videos and snapshots captured by the Capture Box. You can copy files between internal hard drive and external USB storage device, and delete unwanted files. Before entering this submenu, insert your storage device first (USB 2.0/ 3.0 storage device / 2.5” HDD in NTFS format).

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig26

Descriptions
Select Partition
Use the navigation keys ◄/►/▲/▼ to select the partition.
Press AVerMedia Icon 9 to playback the video.
Press F1 to change the file sorting rule.

File Management User Interface: 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig27

  1. A list displaying files located on the internal hard disk
  2. A set of editing tools
  3. A list displaying files located on the USB disk
  4. Information display area

Descriptions on Editing Tools:

Buttons Descriptions 
1 AVerMedia - icon25 Copy files to USB disk
2 AVerMedia - icon26 Copy files to internal hard disk
3 AVerMedia - icon27 Select all
4 AVerMedia - icon28 Deselect all
5 AVerMedia - icon29 Delete

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig28

Descriptions 

Copying Files from Internal HDD to USB Disk
Step 1:
On the left-side list, use ▲/▼ to highlight the file that you want to copy to USB disk. Press OK to select / unselect an item.
SelectAVerMedia - icon27 and press OK to select all files.
Select AVerMedia - icon28 and press OK to deselect all files.
Step 2:
Select AVerMedia - icon25 and press OK to copy selected file(s) to USB disk.
Press AVerMedia- icon6 to cancel copying the files in a progress.
Step 3:
Press OK.
Copying Files from USB Disk to Internal HDD works in the opposite way as above mentioned.
*If the file is comparably large, press F1 to hide the copying or deleting status.

Deleting Files
Step 1:
Use ▲/▼ to highlight the file(s) that you want to delete. Press OK to select/unselect an item.
Select AVerMedia - icon27 and press OK to select all files.
Select AVerMedia - icon28 and press OK to deselect all files.
Step 2:
Select AVerMedia - icon29 and press OK to remove the file from the list.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig29

or
Press AVerMedia - icon29 on the remote and then press OK to remove the file from the list.
Press AVerMedia- icon6 to cancel deleting the files in a progress.
Step 3:
Press OK.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig30

USB Storage Device Removal
In order to avoid data loss, it is highly recommended to safely remove your external  storage device. Please follow the steps below:
Step 1:
Press AVerMedia Icon 24 on the remote control.
Step 2:
Press F2 to remove it.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig31

6.3 Settings
You can customize your preferences in “Settings”.

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig32

Descriptions
Basic Operation
 Use ▲/▼ to select a preferred category. Press OK to make a selection.
Press AVerMedia- icon6 to return to the previous page.
Press AVerMedia - icon22 to directly access the main menu.
Press F1 to safely remove the storage device.

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig33

Descriptions
Language
Use ▲/▼ to select your preferred language.
Press OK to confirm.

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig34

Descriptions
Display Mode
The default mode is set as real-time mode.
Use ▲/▼ to switch between real-time and standard mode.

Real-Time Mode
Real-time mode lets you play games with zero delay. And it is best for FTG, STG, RAC, and  other rhythm games. No recording or snapshot status will be shown on screen. All capture work will run in the background.
However, if any problem occurs during the capturing process, OSD will automatically jumps out.
Press AVerMedia - icon22 to check OSD and track capture status.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig35

Standard Mode
In standard mode, on-going recordings will be shown in the upper right corner of the screen. As there will be slight delay in game, standard mode is recommended for ACT, RPG, and SLG games.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig36

  • AVerMedia- icon2 Black screen may occur when calling for Menu in real-time mode. And the pause varies by TV type.

