NPET Wireless Pet Water Fountain Instruction Manual

1. Introduction

Thank you for choosing the NPET Wireless Pet Water Fountain. This fountain is designed to provide fresh, filtered water for your pets, encouraging healthy hydration. Featuring a large 5.5L capacity, a 4000mAh rechargeable battery for wireless operation, and three intelligent modes (Sensor, Timer, Continuous), this fountain offers convenience and peace of mind. Its ultra-quiet pump and BPA-free construction ensure a safe and comfortable drinking experience for both cats and dogs.

2. Safety Instructions

• Read all instructions carefully before use and retain for future reference.
• This appliance is intended for indoor household use only.
• Do not immerse the pump or electrical components in water beyond the specified cleaning instructions.
• Ensure the fountain is placed on a stable, level surface to prevent tipping.
• Keep the power cord (if used for charging) away from pets to prevent chewing.
• Use only the original charging cable and adapter provided with the product.
• Do not allow children to play with the fountain.
• Always unplug the fountain before cleaning or performing maintenance.
• If the fountain is damaged or malfunctions, discontinue use immediately and contact customer support.

3. Package Contents

Please check to ensure all items are present and in good condition:

• NPET Wireless Pet Water Fountain Base
• Wireless Pump Module
• Filter Tray
• Filter Element (5-layer filtration system)
• Charging Cable
• User Manual

4. Product Overview

The NPET Wireless Pet Water Fountain consists of a main water reservoir, a filter tray, and a wireless pump module. The pump module houses the motor, battery, and control panel with indicator lights for various functions and modes. A transparent window on the fountain base allows for easy monitoring of the water level.

Image: The fountain features a transparent window with MAX/MIN water level lines for easy monitoring. A cat and dog are shown near the fountain, highlighting its large 5.5L capacity.

Image: The wireless design allows flexible placement in different areas of your home, such as the living room, bedroom, or kitchen, without the need for power outlets or concerns about pets chewing on wires.

5. Setup

5.1 Initial Cleaning

Before first use, rinse all components (water reservoir, filter tray, pump module) with clean water. Do not use soap or harsh detergents on the pump module.

5.2 Filter Installation

Rinse the new filter element under running water for 2 minutes to remove any loose carbon dust. Place the rinsed filter into the filter tray.

Image: The 5-layer filtration system includes biochemical cotton, activated carbon, nano-silver, ion exchange resin, and non-woven fabric to ensure clean and fresh water for your pet.

5.3 Filling Water

Fill the water reservoir with clean water up to the 'MAX' line. Do not exceed the 'MAX' line to prevent overflow. Ensure the water level is above the 'MIN' line for proper pump operation.

5.4 Charging the Pump Module

The pump module contains a built-in 4000mAh rechargeable battery. For optimal performance, fully charge the pump module before first use. Connect the charging cable to the pump module and a suitable USB power adapter (not included). The charging indicator light will show the charging status.

Image: The fountain's 4000mAh battery provides long-lasting power, offering up to 50 days of operation in intermittent mode on a single charge.

5.5 Assembly

Place the filter tray with the installed filter into the water reservoir. Then, position the wireless pump module securely into its designated slot on the filter tray. Ensure it is firmly seated.

6. Operating Modes

The pump module features a power button that also functions as a mode switch. Long press for 2 seconds to power on/off. Short press to cycle through operating modes.

Image: The fountain offers two primary water modes: Timer Mode, which operates for 10 seconds every 10 minutes, and Sensing Mode, which activates for 10 seconds when a pet approaches within 50cm.

6.1 Timer Mode

In Timer Mode, the fountain will dispense water for 10 seconds every 10 minutes. This mode ensures regular water circulation and freshness throughout the day.

6.2 Sensing Mode

In Sensing Mode, the fountain activates when a pet approaches within approximately 50cm (19.68 inches) and dispenses water for 10 seconds. This conserves battery life and water, providing fresh water on demand.

Image: The all-in-one pump design simplifies refilling and cleaning, making maintenance incredibly easy.

6.3 Continuous Mode

If the fountain is connected to a power source via the charging cable, it will operate in Continuous Mode, providing a constant flow of water.

6.4 Indicator Lights

The pump module has indicator lights for:

• Sensing Mode: Indicates active sensing.
• Low Battery: Alerts when battery needs charging.
• Add Water: Indicates low water level.
• Timer Mode: Indicates active timer operation.

7. Maintenance

Regular cleaning and filter replacement are crucial for maintaining water quality and extending the life of your fountain.

7.1 Fountain Cleaning

Clean the water reservoir and filter tray weekly with water and a mild, pet-safe detergent. Rinse thoroughly to remove any residue.

Image: The fountain's design includes a splatter guard and a 10.62-inch wide tray to help keep your floor dry and clean, even with enthusiastic drinkers.

7.2 Pump Cleaning

The all-in-one pump module is designed for easy disassembly and cleaning. Disassemble the pump and clean all parts, including the impeller, with water and a small brush. Ensure no hair or debris is obstructing the impeller. Reassemble the pump after cleaning.

7.3 Filter Replacement

Replace the filter element every 2-4 weeks, or more frequently if you have multiple pets or notice reduced water flow. Always rinse new filters before use.

8. Troubleshooting

• No water flow: Check if the water level is above the 'MIN' line. Ensure the pump module is correctly seated. Clean the pump and impeller for any obstructions. Check battery level.
• Pump is noisy: Ensure the water level is sufficient. Clean the pump and impeller as hair or debris can cause noise.
• Indicator lights not working: Ensure the pump module is charged. If charging, check the connection.
• Fountain not responding to pet: In Sensing Mode, ensure there are no obstructions between the pet and the sensor. The detection range is approximately 50cm.

9. Specifications

10. Warranty

This product comes with a 7-day warranty from the date of purchase. Please retain your proof of purchase for any warranty claims. The warranty covers manufacturing defects but does not cover damage caused by misuse, accident, or unauthorized modifications.

11. Customer Support

For any questions, concerns, or technical assistance, please contact NPET customer support. Refer to the product packaging or the NPET official website for the most up-to-date contact information.