Introduction
This manual provides essential information for the safe installation, operation, and maintenance of your Cecotec Bolero Flux DT 907500 Decorative Extractor Hood. Please read these instructions carefully before using the appliance and keep them for future reference.
Safety Information
Always adhere to local regulations regarding the discharge of air. Ensure proper ventilation in the room when the extractor hood is used simultaneously with gas or other fuel-burning appliances. The appliance must be installed by a qualified technician. Do not flambé under the extractor hood. Regularly clean the grease filters to prevent fire hazards. Disconnect the appliance from the power supply before any cleaning or maintenance.
Product Overview
The Cecotec Bolero Flux DT 907500 is a 90 cm decorative extractor hood designed for kitchen ventilation. It features a matt black glass finish with copper details, a BLDC motor, and an A+++ energy efficiency rating.
Figure 1: Front view of the Cecotec Bolero Flux DT 907500 Extractor Hood.
Dimensions
Refer to the diagram below for detailed product dimensions.
Figure 2: Product dimensions. Width: 90 cm, Depth: 37 cm, Height: 39.2 cm.
Setup and Installation
The extractor hood is designed for wall mounting. It can operate in extraction mode (ducting air outside) or recirculation mode (filtering air and returning it to the kitchen). For recirculation mode, the included carbon filters must be installed.
Installation Requirements:
- Ensure adequate clearance above the cooking surface as per local regulations.
- The appliance requires a 220 Volt power supply.
- For extraction mode, a suitable ducting system must be in place.
- For recirculation mode, install the two carbon filters (included but not pre-installed).
Professional installation is recommended.
Operating Instructions
The hood features a Touch Control panel and Hand Movement Control for intuitive operation.
Control Panel Functions:
- Power On/Off: Activates or deactivates the hood.
- Speed Selection: Choose from 3 fan speeds.
- Booster Function: Activates maximum extraction power (Dual Booster).
- Light Control: Turns the LED lighting on or off.
- Air Cleaning Function: Initiates a cycle to purify the air.
- Timer: Sets a delayed shut-off for the hood.
Hand Movement Control:
Certain functions can be activated by specific hand gestures in front of the sensor. Refer to the full user manual for detailed gesture commands.
Wi-Fi Connectivity:
Connect the hood to your home Wi-Fi network to control it via the Cecotec app on your smartphone. Follow the instructions in the app for pairing and remote control features.
Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your extractor hood.
Cleaning Grease Filters:
The 5-layer aluminum grease filters should be cleaned regularly, depending on usage. They are dishwasher safe. Remove the filters by following the instructions in the full manual, wash them, and ensure they are completely dry before re-installing.
Replacing Carbon Filters (Recirculation Mode):
If using the hood in recirculation mode, the carbon filters need to be replaced periodically (typically every 3-6 months, depending on usage). Refer to the full manual for replacement instructions.
Exterior Cleaning:
Clean the exterior surfaces with a soft cloth and a mild, non-abrasive cleaner. Avoid harsh chemicals or abrasive materials that could damage the finish.
Troubleshooting
Before contacting customer support, review the following common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Hood does not turn on. | No power supply; appliance unplugged; circuit breaker tripped. | Check power connection; reset circuit breaker. |
| Low suction power. | Clogged grease filters; carbon filters saturated (recirculation mode); incorrect installation. | Clean grease filters; replace carbon filters; verify installation. |
| Excessive noise. | Loose components; improper ducting; foreign object in fan. | Check for loose parts; inspect ducting; contact service if noise persists. |
For issues not listed here or if problems persist, contact Cecotec customer support.
Specifications
Detailed technical specifications for the Cecotec Bolero Flux DT 907500 Extractor Hood.
| Brand | Cecotec |
| Model Number | A01_EU01_110309 |
| Product Dimensions (DxWxH) | 89.5P x 37l x 39.2H cm |
| Color | Matt Black |
| Special Features | Auto Fan Shut-Off, Grease Filter, Timer, Hand Movement Control, Wi-Fi |
| Noise Level | 54 Decibel |
| Mounting Type | Wall Mount |
| Voltage | 220 Volt |
| Number of Speeds | 3 |
| Electric Power | 123 watts |
| Filter Type | Mesh (Aluminum), Carbon (optional) |
| Item Weight | 14.48 Kilograms |
| Energy Efficiency Class | A+++ |
| Suction Capacity | 717.2 m³/h (with Dual Booster) |
| Components Included | Decorative Extractor Hood, User Manual, 2 Carbon Filters (Not Installed) |
Energy Label and Product Fiche
For detailed energy consumption and performance data, refer to the energy label and product fiche.
Figure 3: Energy Label for the Extractor Hood.
Figure 4: Product Data Sheet (Ficha del producto).
Further details can be found on the EPREL database: https://eprel.ec.europa.eu/qr/2383310
Warranty and Support
Warranty Information:
This product comes with a 3-year warranty. Please retain your proof of purchase for warranty claims. The availability of spare parts in the EU is guaranteed for 10 years.
Customer Support:
For technical assistance, warranty claims, or further inquiries, please contact Cecotec customer support. Contact details may vary by region. Refer to the official Cecotec website or your purchase documentation for the most up-to-date contact information.
Cecotec Manufacturer: CECOTEC INNOVACIONES, SL
Country of Origin: Spain
Website: www.cecotec.com
Email: legal@cecotec.es
Phone: +34 963 21 07 28