AUTOOL BT10
EPB Release Tool
User Manual
COPYRIGHT INFORMATION
Copyright
- All rights reserved by AUTOOL TECH. CO., LTD. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of AUTOOL. The information contained herein is designed only for the use of this unit. AUTOOL is not responsible for any use of this information as applied to other units.
- Neither AUTOOL nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this unit, or failure to strictly comply with AUTOOL operating and maintenance instructions.
- AUTOOL shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as original AUTOOL products or AUTOOL approved products by AUTOOL.
- Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
AUTOOL disclaims any and all rights in those marks. 。
Trademark
- Manual are either trademarks, registered trademarks, service marks, domain names, logos, company names or are otherwise the property of AUTOOL or its affiliates. In countries where any of the AUTOOL trademarks, service marks, domain names, logos
and company names are not registered, AUTOOL claims other rights associated with unregistered trademarks, service marks, domain names, logos, and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or ompany name of AUTOOL or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name. You may contact AUTOOL by visiting AUTOOL at https://www.autooltech.com, or writing to aftersale@autooltech.com, to request written permission to use materials on this manual for purposes or for all other questions relating to this manual.
SAFETY RULES
General safety rules
- Always keep this user manual with the machine.
- Before using this product, read all the operational instructions in this manual. Failure to follow them may result in electric shock and irritation to skin and eyes.
- Each user is responsible for installing and using the device according to this user manual. The supplier is not responsible for damage caused by improper use and operation.
- This device must only be operated by trained and qualified personnel. Do not operate it under the influence of drugs, alcohol, or medication.
- This machine is developed for specific applications.
- The supplier points out that any modification and/or use for any unintended purposes is strictly prohibited.
- The supplier assumes no express or implied warranties or liabilities for personal injury or property damage caused by improper use, misuse, or failure to follow safety instructions.
- This device is intended for use by professionals only.
Improper use by non-professionals may result in injury or damage to the tools or workpieces. - Keep out of reach of children.
- When operating, ensure nearby personnel or animals maintain a safe distance. Avoid working in rain, water, or damp environments. Keep the work area well-ventilated, dry, clean, and bright.
Handling
Used/damaged device must not be disposed of in household waste but must be disposed of in an environmentally friendly manner. Use designated electrical device collection points.
Electrical safety rules 
Do not twist or severely bend the power cable, as this may damage the internal wiring. If the power cable shows any signs of damage, do not use the device. Damaged cables pose a risk of electrical injury. Keep the power cable away from heat sources, oil sources, sharp edges, and moving parts. Damaged power cables must be replaced by the manufacturer, their technicians, or similarly qualified personnel to prevent hazardous situations or injury.
Equipment safety rules 
- Never leave the device unattended when it is powered on. Always disconnect the power cable and ensure the device is turned off when it is not being used for its intended purpose!
- Do not attempt to repair the device yourself.
- Before connecting the device to power, check that the battery voltage matches the value specified on the nameplate. Mismatched voltage can cause serious hazards and damage the device.
- It is essential to protect the device from rainwater, moisture, mechanical damage, overload, and rough handling.
Application
- Before use, check the power cord, connection cables for any damage. If any damage is found, do not operate the device.
- Use the device only in compliance with all safety instructions, technical documents, and vehicle manufacturer specifications.
- If replacement accessories are needed, use only brand new and unopened products.
Personnel protection safety rules 
- Protective gear may be worn when using this product.
- Do not connect or disconnect any test device while the ignition switch is on or the engine is running.
- Always ensure you have a stable footing to safely control device in case of emergencies.
PRODUCT INTRODUCTION
Product Features
- Emergency drive system for EPB with a core processor.
- Dual-channel control for forward and reverse rotation, capable of releasing or applying the EFB in both directions.
- Reverse polarity protection, system does not work if the positive and negative terminals are reversed.
- Power-on Indicator, with the power indicator light turning on when the power is correctly connected.
- Over-current protection (includes a 5A fast-blow f use).
Technical Specifications
| Working Voltage | DC 10V~14V |
| Working Current | ＜15A |
PRODUCT STRUCTURE
Structural Diagram
| A | Power Clamp | B | Built-in 5A Fuse |
| C | Power Indicator Light | D | Motor Braking |
| E | Motor Release | F | Electronic Parking Brake Terminal Interface |
OPERATING STEPS
- Prepare a fully charged spare battery.
- Check that the fuse is intact and not blown.
- Connect the power clamps securely to the positive and negative terminals of the spare battery (red clamp to positive, black clamp to negative). When connected correctly, the power indicator light will turn on.
- Connect the EPB terminal of the device to the vehicle’s external EFB drive port.
- Press the rocker switch to position “I” to start the motor for braking. The brake caliper will begin to tighten. Once you release the switch, the button will automatically reset. Pay attention to the motor sound—when the motor reaches the end of its stroke, the brake caliper will be fully engaged.
Continuing to drive the motor may cause damage.
To protect the motor, the fuse will blow. - Press the rocker switch to position “II” to start the motor for releasing. The brake caliper will begin to loosen. Once you release the switch, the button will automatically reset. Pay attention to the motor sound—after the motor has fully released, it will begin to run idle. You should release the switch promptly at this point.
- If the behavior when pressing the rocker switch does not match the description, it is possible that the motor ‘s forward and reverse directions are reversed. Please pay special attention to this.
