HLead Touchscreen Paraffin Wax Machine User Manual

Introduction

Thank you for choosing the HLead Touchscreen Paraffin Wax Machine. This manual provides essential information for the safe and effective operation, maintenance, and care of your new paraffin wax warmer. Please read these instructions thoroughly before first use and retain them for future reference.

Important Safety Information

WARNING: To reduce the risk of burns, electrocution, fire, or injury to persons:

• Always unplug the appliance from the electrical outlet immediately after using and before cleaning.
• Do not use or make contact with paraffin wax that is higher than 115°F (46°C).
• Safest to use with a paraffin machine with digital degree temperature setting.
• Do not use wax warmer that does not digitally display the temperature setting, as the wax may overheat and contact with it may burn the skin.
• Intended for use as medical therapy and/or beauty applications.
• Keep out of reach of children.
• Do not immerse the unit in water or other liquids.
• Do not operate if the cord or plug is damaged.

Package Contents

Verify that all items are present and in good condition upon unpacking:

• 1 x HLead Paraffin Wax Machine
• 3 x 200g Paraffin Wax Packs
• 1 x Pair Thermal Gloves
• 1 x Pair Thermal Boots
• 100 x PE Liners (Plastic Gloves)
• 1 x Brush
• 1 x Shovel/Spatula
• 1 x Heat-Insulating Grid

Setup

1. Placement: Place the paraffin wax machine on a stable, flat, heat-resistant surface. Ensure it is away from water sources and out of reach of children.
2. Initial Cleaning: Before first use, wipe the inside of the wax pot with a damp cloth. Ensure it is completely dry before adding wax.
3. Add Wax: Place the heat-insulating grid at the bottom of the wax pot. Add 2-3 packs of paraffin wax (approximately 400-600g) into the machine. For hands, a minimum of 4 packs (800g) is recommended. For feet, a maximum of 8 packs (1600g) can be used.
4. Power Connection: Plug the machine into a standard 110V/60Hz electrical outlet.

Operating Instructions

1. Melting the Wax

1. Press the power button on the touchscreen control panel to turn on the machine.
2. Set the desired temperature using the '+' and '-' buttons. The machine can heat wax up to 167°F (75°C). For quick melting, set to the maximum temperature.
3. The wax will fully dissolve in approximately 15-30 minutes, depending on the amount of wax and initial temperature setting.
4. Once the wax is melted, it is recommended to lower the temperature to 113-122°F (45-50°C) for safe and comfortable use, especially for sensitive skin. Long-press the temperature button to toggle between Fahrenheit (°F) and Celsius (°C).

2. Applying the Wax

1. Ensure the wax has reached a safe and comfortable temperature (113-122°F / 45-50°C).
2. Slowly dip your hand, foot, or elbow into the melted paraffin wax. Immediately withdraw and allow the wax to solidify slightly.
3. Repeat the dipping process 3-5 times to build up a thick layer of wax.
4. Immediately after the final dip, place a PE liner (plastic glove/boot) over the waxed area.
5. For enhanced heat retention, put on the thermal glove or boot over the plastic liner.
6. Allow the wax to remain on your skin for approximately 15-20 minutes. This allows the skin to fully absorb the nutrients and benefit from the warmth.

3. Removing the Wax

1. After 15-20 minutes, remove the thermal glove/boot and the plastic liner. The wax should peel off easily with the liner.
2. Discard the used wax and plastic liner. Do not reuse wax that has been in contact with skin for hygiene reasons.
3. Enjoy your smooth and soft skin.

4. Timer Settings

The machine features 4 auto-shutoff timer options to customize your treatment duration:

• 0.5 hours (30 minutes) - Quick/Local care
• 1.0 hour (60 minutes) - Body/Daily care
• 1.5 hours (90 minutes) - Special care
• 2.0 hours (120 minutes) - Professional nourishment

Once the wax is melted, you can activate the 'Keep-Warm' mode or select a timer setting to maintain the desired temperature for multiple users or extended sessions.

Maintenance and Cleaning

1. Power Off: Always unplug the machine from the power outlet before cleaning.
2. Wax Removal: After use, if there is remaining wax, slightly heat it to loosen it from the pot. Once loosened, carefully pour out the wax.
3. Recycling Wax: The used wax can be collected and recycled until it becomes unclear or contaminated.
4. Cleaning the Pot: Use a clean, dry cloth to wipe the melting pot and the heat-insulating grid. Do not use abrasive cleaners or immerse the unit in water.
5. Exterior Cleaning: Wipe the exterior of the machine with a soft, damp cloth.
6. Storage: Store the machine in a cool, dry place when not in use.

Troubleshooting

Specifications

Warranty and Support

For warranty information or technical support, please refer to the documentation included with your purchase or contact the manufacturer directly. You may also reach out to the seller through the platform where the product was purchased.