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig37

Descriptions
Network Settings
Use ▲/▼ to move among options. Press OK to confirm. Before setup, please make sure the Ethernet cable is well connected.
Auto Setup (Recommended):
It is recommended to use Auto Setup to automatically obtain IP and DNS addresses.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig38

Manual Setup :
Use Manual Setup to manually configure IP and DNS addresses.
STEP 1:
Use ▲/▼ to select an item for configuration.
Press OK to confirm.
STEP 2:
Use ◄/► to move among options and ▲/▼ to select a number. Press OK to confirm.
Press OK to save the setting.
Press AVerMedia- icon6 to cancel and return to the previous page.
STEP 3:
Press F1 to save the settings and test the network connectivity.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig39

PPPOE :
Use username and password provided by ISP for connection.
STEP 1:
Use ▲/▼ to select an item for configuration.
Press OK to confirm.
STEP 2:
Use ◄/► to move among options and ▲/▼ to select a character.
Press F1 to switch among capital letters, lower cases, numbers, or signs.
Press OK to save the setting.
Press AVerMedia- icon6 to cancel and return to the previous page.
Press AVerMedia - icon29 to delete selected characters and the character to the right.
STEP 3:
Press F1 to save the settings and test the network connectivity.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig40Network Connectivity Test
Select to test your network connectivity.
Please check the result and fix the problem indicated.
Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig41

Network Connectivity Test
Once network setting is completed, a list of connection details will be displayed.
Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig42

Current Network Information
This page displays the current status of your network connection.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig43

  • AVerMedia- icon2 If network is temporarily inaccessible, manually set up the time zone settings so that the videos and snapshots is named correctly.

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig44

Descriptions
Date and Time
Use ▲/▼ to select an item for configuration.
Press OK to confirm.
Date Format :
Use ▲/▼ to select a preferred date format.
Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig45

Auto Update:
Use ▲/▼ to enable/disable automatic date and time update. Press OK to confirm.
*To use this function, a network connection is required.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig46

Time Zone :
STEP 1:
Use ▲/▼ to move among options and select your area. Press OK to confirm.
STEP 2:
Use ▲/▼ to move among options and select your time zone. Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig47

Time Setup :
Use ◄/► to move among options and ▲/▼ to adjust date and time. Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig48

Daylight Saving Time :
Use ▲/▼ to enable/disable Daylight Saving Time. Press OK to confirm.
*To use this function, a network connection is required.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig49

OSD Menu

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig50

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig51

Descriptions
Disk Management
Storage Destination
Step 1:
Select and press OK to change your current desired default storage device for both recorded files and snapshots.
*AVerMedia - icon30   indicates normal write speed of selected partition; indicates low write speed of selected partition. To make sure recording functions properly, be sure to select partition with normal write speed.
Step 2:
Use ▲/▼ to select the preferred default storage device.
Step 3:
Use ▲/▼ to select a folder and press OK to confirm.
Step 4:
Press F1 to save the setting.
OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig52

Descriptions
Use ▲/▼ to move among options. Press OK to confirm.
Press AVerMedia - icon33 to switch from component and HDMI input sources.
Video Input:
Use ▲/▼ to toggle between various video input source options (Component /HDMI).
Press OK to confirm.
Audio Input:
Use ▲/▼ to toggle between various audio input source options (Stereo Audio/ HDMI).
Press OK to confirm.

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig53

Descriptions
A/V Pass Through:
Use ▲/▼ to enable/disable A/V Pass Through.
Press OK to confirm.
* The default setting is set Off to yield to the power-saving regulation. If this function is enabled, Capture Box still output signal when the Capture Box is off. If this function is disabled, Capture Box does not output signal when the Capture Box is off.
Color Range Setup
Use ▲/▼ to toggle between off, limited, and full. Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig54

OSD Menu 

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig55

Descriptions
Watermark
Add your selected watermark to your videos.
You can customize the display of the watermark by setting up the type, position and also scale.
Press AVerMedia- icon6 to go back to last level.
Press OK to enter the next level.
Press F1 to preview the display.
Watermark Type:
Use to ▲/▼ select from the listed watermark types.
Press OK to save the change.
PressAVerMedia- icon6 to go back to last level.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig56

Position:
Use ▲/▼ to select from the listed watermark positions.
Press OK to save the change.
Press AVerMedia- icon6 to go back to last level.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig57