MAINTENANCE SERVICE
Our products are made of long-lasting and durable materials, and we insist on perfect production process. Each product leaves the factory after 35 procedures and 12 times of testing and inspection work, which ensures that each product has excellent quality and performance.
Maintenance
To maintain the performance and appearance of the product, it is recommended that the following product care guidelines be read carefully：
- Be careful not to rub the product against rough surfaces or wear the product, especially the sheet metal housing.
- Please regularly check the product parts that need to be tightened and connected. If found loose, please tighten it in time to ensure the safe operation of the equipment. The external and internal parts of the equipment in contact with various chemical media should be frequently treated with anti-corrosion treatment such as rust removal and painting to improve the corrosion resistance of the equipment and extend its service life.
- Comply with the safe operating procedures and do not overload the equipment. The safety guards of the products are complete and reliable.
- Unsafe factors are to be eliminated in time. The circuit part should be checked thoroughly and the aging wires should be replaced in time.
- When not in use, please store the product in a dry place. Do not store the product in hot, humid, or non-ventilated places.
WARRANTY
From the date of receipt, we provide a three-year warranty for the main unit and all the accessories included are covered by a one-year warranty.
Warranty access
- The repair or replacement of products is determined by the actual breakdown situation of product.
- It is guaranteed that AUTOOL will use brand new component, accessory or device in terms of repair or replacement.
- If the product fails within 90 days after the customer receives it, the buyer should provide both video and picture, and we will bear the shipping cost and provide the accessories for the customer to replace it free of charge. While the product is received for more than 90 days, the customer will bear the appropriate cost and we will provide the parts to the customer for replacement free of charge.
These conditions below shall not be in warranty range - The product is not purchased through official or authorized channels.
- The product breakdown because the user does not follow product instructions to use or maintain the product.
We AUTOOL pride ourselves on superb design and excellent service. It would be our pleasure to provide you with any further support or services.
Disclaimer
- All information, illustrations, and specifications contained in this manual, AUTOOL resumes the right of modify this manual and the machine itself with no prior notice. The physical appearance and color may differ from what is shown in the manual, please refer to the actual product. Every effort has been made to make all descriptions in the book accurate, but inevitably there are still inaccuracies, if in doubt, please contact your dealer or AUTOOL after-service centre, we are not responsible for any consequences arising from misunderstandings.
RETURN & EXCHANGE SERVICE
Return & Exchange
- If you are an AUTOOL user and are not satisfied with the AUTOOL products purchased from the online authorized shopping platform and offline authorized dealers, you can return the products within seven days from the date of receipt; or you may exchange it for another product of the same value within 30 days from the date of delivery.
- Returned and exchanged products must be in fully saleable condition with documentation of the relevant bill of sale, all relevant accessories and original packaging.
- AUTOOL will inspect the returned items to ensure that they are in good condition and eligible. Any item that does not pass inspection will be returned to you and you will not receive a refund for the item.
- You can exchange the product through the customer service center or AUTOOL authorized distributors; the policy of return and exchange is to return the product from where it was purchased. If there are difficulties or problems with your return or exchange, please contact AUTOOL Customer Service.
| China | 400-032-0988 |
| Oversea Zone | +86 0755 23304822 |
| aftersale@autooltech.com | |
| https://www.facebook.com/autool.vip | |
| YouTube | https://www.youtube.com/c/autooltech |
EU DECLARATION OF CONFORMITY
We as the manufacturer declare that the designated product: EPB Release Tool (BT10)
Complies with the requirements of the: EMC Directive 2014/30/EU
RoHS Directive 2011/65/EU + 2015/863 + 2017/2102 Applied Standards:
EN IEC 61326-1:2021, EN IEC 61000-3-2:2019 +
A1:2021, EN 61000-3-3:2013 + A1:2019 + A2:2021
IEC 62321-3-1:2013, IEC 62321-5:2013, IEC
62321-4:2013+A1:2017, IEC 62321-7-1:2015,IEC
62321-7-2:2017, IEC 62321-1:2013, IEC
62321-6:2015, IEC 62321-8:2017
Certificate No.: ZHT-230925028C, ZHT-230925030C
Test Report No.: ZHT-230925028E, ZHT-230925030R
Manufacturer
Shenzhen AUTOOL Technology Co, Ltd.
Floor 2, Workshop 2, Hezhou Anle Industrial Park, Hezhou Community, Hangcheng Street, Bao ‘an District, Shenzhen
Email: aftersale@autooltech.com
COMPANY NAME: XDH Tech
ADRESS: 2 Rue Coysevox Bureau 3, Lyon, France
E-MaiL: xdh.tech@outlook.com
CONTACT PERSON: Dinghao Xue
AUTOOL TECHNOLOGY CO.,LTD
www.autooltech.com
aftersale@autooltech.com
+86-755-2330 4822 / +86-400 032 0988
Unit 1303, Building 1, Runzhi R&D Center,
Bao’an, Shenzhen, China
Corporate Standard: Q/OR 003-2023
http://www.autooltech.com
https://www.facebook.com/AUTOOL.vip/
Documents / Resources
 |
AUTOOL BT210 EPB Release Tool [pdf] User Manual BT210, BT210 EPB Release Tool, EPB Release Tool, Release Tool |