Audionic Hammer Wireless Headphone
Specifications
| Bluetooth Version | V6.0 |
| Bluetooth Range | 33 ft (10 m) |
| Charging Port | Type-C |
| Play Time | Up to 15 hours (ANC ON, max volume); up to 20 hours (ANC OFF, max volume) (Varies depending on settings and usage) |
| Charging Time | Approx. 2 hours |
| Battery Capacity | 200mAh |
| Sensitivity | 105 +/- 3dB |
| Driver Size | 40mm |
| Impedance | 32 ohms |
| Frequency Response | 20 Hz – 20 kHz |
Wireless Headphone Overview
This wireless headphone supports Bluetooth audio with ANC (Active Noise Cancellation), call controls, and wired playback via a Type-C cable. You can charge using the included Type-C port and control playback and volume with the headphone buttons.
Operation Instructions
Power On
Long press 3 seconds the multi-function button. A tone will be heard. The LED indicator will turn blue.
Bluetooth Pairing
The LED indicator will flash Red and Blue lights indicate that enter bluetooth pairing mode. Choose the pairing name “BSHP1270” to pair with your device. Once successful, a tone will be heard indicating that the headphone paired. After pairing successfully, BLUE lights will slowly flash every 5 seconds.
(The headphones will automatically reconnect to the device they were most recently paired to, so long as that device is within connection range(33ft) and Bluetooth is enabled)
- “+”button：short press to increase the volume. Long press to skip to the next track.
- “-” button: short press to decrease the volume. Long press to skip to the previous track.
“Multi-function” button:
- a. Short press to play/pause the music.
- b. When there is an incoming call, short press to answer; short press again to hang up the call.
- c. Long press to reject.
- d. Quick press twice to recall your last dialed phone number.
ANC Function
Press the ANC button to turn on the function. Press the ANC button again to turn off the function. When ANC is ON, the indicator will turn on a green light.
To be a wired Headphone
Plug in the included Type-C cable and connect to your device to use it as a wired headphone
Power Off
- a. Long press 3 seconds the multi-function button. A tone will be heard.
- b. Automatically power off if it fails to connect with any device within 5 minutes (when ANC is in OFF status).
- c.The headphone will automatically shut down when charging.
Charging
On low power, a tone will be heard, indicating that the headphone should be charged. The LED indicator will turn RED while charging and turn BLUE when fully charged.
Troubleshooting
- Can’t connect / pairing seems to fail: The headphone will automatically power off if it fails to connect with any device within 5 minutes (only when ANC is turned OFF). Turn ANC OFF, power back on, and try pairing again.
- Charging behavior: If the battery is low, an audio tone indicates the headphone needs charging. During charging, the LED shines RED, and it turns BLUE when fully charged.
- Headphone turns off unexpectedly: The device will power off when charging is initiated, or when you long-press the multi-function button for 3 seconds.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Documents / Resources
 | Hammer Wireless Headphone |
References
- User Manualmanual.tools