Display Scale:
Use ▲/▼ to select the display scale.
Press OK to save the change.
Press AVerMedia- icon6 to go back to last level.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig58

OSD Menu

Descriptions
Auto Save

Use ▲/▼ to switch from enable or disable the Auto Save function.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig59

Recording/ Snapshot
Video Quality:
Use ▲/▼ to toggle among various video quality options (Optimal/ Good/ Maximum recording length). Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig60

Snapshot Quality:
Use ▲/▼ to toggle among various snapshot quality options (Best/Better/Good). Press OK to confirm.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig61

Live Commentary
A short demonstration will be played in this section.
Press OK to continue.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig62

Volume:
Use ▲/▼ to move among options and ◄/► to adjust the volume.
Press OK to save the setting.
Press F1 to restore to the default setting.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig63

Sound Mode:
Use ▲/▼ to select a preferred mode for mic recording. Press OK to confirm.
Game player Mode will automatically switch game sound output to your headphone.
To ensure the optimal quality, please use both microphone and headphone for voice commentary recording.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig64Commentator Mode will record both game sound and voice commentary or voice chat from microphone during gameplay.
It is recommended to use an omni-directional or high-sensitive microphone.

OSD Menu

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig65

Descriptions
Firmware Upgrade
Follow the steps below to upgrade the firmware via USB storage device:
Step 1:
To download the latest firmware binary package, please go to www.avermedia.com, and then enter the model name in Product Search field. Firmware file is available on the product information page.
Step 2:
Extract the files by unzipping the package. Copy the firmware files to the root directory of your USB storage device, and then connect it to the Capture Box.
Step 3:
Press F1 to start the firmware upgrade process. Press AVerMedia- icon6 to abort the operation and return to the previous page.
Step 4:
The Capture Box automatically detects whether a different version of firmware is available for upgrade or rollback. Once the firmware upgrade process has completed, press OK to restart the Capture Box.

  • AVerMedia- icon2 The firmware upgrade process takes up approximately 10-14 minutes.
  • Firmware upgrade requires at least 256 MB free space of the storage device (USB/HDD).
  • If problems encountered during firmware upgrade, please clear all the data stored on your USB storage device and repeat the process above.
  • NEVER power off the device or unplug the power supply or remove the USB storage device during the firmware upgrade process. If the firmware upgrade is interrupted for any reason, the device may crash.

Restore to Factory Settings
Press F1 to restore to original factory settings. Press AVerMedia- icon6 to abort the operation and return to the previous page.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig66

Product Information
This page provides information about this product, including product name, model no., and firmware version.
Press F1 to edit the display name.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig67

OSD

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig68

Descriptions
Name your own Capture Box.
Press navigation keys AVerMedia Icon 6 Up and Down to select characters.
Press navigation keys AVerMedia Icon 6 Left and Right to shift to the former or later character.
Press AVerMedia Icon 13 to switch to the next input menu.
Press AVerMedia Icon 23 to delete the character.
Press OK to save the name.
To change product name, go to Menu >Product Name.
* The display name will not only show up when you enable watermark function but also on the pair up list with Game Mate by Aver Media.

Chapter 7 Pairing Capture Box and Game Mate by Aver Media

Game Mate by Aver Media is the dedicated app for smart phones. It allows you to use your smart phone as remote control. You are only a few steps from pairing up the Capture Box with Game Mate.
LiFE Character Hair Dryer with 220Q AC Motor and Ion Function - icon 2 Please download Game Mate by Aver Media from app store first.
To pair up successfully, make sure the Capture Box and Game Mate share the same network. To do so, you will also need a wireless access point for Game Mate. Make sure the LAN is well-connected and you are ready to pair up!

OSD

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig69

Descriptions
It is recommended that the Capture Box and GameMate share a wireless AP. After downloading the GameMate; tap on GameMate on your smartphone. You will see that GameMate is searching available device.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig70

A set of pairing number will be shown on TV screen.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig71 Tap to input the provided four-digit pairing number correctly.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig72

You will see GameMate as shown left hand side when it successfully pairs up with Capture Box.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig73

You can also check the connection of GameMate from the Menu. You will see AVerMedia - icon31 sign on the upper level of the Menu.

