audiocodes KAC-CAM-360 Video Conferencing Camera User Guide

Press and hold KAC-CAM-360’s wireless connection button for 8 seconds to enter RC pairing mode.
Verify the connection by pressing and holding the RC’s wireless connection button for 3 seconds.

Frequently Asked Questions (FAQ):

Q: What should I do if the device does not power on?
A: Check the power supply connection and ensure it is connected properly. Try using a different power adapter if needed.

Quick Guide

Welcome
Congratulations on purchasing your AudioCodes Kramer KAC-CAM-360 Video Conferencing Camera!
In this Manual, the following marketing names are interchangeable:

KAC-CAM-360	RXVCam360
KAC-CU-200	RXV-200
KAC-TCH-10	RX-PAD

Checking Package Contents

Before installing your KAC-CAM-360, make sure these items are included in your shipped box:

USB Cable×1
Remote Control (RC)×1

Power Adapter×1
Power Adapter Plug×5

Connecting KAC-CAM-360 to KAC-CU-200 + KAC-TCH-10

Use the diagram as reference when connecting KAC-CAM-360 to KAC-CU-200 Intelligent Android A/V Hub.

You can alternatively select camera mode using KAC-CAM-360’s Device button -OR- the RC’s Mode Switching button.

Connecting KAC-CAM-360 to PC/Laptop

Connect KAC-CAM-360 to PC/laptop using the figure below as reference:

To connect KAC-CAM-360 to PC/laptop:

Connect the power adapter to the KAC-CAM-360 camera and then press the power button to switch on the device; the ring light lights up and the running light indicates the device is booting up. A prompt tone is played when boot-up is complete.

Connect the USB cable to the PC/laptop and press the Mode Switching button to select an operational mode described here.

The camera must be connected to a 12V power supply to function correctly.

Pairing RC with KAC-CAM-360
You need to pair the RC with KAC-CAM-360.

To pair the RC with KAC-CAM-360:

Press and hold the KAC-CAM-360’s wireless connection button for 8 seconds to enter RC pairing mode.
Verify the device is connected to the RC and can be controlled via the RC: Press and hold the RC’s wirelessconnection button for 3 seconds. If there is a prompt tone, it means the device is connected.

Use the following table as reference to the preceding figure.

Choosing Operational Mode

Choose one of five available Operational Modes. Use the table below as reference.

Monitoring Camera Status

Status	Description
Light ring	[Boot-up] After the white lights fully lights up, a blue running light appears until boot-up is complete. [Shut-down] The blue light gradually goes off after all of them light up. Volume adjustment] The blue lights indicate the volume level. [DOA] The direction indicator shows the blue light.
Power switch	Press and hold for two seconds to power on; the white light stays on continuously. Press and hold for two seconds to power off; the red light stays on continuously.
Camera switch	Short-press to turn on the camera; the white light stays on continuously. Short-press to turn off the camera; the red light stays on continuously.
Mute	Short-press to turn on the microphone; the white light stays on continuously. Short-press to turn off the microphone; the red light stays on continuously.

Status	Description
Mode switch	§ Short-press for the white light to flash and switch between modes.
Wireless connection	[RC wireless connection] Press and hold the RC’s wireless connection button for eight seconds and the RC’s wireless connection button for three seconds to enter RC pairing mode; the white light flashes fast; When pairing is successful, the blue light stays on continuously; press and hold for eight seconds to cancel RC pairing; the white light flashes fast. [Wireless audio connection (optional)] Press and hold for two seconds to start the wireless audio connection; the blue light blinks. Press and hold for another two seconds to disconnect the wireless audio connection; the blue light flashes. Press and hold for two seconds to turn off the wireless audio connection; the white light stays on continuously. When the wireless audio connection fails, the white light stays on continuously. When the wireless audio connection is successful, the blue light stays on continuously.

Configuring Camera Settings

To configure camera settings:
On the RC, press the Menu key to enter the following function adjustments:

Setting	Default	Range
Brightness	6	0-12
Sharpness	1	0-6
Contrast	115	0-255
Saturation	3	0-6
Autoframing sensitivity	Normal	Low，Normal，High
Frequency	60Hz	50Hz , 60Hz
Image Flip	Normal	Normal \H \ V\ H+V
OSD Flip	Normal	Normal \H \ V\ H+V
Reset	/	One-click restore

International Headquarters

2 Negev Street,
Airport City
Lod 7019900, Israel
Tel: +972 073 2650200
Mail: Info@kramerav.com

Contact us: https://www.kramerav.com/contact-us/
Website: https://www.kramerav.com/
©2024 AudioCodes Ltd. All rights reserved. AudioCodes, AC, HD VoIP, HD VoIP Sounds Better, IPmedia, Mediant, MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice, AudioCodes Meeting Insights, AudioCodes Room Experience are trademarks or registered trademarks of AudioCodes Limited. All other products or trademarks are property of their respective owners. Product specifications are subject to change without notice.

FCC Warning
Prior to operating KAC-CAM-360 and AudioCodes Kramer devices for Teams Rooms on Android, refer to the regulatory information documents.

Notice Information

Information contained in this document is believed to be accurate and reliable at the time of printing. However, due to ongoing product improvements and revisions, AudioCodes Kramer cannot guarantee accuracy of printed material after the Date Published nor can it accept responsibility for errors or omissions.
Updates to this document can be downloaded from https://www.kramerav.com/

This document is subject to change without notice. Date Published: November-9-2024

Documents / Resources

audiocodes KAC-CAM-360 Video Conferencing Camera [pdf] User Guide
KAC-CAM-360, KAC-CAM-360 Video Conferencing Camera, Video Conferencing Camera, Conferencing Camera, Camera

References

User Manual

audiocodes KAC-CAM-360 Video Conferencing Camera

Product Usage Instructions