Introduction
Thank you for choosing DUMOS 26-inch counter height bar stools. This manual provides essential information for the safe assembly, operation, maintenance, and troubleshooting of your new bar stools. Please read these instructions carefully before assembly and retain for future reference.
Image: DUMOS 26-inch counter height bar stools in a modern kitchen setting, showcasing their design and fit.
Safety Information
- Avoid placing heavy objects on the stools that exceed the recommended weight limit of 330 pounds.
- Keep the stools on stable, non-slippery surfaces to prevent accidents.
- Ensure all screws and bolts are securely tightened before use and periodically check for looseness.
- Do not stand on the stools.
- Keep small parts away from children during assembly to prevent choking hazards.
Package Contents
Before beginning assembly, ensure all parts are present and undamaged. If any parts are missing or damaged, please contact DUMOS customer support.
- Bar Stool Seats (4 units)
- Metal Leg Frames (4 units)
- Assembly Hardware (screws, washers, Allen wrench)
- Instruction Manual (this document)
Setup and Assembly Instructions
Assembly is straightforward and typically takes 10-15 minutes per stool. It is recommended to assemble on a soft, clean surface to prevent scratching the product or floor.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a protected surface. Verify all components listed in the 'Package Contents' section are present.
- Attach Seat to Frame: Align the pre-drilled holes on the underside of the bar stool seat with the holes on the top of the metal leg frame. Insert the provided screws and washers.
- Secure Screws: Using the included Allen wrench, hand-tighten all screws initially. Do not fully tighten until all screws are in place.
- Final Tightening: Once all screws are in place, fully tighten them to ensure stability. Be careful not to overtighten.
- Check Stability: Gently shake the assembled stool to ensure it is stable and all connections are secure. Adjust if necessary.
For a visual guide, DUMOS also provides online video guides for assembly. Please refer to the product page or DUMOS website for access.
Image: Assembly diagram illustrating the components and initial setup steps.
Image: Detailed assembly diagram for attaching the seat to the metal frame.
Operating Instructions
- Ensure the stool is placed on a flat, stable surface before sitting.
- Sit centrally on the seat to distribute weight evenly.
- Utilize the integrated footrest for comfort and to reduce body pressure during extended sitting.
- Do not drag the stools across the floor; lift them when moving to prevent damage to the floor and the stool's non-slip protectors.
Image: Visual representation of the stool's ergonomic design, durable frame, footrest, and non-slip floor protectors.
Maintenance and Care
- Cleaning: The faux leather upholstery is waterproof and resistant to spills and stains. For cleaning, simply wipe with a damp cloth. Avoid using harsh chemicals or abrasive cleaners.
- Frame Care: The black powder-coated metal frame can be wiped clean with a soft, damp cloth.
- Regular Checks: Periodically inspect all screws and connections to ensure they remain tight. Retighten if necessary.
- Avoid Direct Sunlight: Prolonged exposure to direct sunlight may cause the faux leather to fade or crack over time.
Image: Close-up showing the detailed stitching and the waterproof nature of the faux leather, ideal for easy cleaning.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Stool wobbles after assembly | Screws not evenly tightened; uneven floor surface. | Loosen all screws slightly, sit on the stool to settle the frame, then retighten all screws firmly. Ensure the stool is on a flat surface. |
| Difficulty sliding stools on certain floors | Friction between non-slip protectors and floor material. | Lift the stool when moving it. Consider adding felt furniture pads to the bottom of the non-slip protectors for easier sliding on sensitive floors. |
| Squeaking noises | Loose connections or friction between metal parts. | Check and retighten all assembly screws. If noise persists, apply a small amount of silicone lubricant to the joints. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | HJ3SE-6013-BN4new |
| Product Dimensions (D x W x H) | 20.87"D x 18.7"W x 36.23"H |
| Seat Height | 25.9 inches |
| Seat Width | 18.5 inches |
| Color | Warm Brown |
| Frame Material | Metal |
| Seat Material Type | Faux Leather |
| Item Weight (per stool) | Approximately 13.4 pounds |
| Maximum Weight Recommendation | 330 pounds |
| Number of Pieces | 4 |
Image: Diagram illustrating the precise dimensions of the 26-inch counter height bar stool.
Warranty Information
DUMOS products are manufactured with quality and durability in mind. While specific warranty details may vary, DUMOS typically offers a limited warranty against manufacturing defects. Please retain your proof of purchase. For detailed warranty terms and conditions, or to make a warranty claim, please visit the official DUMOS website or contact customer support.
Support
If you have any questions, require assistance with assembly, or encounter any issues not covered in this manual, please do not hesitate to contact DUMOS customer support. Our team is dedicated to providing prompt and helpful service.
- Online Support: Visit the official DUMOS website for FAQs, product registration, and contact forms.
- Email Support: Refer to your purchase documentation for the customer service email address.
- Phone Support: Check the DUMOS website for available phone support numbers and operating hours.
We value your feedback and are committed to ensuring your satisfaction with DUMOS products.