  • AVerMedia- icon2 If the connection is lost, please restart the wireless AP or the Capture Box and try again.

Appendix A How to Set Your Game play Snapshot as PS3 Wallpaper

Start to give your PS3 menu screen a fresh and personalized look to show how cool you are! Please follow the steps below to set the image captured by the Capture Box as your PS3 background wallpaper.
Step 1
Remove your USB storage device from the Capture Box, and then plug it into your PS3 console via USB port. Power on your PS3 console.

AVerMedia - icon32

Step 2
On your console, go to Photo > USB Device.
Press the triangle button on your PS3 controller and select “Display All”.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig74

Step 3
Select the image that you wish to use.
Press the Triangle button on your PS3 controller to bring up control panel.
Then scroll to the right and select “Set as Wallpaper”.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig75

Step 4
Use the right joystick to zoom in/out and left joystick to frame the image. When it is the proper size, press ○(Enter). Confirm with ○(Enter) if you are prompted to overwrite your current wallpaper.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig76

Step 5
Done! The snapshot that you have chosen is now set as your PS3 wallpaper.

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device - fig77

LiFE Character Hair Dryer with 220Q AC Motor and Ion Function - icon 2 On your PS3 console, you can go to Settings > Theme Settings > Background to turn wallpaper on or off.

Appendix B Troubleshooting

To download the latest firmware for the Capture Box:

