QWORK Car Trunk LED Strip Light (Model WD46369) Instruction Manual

1. Introduction

Thank you for choosing the QWORK Car Trunk LED Strip Light. This 4-meter automatic sensing white LED strip is designed to provide enhanced illumination for your vehicle's trunk, improving visibility and convenience. Its flexible, cuttable, and waterproof design ensures a versatile and durable lighting solution for various car models, including SUVs and trucks.

Image 1.1: The QWORK Car Trunk LED Strip Light installed, illuminating a vehicle's trunk space.

2. Safety Information

• Read all instructions carefully before installation and use.
• Ensure the vehicle's power is off before attempting any electrical connections.
• Do not expose the LED strip to extreme temperatures or direct flame.
• When cutting the strip, always ensure the cut end is properly sealed with insulating tape to prevent short circuits and maintain water resistance.
• Keep out of reach of children.
• Do not attempt to modify the product beyond the designated cut points.

3. Package Contents

Please check the package for the following items:

• 1 x QWORK Car Trunk LED Strip Light (4 meters)
• (Note: Additional installation tools or tape may be required and are not included.)

4. Installation Guide

The QWORK Car Trunk LED Strip Light is designed for non-destructive installation, typically by pressing it into the existing trunk seal. Follow these steps for proper setup:

4.1 Preparation

• Clean the area where the LED strip will be installed, ensuring it is free from dust and debris.
• Measure the length required for your trunk. The 4-meter strip can be customized to fit various vehicle sizes.

4.2 Cutting the LED Strip (If Necessary)

Image 4.1: The flexible and cuttable design of the LED strip, along with simple plug-in power connection.

1. Identify the designated cut points on the LED strip. These are usually marked.
2. Using sharp scissors, carefully cut the strip at the desired length.
3. Important: After cutting, immediately seal the exposed end of the strip with insulating tape to maintain its waterproof properties and prevent electrical issues.

4.3 Power Connection

1. Step 1: Insert the connector into the original vehicle's terminal block to test for power, distinguishing between positive and negative terminals.
2. Step 4: Plug it back into the original vehicle headlight and tidy up the wiring. (Note: The image sequence suggests steps 1 and 4 are related to power connection, while 2 and 3 are for strip placement/trimming).

4.4 Mounting the LED Strip

Image 4.2: Step-by-step installation instructions for the QWORK Car Trunk LED Strip Light.

1. Step 2: When installing the light strip, the transparent light-emitting side should face outwards, towards the interior of the trunk.
2. Carefully press the silicone housing of the LED strip into the existing trunk seal around the perimeter of your trunk opening. The flexible design allows it to conform to curves.
3. Ensure the strip is securely seated and does not interfere with the trunk's closing mechanism.
4. Step 3: Trim off any excess material along the black line if needed, ensuring the cut end is sealed.

Image 4.3: Visual comparison demonstrating increased illumination and enhanced ambiance after installation.

5. Operation

The QWORK Car Trunk LED Strip Light features an automatic sensing control system. Once properly installed and connected to power:

• The LED strip will automatically illuminate when the vehicle's trunk is opened.
• The LED strip will automatically turn off when the vehicle's trunk is closed.
• This ensures hands-free operation and efficient power usage.

Image 5.1: The LED strip provides bright edge lighting, making it easy to use the trunk in low-light conditions.

6. Maintenance

• Cleaning: Use a soft, damp cloth to wipe the silicone surface of the LED strip. Avoid abrasive cleaners or solvents.
• Inspection: Periodically check the strip for any signs of damage, especially at the cut ends, to ensure the insulating tape remains intact.
• Flexibility: The reinforced silicone housing is designed to maintain flexibility, but avoid excessive bending or sharp folds that could damage the internal LEDs.

7. Troubleshooting

8. Specifications

Image 8.1: Dimensions of the LED strip light, including total length and width.

9. Warranty & Support

For warranty information and customer support, please refer to the documentation provided with your purchase or contact QWORK customer service directly through their official website or the retailer where the product was purchased. Keep your purchase receipt for warranty claims.