1. Introduction
This manual provides instructions for the installation, operation, and maintenance of the LDGSUPH compatible clear water tank designed for the Liectroux i7Pro Cordless Dry Wet Floor Cleaner. Please read this manual thoroughly before use to ensure proper function and longevity of the product.
2. Safety Information
- Always ensure the vacuum cleaner is powered off and unplugged before installing or removing the water tank.
- Do not overfill the water tank.
- Use only clean water or recommended cleaning solutions for your Liectroux i7Pro device.
- Keep the water tank out of reach of children.
- Inspect the water tank for any damage before each use. Do not use if damaged.
3. Product Overview
The LDGSUPH compatible water tank is designed as a replacement or spare part for the Liectroux i7Pro cordless dry wet floor cleaner. It features a sealed, leak-proof design and precise water control for efficient cleaning.
Image: The clear water tank, showing its transparent body and connection points. This tank is designed to hold water or cleaning solution for the Liectroux i7Pro vacuum cleaner.
Key Features:
- Sealed Leak-Proof Design: Features a built-in high-elastic silicone sealing ring that tightly fits the vacuum cleaner interface, preventing water leakage during movement and cleaning.
- Precise Water Control Structure: Equipped with a miniature water control valve that automatically adjusts water output based on the vacuum cleaner's cleaning mode.
- Accurate Model Adaptation: Manufactured with 1:1 molding to match the original Liectroux i7Pro model, ensuring stable installation.
- Low-Noise Water Output: Optimized water channel structure reduces impact noise during water flow.
4. Setup and Installation
- Prepare the Vacuum Cleaner: Ensure your Liectroux i7Pro cordless dry wet floor cleaner is turned off and unplugged from its charging base.
- Remove Existing Tank (if applicable): If replacing an old water tank, carefully detach it from the vacuum cleaner according to your Liectroux i7Pro's user manual.
- Install the New Water Tank: Align the LDGSUPH compatible water tank with the designated slot on your Liectroux i7Pro. Gently push until it clicks securely into place. The accurate model adaptation ensures a stable fit.
- Verify Connection: Confirm that the tank is firmly seated and the silicone sealing ring is properly engaged to prevent leaks.
5. Operating Instructions
- Fill the Water Tank: Open the water tank cap. Fill the tank with clean water or a suitable cleaning solution, ensuring not to exceed the maximum fill line. Close the cap securely.
- Attach to Vacuum Cleaner: If not already attached, install the filled water tank onto the Liectroux i7Pro as described in the "Setup and Installation" section.
- Begin Cleaning: Operate your Liectroux i7Pro as usual. The precise water control structure will automatically manage water output according to the cleaning mode selected on your vacuum cleaner. The low-noise water output design minimizes disturbance during operation.
- Monitor Water Level: Periodically check the water level during extended cleaning sessions.
6. Maintenance
Regular maintenance ensures optimal performance and extends the lifespan of your water tank.
- Empty After Each Use: After each cleaning session, remove the water tank and empty any remaining water or cleaning solution.
- Clean the Tank: The tank features an easy-to-disassemble and clean design. Separate the tank body and accessories. Rinse all parts thoroughly with clean water. Use a soft brush if necessary to remove any residue. The smooth inner walls facilitate quick cleaning of limescale and residual cleaning solution.
- Dry Thoroughly: Allow all components to air dry completely before reassembling or storing to prevent mold or mildew growth.
- Inspect Seals: Periodically check the silicone sealing ring for wear or damage. Replace if necessary to maintain the leak-proof seal.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Water leakage from tank | Tank not properly installed; Damaged silicone seal; Overfilled tank. | Ensure tank is securely clicked into place; Inspect and replace seal if damaged; Do not overfill past max line. |
| No water dispensed | Tank empty; Water valve clogged; Incorrect cleaning mode selected on vacuum. | Refill tank; Clean water valve (refer to maintenance); Check vacuum cleaner settings. |
| Water flow too low/high | Water valve partially clogged; Vacuum cleaner mode issue. | Clean water valve; Refer to your Liectroux i7Pro manual for water flow settings. |
If issues persist, please refer to the original Liectroux i7Pro manual or contact customer support for your vacuum cleaner.
8. Specifications
- Compatibility: Liectroux i7Pro Cordless Dry Wet Floor Cleaner
- Material: Durable plastic with silicone sealing ring
- Item Weight: 1.76 ounces (approximately 50 grams)
- Package Dimensions: 0.39 x 0.39 x 0.39 inches (1 x 1 x 1 cm) (Note: These dimensions appear to be placeholder or incorrect for a water tank.)
- Manufacturer's Model Number: LIMINGZHI12
9. Warranty and Support
Specific warranty information for this compatible water tank is not provided in the product details. For warranty claims or technical support, please refer to the retailer or manufacturer of the LDGSUPH brand. For issues related to the Liectroux i7Pro vacuum cleaner itself, please consult the Liectroux manufacturer's support channels.