Important Safety Information
Please read this entire manual carefully before assembly and use. Failure to follow these instructions may result in injury or damage to the product. Keep this manual for future reference.
- Always wear appropriate safety gear, including gloves and eye protection, during assembly.
- Assembly typically requires two or more people. Do not attempt to assemble alone.
- Ensure the shed is anchored securely to the ground to prevent tipping in high winds.
- Keep children and pets away from the assembly area.
- Do not store flammable liquids or hazardous materials inside the shed.
- Regularly inspect the shed for any signs of damage or loose components.
Package Contents
Before beginning assembly, verify that all parts are present and undamaged. Refer to the packing list provided with your shed for a complete inventory. The following image illustrates the shed's dimensions and included accessories.

This image illustrates the shed's dimensions: 67.5 inches wide, 72.4 inches high (front), 61.8 inches high (back), 41.3 inches deep (roof), 37.6 inches deep (base), and 14.57 square feet of storage space. It also indicates that two pairs of gloves are included for assembly.
Setup Instructions
1. Site Preparation
- Choose a level, firm, and well-drained area for the shed. An uneven surface can cause assembly difficulties and structural instability.
- Clear the area of any debris, rocks, or vegetation.
- Consider laying a foundation such as a concrete slab or treated timber frame for added stability and moisture protection.
2. Assembly Steps
Follow the detailed step-by-step instructions and diagrams provided in your separate assembly guide. The general sequence is as follows:
- Unpack and Identify Parts: Lay out all components and hardware. Familiarize yourself with each part using the provided parts list.
- Assemble Base Frame: Construct the base frame on your prepared site, ensuring it is square and level.
- Attach Wall Panels: Secure the wall panels to the base frame, working from one corner. Ensure panels are correctly oriented.
- Install Roof Structure: Assemble and attach the roof support beams and then the roof panels. Ensure the sloping roof is correctly positioned for water runoff.
- Install Doors and Locking Mechanism: Attach the sliding doors to their tracks and install the lockable latch mechanism.
- Secure Shed: Anchor the shed to the ground using appropriate anchors (not included) to prevent movement due to wind.
Operating Instructions
1. Door Operation
- The shed features sliding doors. To open, gently slide the door along its track. To close, slide it back until it meets the other door or the frame.
- The door is equipped with a lockable latch. Use a padlock (not included) to secure the shed.
2. Ventilation
- The shed includes built-in vents near the roofline to promote air circulation and reduce condensation. Ensure these vents are not obstructed.
Maintenance
1. Cleaning
- Clean the exterior of the shed periodically with a mild soap and water solution. Rinse thoroughly with clean water.
- Avoid using abrasive cleaners, harsh chemicals, or stiff brushes, as these can damage the finish.
- Keep the door tracks free of dirt and debris to ensure smooth operation.
2. Inspection
- Periodically check all nuts, bolts, and screws for tightness. Tighten any loose fasteners.
- Inspect the panels and roof for any signs of damage, rust, or wear. Address any issues promptly to prevent further deterioration.
3. Winter Care
- While designed for Canadian weather, it is advisable to remove heavy snow accumulation from the roof to prevent excessive load.
- Ensure proper drainage around the base of the shed to prevent water from pooling and potentially freezing against the structure.
Troubleshooting
- Issue: Doors not sliding smoothly.
Solution: Check the door tracks for any debris (leaves, dirt, small stones) and clear them. Apply a silicone-based lubricant to the tracks if necessary. Ensure the shed is level. - Issue: Water leakage inside the shed.
Solution: Inspect all roof and wall panel seams for proper alignment and sealing. Ensure all fasteners are tight. Verify that the shed is installed on a level surface and that water drains away from the base. - Issue: Shed feels unstable or wobbly.
Solution: Re-check all assembly fasteners to ensure they are securely tightened. Confirm that the shed is properly anchored to the ground as recommended in the setup instructions. Ensure the base is level.
Specifications
| Feature | Detail |
|---|---|
| Model Number | TM-G37004-0804BK |
| Brand | Nordivale |
| Product Dimensions (D x W x H) | 101D x 80W x 90H centimetres (approx. 39.8D x 31.5W x 35.4H inches) |
| Item Weight | 55 kg (approx. 121 lbs) |
| Material | Triple-galvanized steel with rustproof coating |
| Roof Type | Sloping |
| Features | Water-resistant, Lockable Door, UV-resistant panels, Structural bracing |
| Storage Area | 14.57 sq.ft |
Warranty Information
This Nordivale Outdoor Metal Storage Shed is covered by a manufacturer's warranty. Please refer to the warranty card included with your product packaging or visit the official Nordivale website for detailed terms and conditions regarding coverage, duration, and claims procedures.
Customer Support
Should you encounter any issues during assembly or operation, or if you have questions not covered in this manual, please contact Nordivale customer support. Have your model number (TM-G37004-0804BK) and purchase information ready for faster assistance.
Contact information can typically be found on the product packaging or the manufacturer's official website.