VEVOR OK888-DS730+Top Plate
VEVOR Motorized TV Lift Stand User Manual
Model: OK888-DS730+Top Plate | Brand: VEVOR
Introduction
This manual provides essential instructions for the safe and efficient installation, operation, and maintenance of your VEVOR Motorized TV Lift Stand. Please read this manual thoroughly before assembly and use, and retain it for future reference. This motorized TV lift stand is designed to discreetly store your television within a cabinet or furniture, providing a clean aesthetic when not in use and an optimal viewing experience when deployed.
Figure 1: VEVOR Motorized TV Lift Stand in a living room setting.
Setup and Installation
Package Contents
Verify that all components listed below are present before beginning installation:
- 1 x Motorized TV Stand
- 1 x Digital Wired Manual Controller
- 1 x Wireless Remote Control
- 1 x 29V 1.8A Switching Power Supply
- 1 x Control Receiver Box
- 1 x Power Cord (EU standard, may vary by region)
- 2 x Fixed Iron Plates
- 1 x Top Plate
- 2 x Vertical Rods
- 1 x TV Mounting Bracket
- 1 x Screw Pack (various sizes for TV mounting)
Figure 2: Included components.
Installation Steps
Follow these general steps for installation. Refer to the detailed diagrams for specific assembly instructions.
- Unpack and Inspect: Carefully remove all components from the packaging. Inspect for any damage during transit.
- Assemble the Lift Mechanism: Attach the vertical rods and top plate to the main lift column according to the provided diagrams. Ensure all connections are secure.
- Prepare TV for Mounting: Attach the TV mounting bracket to the back of your television using the appropriate screws from the screw pack. Ensure VESA compatibility (75x75mm to 600x400mm).
- Mount TV to Stand: Carefully lift the television and hook the TV mounting bracket onto the vertical rods of the lift stand. Secure it with the provided fasteners.
- Install in Cabinet/Enclosure: Position the assembled TV lift stand within your chosen cabinet or enclosure. Secure the stand to the base of the furniture using the fixed iron plates and appropriate screws to ensure stability. This stand is designed for floor mounting within furniture, not for ceiling or wall installation.
- Connect Electronics: Connect the power supply, control receiver box, wired controller, and power cord as shown in the wiring diagram. Plug the power cord into a suitable electrical outlet.
- Initial Test: Before final placement, perform an initial test using the remote control to ensure the lift mechanism operates smoothly through its full range of motion.
Figure 3: VESA compatibility and weight capacity.
Operation
Using the Remote Controls
The VEVOR Motorized TV Lift Stand can be operated using either the wireless remote control or the wired manual controller.
- Wireless Remote Control: Point the remote towards the control receiver box. Use the UP and DOWN buttons to raise or lower the television. The STOP button halts movement at any desired height.
- Wired Manual Controller: This controller provides direct access to the lift functions. It typically includes UP, DOWN, and STOP buttons, and may feature additional buttons for memory functions.
Figure 4: Operating the TV lift with remote controls.
Memory Function
The stand features a memory function allowing you to save up to 4 preferred viewing heights. Consult the specific instructions provided with your wired controller for programming these memory positions. Typically, this involves moving the TV to the desired height, pressing a 'Set' or 'M' button, and then pressing a numbered memory button (1-4).
Figure 5: Adjustable height range and memory function.
Maintenance
To ensure the longevity and optimal performance of your VEVOR Motorized TV Lift Stand, follow these maintenance guidelines:
- Cleaning: Wipe the stand and its components with a soft, dry cloth. Avoid abrasive cleaners or solvents that could damage the finish.
- Check Connections: Periodically inspect all electrical connections and mounting hardware to ensure they remain secure. Tighten any loose screws.
- Lubrication: The internal moving parts are generally pre-lubricated and designed for maintenance-free operation. Do not attempt to lubricate unless specifically instructed by VEVOR support.
- Avoid Overloading: Do not exceed the maximum load capacity of 54 kg (120 lbs).
Troubleshooting
If you encounter issues with your TV lift stand, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Stand does not move. | No power; Loose connection; Remote battery low; Overload protection activated. | Check power cord connection and outlet. Ensure all cables are securely connected. Replace remote batteries. Reduce TV weight if exceeding capacity. Allow motor to cool if overheated. |
| Remote control not responding. | Low battery; Obstruction; Remote not paired (if applicable). | Replace remote batteries. Ensure clear line of sight to receiver. Refer to pairing instructions if remote requires pairing. |
| Movement is jerky or noisy. | Loose mounting screws; Obstruction in lift path; Overload. | Check and tighten all mounting screws. Clear any obstructions. Ensure TV weight is within limits. |
If the problem persists after attempting these solutions, please contact VEVOR customer support.
Specifications
| Feature | Specification |
|---|---|
| Model Number | OK888-DS730+Top Plate |
| Type | Lift-up Type |
| Main Material | Alloy Steel |
| Rated Power | 80 W |
| Max Load Capacity | 120 lbs / 54 kg |
| Max VESA Mount Compatibility | 24 x 16 inches / 600 x 400 mm |
| Compatible Screen Size | 32 - 70 inches |
| Travel Range | 39 inches / 990 mm |
| Memory Function | Yes, 4 levels (user adjustable) |
| Product Dimensions (L x W x H) | 28.5 x 6.9 x (29.7 - 80.3) inches / 725 x 175 x (755 - 2040) mm |
| Power Cord Length | 6.6 ft / 2 m |
| Net Weight | 33.6 lbs / 15.22 kg |
Figure 6: Detailed product dimensions and components.
Warranty and Support
Warranty Information
The product data indicates "Warranty Description: Not applicable." For specific warranty terms and conditions, please refer to the purchase documentation or contact your retailer directly.
Customer Support
For technical assistance, replacement parts, or any questions not covered in this manual, please contact VEVOR customer support through their official website or the retailer from whom you purchased the product. Please have your model number (OK888-DS730+Top Plate) and purchase information ready when contacting support.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.