4B Solar Single Camera
Product Information
Specifications
- Camera Modulation Mode: OFDM/CCK
- Operating Voltage: DC 3.4-4.2V
- Operating Current: Max 900mA (@4.2V)
Operating Conditions
Input: 5V2A
Charging Instructions
The camera takes approximately 6.5 hours to fully charge. When
charging, the red indicator light will stay on. Once fully charged,
the red light will turn off. Use a standard charger with a rated
output of 2A or higher for proper charging.
Installation Instructions
Fixed Mount Installation for Camera
- Use a drill to install the camera mounting base onto the
vehicle using four self-tapping screws. - Align the camera clips with the slots on the mounting base and
press down to secure it. - Insert the anti-theft screw and tighten with the included hex
wrench.
Magnetic Mount Installation for Camera
Note: Ensure the installation surface is metal. Attach the
camera magnetically onto the iron plate.
Pairing Instructions
- Press Menu (M) button on the main screen to open the main menu
and select Pair. - Select Cam1 or Cam2, press (M), and turn on the camera within
1-2 seconds for automatic pairing. - If not successful within 30s, repeat as needed.
Troubleshooting
Problem: Camera and monitor will not pair
Solution: Check designated cameras, power, LED
status, pairing mode, antenna, obstructions, nearby electronics
interference.
Problem: Blurry display, Image too dark/bright,
Poor night vision
Solution: Remove lens protective film, clean lens,
adjust brightness/contrast, check for obstructions, ambient light
interference, maintain distance from license plate lights.
FAQ
Q: Can I use this backup camera kit on any
vehicle?
A: These installation instructions are provided as
a general guide only and may not be applicable to all vehicle
types. It is recommended to check compatibility before
installation.
Digital Wireless Backup Camera kit
English User Manual
Introduction
Thank you for purchasing our backup camera. Please read all installation instructions carefully before starting. Improper installation may void the manufacturer’s warranty. These installation instructions are not applicable to all vehicle types and are provided as a general guide only.
æ
Contents
Package Contents …………………………………………………………………………………………………………………………. 1 Specifications ………………………………………………………………………………………………………………………………… 2 Operating Conditions …………………………………………………………………………………………………………………….. 3 Troubleshooting …………………………………………………………………………………………………………………………….. 6 Warranty Information ……………………………………………………………………………………………………………………… 8
Package Contents
ç
æ
æ
æ
Camera
ç
USB Charging Cable for Camera
Camera Mount
ç
ç
Magnetic Camera Base
Hex Wrench
Antenna
Self-tapping Screws
Anti-theft Screws
Digital Wireless Backup Camera kit
English User Manual
User Manual
1
Specifications
Camera
æ Antenna ç Light Sensor è Lens é Indicator Light ê Infrared Light ë Charging Port ì Power Button í Base
ç
è
é
æ
ê
ëì í
Camera Modulation Mode: Operating Voltage: Indicator Light Status
OFDM/CCK DC 3.4-4.2V
Operating Current:
Max 900mA (@4.2V)
Off: Camera is off or in sleep mode Lights up for 10s then off: Power on prompt, enters sleep if idle Blinking: Pairing mode Steady On: Successfully connected to display Blinks once: Power switch in transition
2
ç
Operating Conditions
Camera Installation
Input5V2A
Jump starter
Power Plug
Charging indicator
Note: The camera takes approximately 6.5 hours to fully charge.
When charging, the red indicator light will stay on. Once fully charged, the red light will turn off.
Please use a standard charger with a rated output of 2A or higher to ensure proper charging.
(In dim lighting conditions, the red indicator may glow faintly even after the battery is fully charged.)
3
Fixed Mount Installation for Camera
1
2
3
4
1.Use a drill or other professional tools to install the camera mounting base onto the vehicle using four self-tapping screws (see Figure 1).
2.Align the two clips at the bottom of the camera with the slots on the mounting base, then press the camera down to s ecure it (see Figures 2 and 3).
3.Insert the anti-theft screw into the hole, and tighten it with the included hex wrench (see Figure 4).
Magnetic Mount Installation for Camera
æ
ç
4
æ Align the two clips at the bottom of the camera with the slots on the top of the mounting base, then press the camera
downward to secure it.
Note: Ensure the installation surface is made of metal. The magnetic base will not attach properly to non-metal surfaces.
çThe camera angle can be adjusted up and down as needed.
èIf you have purchased the iron plate mount, install the iron plate onto the vehicle body first,
then attach the camera magnetically onto the iron plate.
è
Metal Plate
Pairing Instructions By default, the monitor is not paired with any camera. If no camera is connected within 10 seconds, the screen will turn off and enter standby.
To pair Cam1/Cam2 1. On the main screen, press the Menu (M) button to open the main menu. Use or to select “Pair”. Press (M) to enter
pairing submenu. 2. Select Cam1 or Cam2 using or and press (M). The indicator will flash rapidly. 3. Within 1-2 seconds, turn on the camera by pressing its power button. Pairing will complete automatically.
If not successful within 30s, the monitor will exit pairing mode. Repeat as needed.
5
Troubleshooting
Problem Camera and monitor will not pair
Intermittent video
Solution Monitor only pairs with designated cameras Check camera power and LED status Ensure camera and monitor are both in pairing mod Check antenna installation Remove large or dense obstructions Turn off nearby electronics Interference from multiple power lines may occur Try re-pairing
6
Problem Blurry display Image too dark/bright Poor night vision
Solution Remove lens protective film Clean lens with a soft cloth Bad weather like fog/rain/dust may obscure vision; clean camera Adjust brightness/contrast Bright image from direct light source is not a fault Clean light sensor or remove obstructions Strong ambient light may disable night vision (not a fault) Keep at least 2 inches away from license plate lights
7
Warranty Information
Dear Customer, thank you for choosing our product. This device comes with a 12-month warranty.
Warranty Coverage If the product experiences failure due to non-human factors within 12 months of purchase, we offer free repair, replacement, or equivalent warranty service. Exclusions Warranty does not cover damage caused by: – Accidental drops, impacts, or water ingress – Unauthorized disassembly, modification, or repair – Use of improper accessories or power supplies – Misuse, overuse, or neglecting instructions
8
Ver-1.0
Documents / Resources
 |
AUTO-VOX 4B Solar Single Camera [pdf] User Manual 4B Solar Single Camera, 4B, Solar Single Camera, Single Camera |