Introduction
Thank you for choosing GAOMON Counter Height Bar Stools. This manual provides essential information for the safe assembly, operation, and maintenance of your new bar stools. Please read these instructions carefully before assembly and retain them for future reference.
Safety Information
- Ensure all parts are present and undamaged before assembly. Do not use if any parts are missing or broken.
- Assemble the stools on a soft, clean surface to prevent scratches.
- Tighten all screws firmly, but do not overtighten. Periodically check and retighten fasteners as needed.
- Do not stand on the stools. Use them only for seating.
- The maximum weight capacity for each stool is 250 pounds. Do not exceed this limit.
- Keep small parts and packaging materials away from children.
Package Contents
Verify that all components listed below are included in your package. If any parts are missing or damaged, please contact customer support.
- Seat (with PU Upholstery)
- Backrest (X-Design)
- Leg Frames (Front and Rear)
- Footrest Bars
- Assembly Hardware (screws, washers, Allen wrench)
- Instruction Manual
Assembly Instructions
Assembly is required for these bar stools. Please follow the steps below carefully. It is recommended to have two people for easier assembly.
Figure 1: Bar Stool Dimensions Overview. This image illustrates the key measurements of the stool, including its overall height of 37.8 inches, seat height of 22.4 inches, and seat dimensions of 16.14 x 16.14 inches.
- Unpack Components: Carefully remove all parts from the packaging. Lay them out on a soft, clean surface to avoid damage. Identify each component using the parts list.
- Attach Backrest to Seat: Align the backrest (X-design) with the pre-drilled holes on the back edge of the seat. Secure it using the provided screws and Allen wrench. Do not fully tighten yet.
- Assemble Leg Frames: Connect the front and rear leg frames. Ensure the footrest attachment points are facing inward. Secure with screws, leaving them slightly loose for adjustment.
- Attach Seat to Leg Frames: Carefully place the assembled seat and backrest onto the leg frames. Align the holes on the underside of the seat with the top of the leg frames. Insert and hand-tighten the screws.
- Install Footrest Bars: Attach the footrest bars between the leg frames. Ensure they are level and secure them with the remaining screws.
- Final Tightening: Once all components are loosely assembled, place the stool on a flat surface. Apply gentle pressure to ensure it is level, then systematically tighten all screws firmly. Do not overtighten.
Figure 2: Key Features. This image highlights the ergonomic backrest, high-density sponge padding in the seat, the sturdy metal footrest, and the overall solid metal frame construction.
Operating Instructions
These bar stools are designed for comfortable seating at counter height surfaces, such as kitchen islands or home bars. To ensure safe and proper use:
- Always sit centrally on the seat to distribute weight evenly.
- Use the footrest for added comfort and stability.
- Avoid sudden movements or leaning excessively to one side to prevent tipping.
- Do not use the stool as a step ladder or for climbing.
Figure 3: Stools in a Kitchen Island Setting. This image shows two bar stools comfortably placed at a kitchen island, illustrating their intended use.
Figure 4: Stools in a Dining Room Setting. This image displays four bar stools around a dining table, highlighting their versatility for various dining spaces.
Maintenance
Regular maintenance will help prolong the life and appearance of your GAOMON bar stools.
- Cleaning: The PU leather seat is waterproof and easy to clean. Wipe spills immediately with a damp cloth. For general cleaning, use a mild soap solution and a soft cloth, then dry thoroughly. Avoid harsh chemicals or abrasive cleaners.
- Frame Care: The metal frame can be wiped clean with a damp cloth. Avoid prolonged exposure to moisture to prevent rust.
- Fasteners: Periodically check all screws and bolts to ensure they are tight. Retighten as necessary to maintain stability and prevent wobbling.
- Placement: Avoid placing the stools in direct sunlight or near heat sources, as this can cause the material to fade or degrade over time.
Figure 5: Wide and Cozy Seat Detail. This image provides a close-up of the PU upholstered seat, highlighting its texture and comfortable padding.
Troubleshooting
If you encounter any issues with your bar stools, refer to the following common solutions:
- Wobbling Stool: Ensure all screws are tightened evenly. If the floor is uneven, consider using furniture pads under the legs to stabilize.
- Loose Parts: Regularly check and tighten all fasteners. If a screw repeatedly loosens, apply a small amount of thread locker (not included) before re-tightening.
- Scratches on Floor: Ensure the plastic feet caps are intact. Replace if damaged to protect your flooring.
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 16.14"D x 16.14"W x 37.8"H |
| Color | Black |
| Brand | GAOMON |
| Size (Seat Height) | 22.4"H |
| Style | Modern |
| Frame Material | Metal |
| Seat Material Type | PU Leather (Upholstered) |
| Maximum Weight Recommendation | 250 Pounds |
| Assembly Required | Yes |
| Number of Pieces | 2 |
| Item Weight (per stool) | Approx. 11.5 pounds (23 pounds for 2) |
| Model Number | FYY-LH231213001 |
| UPC | 820559716104 |
Warranty and Support
GAOMON products are manufactured with quality and care. For any questions regarding assembly, missing parts, or product performance, please contact GAOMON customer support. Please have your model number (FYY-LH231213001) and purchase information ready when contacting support.
Specific warranty details may vary by region and retailer. Please refer to your purchase documentation for warranty terms and conditions.