  1. Go to www.avermedia.com.
  2. Enter the model no. (C285) in Product Search field.
  3. The latest firmware file is available on the “AP & Driver” section on the product information page.
Hard Drive Problem  Actions 
Hard drive not detected Make sure that the storage destination is properly set up.
Go to Menu → Settings  → Disk Management → Storage Destination to set storage destination.
Make sure the hard drive is connected/installed and restart the Capture Box.
Make sure the Capture Box has stable power supply while recording or the recording mail fail. Failure of recording may stop the Capture Box from detecting hard disk.
Format current drive to NTFS file system.
It is likely that the hard drive is not set to NTFS format. You can check the hard drive and reformat it by downloading HP USB Disk Storage Format Tool.
Unknown files are found on my hard disk after connecting to the Capture Box The Capture Box will automatically generate files that help boost the operation. Files that have file name extension like
‘.avm_chk_tmp’,
‘.avm_speed_test’, ‘.hd_keepalive’aim
at preserving hard disk speed as well as other crucial record. Please don’t remove them.
Video Display Problems  Actions 
“No input signal” message appears on screen Make sure that all the cables are firmly connected.
Power off the Capture Box and then make sure that the device is connected with the proper cables (See 3.1 Hardware Installation in user manual for details).
Screen color appears abnormal using component input Green screen color with buzzing noise:
Make sure that the red and blue connectors do not come loose.
Mono screen color:
Make sure that the red and blue connectors do not come loose.
Unsuccessful recording of HDMI-input-videos The Capture Box supports all HDMI input except those in HDCP (protected video) form.
Blacken screen using HDMI input If screen is blacken when using HDMI input, please try:
1. Reconnect the HDMI cable from the input source device and also the Capture Box. Also, connect to HDMI port 1 of your TV at all times.
2. Change HDMI cable and try again.
The recording is fast-forwarded or stopped when recording complicated gameplay frames in HD resolution (720p or above)? When recording gameplay in HD resolution (720p or above), fast-forward may be found due to the complicated video content. Follow the tips below to ensure good recording quality:
1. Install a format tool. It is recommended that you format hard disk into NTFS format using HP USB Disk Storage Format Tool. Please find the link:
http://download.cnet.com/HP-USB-Storage-Tool/3000-2094_4-1
Be sure to backup your data before start formatting. All data will be erased once the formatting process begins.
2. Lower gameplay output resolution. Details can be found in C285 user manual. Please refer to PS3/ Xbox 360 video output setting.
3. Lower C285 video quality at Menu> Settings> Edit/ Share
4. Use another high- performance storage disk (For example, another NTFS hard disk).
Playback Problems  Actions
Poor quality of captured video Check video output settings of your game console.
For PS3, set 1080p, 1080i and 720p as video output resolutions. If you only select 1080i, the screen resolution automatically goes to 480i when you play a game that supports 720p. (See 3.5 Video Output Settings for Game Consoles in user manual for details).
Jittery/Jerky video playback on PC Enable the “De-interlace” function of your media player before playback.
Some media players cannot process the interlaced video (1080i / 576i /480i) well. This problem does not persist after video uploaded to YouTube.
Stuttering local video playback Try recording video again using another NTFS-formatted hard drive.
When this problem occurs, it is recommended to play the videos on PC. Alternatively, you can record at a lower bit rate to solve this problem.
This problem does not persist after video uploaded to YouTube.
Microphone volume not loud enough Turn on Microphone volume via Menu.
Turn down game console input volume.
Adjust volume via in-game setting.
Gain Microphone amplifier.
No A/V Pass Through when game console and TV ON Make sure that your TV supports 1080p.
Turn on A/V Pass through via Setting.
File Management Problems  Actions 
Difficulty in locating files All files are named after the date and time they are recorded. In the file management, you can sort files out by its name, the time recorded, and the file size. Make sure the time zone is set correctly or manually setup to obtain correct file name.
For example, a video which recorded at 9:30 a.m., 15 of April, 2013 will be named as:
130415-0930
A recorded videos with commentary will be called:
130415-0930 (Mic)
An edited recorded video will be named as :
130415-0930 (Edit-1)
A videos that has been edited for the second time will be named as :
130415-0930 (Edit-2)
An edited video with commentary will be named as :
130415-0930 (Mic-Edit-1)
Difficulty in locating the folder on your
PC/ laptop
The Game Capture HD II detects all kinds of folder that built in your hard drive; as a result, it is likely that the destination is set to a non-standard folder, for example, a hidden folder.
If you cannot locate the folder that saves the recordings and snapshots, please check if:
1. You have set the destination of recordings and snapshots to a standard folder, making sure that it is not hidden, locked, etc..
2. You load the folder with a Microsoft Windows system. A Linux system does not read non-standard folder like a hidden folder.
Other Problems  Actions 
Firmware upgrade turns out unsuccessful Solutions are as follows:
A. Power off the Capture Box if an internal storage disk is installed. Remove internal storage disk and power on the Capture Box. Connect the USB to your Capture Box to undergo FW upgrade.  (*If you are using a SATA storage disk or the temperature of the hard disk appears high; please wait for 10 minutes for the hard disk to cool down.)
B. Save the unzipped firmware file to the file root of your USB.
C. To enable firmware upgrade, make sure a minimum space of 256 MB on your USB.
D. The detection of firmware file may be disrupted by other files on your USB. It is recommended that you wipe the USB or reformat it to NTFS format.
Reformat your USB by using HP USB
Storage Format Tool:
1. Disconnect your USB from the Capture Box. Connect it to a computer.
2. Download HP USB Storage Format Tool at the following link:
http://download.cnet.com/HP-USB-Disk-Storage-Format-Tool/3000-2094_4-10974082.html
3. Undergo HP USB Storage Format Tool. Select your USB and format it to NTFS format.
Save the firmware file into the NTFS USB and reconnect it to the Capture Box to upgrade firmware.

If the problem still persists, refer to FAQ at www.avermedia.com for further troubleshooting.

Documents / Resources

AVerMedia C285 Game Capture HD II Video Streaming and Capture Device [pdf] User Manual
C285, C285 Game Capture HD II Video Streaming and Capture Device, Game Capture HD II Video Streaming and Capture Device, Video Streaming and Capture Device, Capture Device

References

Leave a comment

Your email address will not be published. Required fields are marked *