1. Introduction
The Proscenic F10 Ultra+ is a versatile cordless wet and dry vacuum cleaner designed for efficient floor cleaning. It combines vacuuming, mopping, and self-cleaning functions to simplify your cleaning routine. This manual provides essential information for the safe and effective use, maintenance, and troubleshooting of your device.
Image: The Proscenic F10 Ultra+ in use, demonstrating its wet cleaning capability on a hard floor.
2. Product Components
Familiarize yourself with the main components of your Proscenic F10 Ultra+.
- Main Unit (with dirty water tank and motor)
- Handle Assembly
- Clean Water Tank
- Roller Brush
- Charging Base
- Cleaning Solution
- Cleaning Brush
- HEPA Filter (pre-installed)
Image: Front view of the Proscenic F10 Ultra+ vacuum cleaner.
Image: Side view of the Proscenic F10 Ultra+ vacuum cleaner.
Image: Back view of the Proscenic F10 Ultra+ vacuum cleaner.
3. Setup and Assembly
3.1 Unpacking and Initial Assembly
Carefully remove all components from the packaging. Ensure all parts listed in Section 2 are present.
3.2 Handle Assembly
- Insert the handle assembly into the main unit until it clicks securely into place.
3.3 Charging Base Setup
- Place the accessory holder and roller brush holder onto the charging base.
- Connect the power adapter to the charging base and plug it into a power outlet.
3.4 Filling the Clean Water Tank
- Press the clean water tank release button and remove the tank from the main unit.
- Open the tank cap and fill with clean water. You may add a small amount of the provided cleaning solution. Do not exceed the MAX fill line.
- Close the cap securely and reinsert the tank into the main unit until it clicks.
Image: The F10 Ultra+ features high-capacity dual tanks: a 750ml clean water tank and a 550ml dirty water tank, ensuring continuous cleaning with fresh water.
3.5 Initial Charging
Place the assembled vacuum cleaner on the charging base. The LED display will indicate charging status. Fully charge the device before first use (approximately 3 hours).
Video: This video demonstrates the assembly of the Proscenic F10 Ultra+, including attaching the handle, installing the roller brush, setting up the charging base, and inserting the water tanks. It also shows the initial charging process.
4. Operating Instructions
4.1 Power On/Off
Press the power button on the handle to turn the device on or off.
4.2 Cleaning Modes
The F10 Ultra+ offers three cleaning modes:
- Smart Mode: For general daily cleaning, automatically adjusts suction and water flow.
- Max Mode: For stubborn stains and heavy dirt, provides maximum power.
- Suction Mode: For vacuuming liquids only, without dispensing water.
Switch between modes using the dedicated button on the handle. The current mode is displayed on the LED screen.
Image: Three modes adapted to all your cleaning needs: Suction mode for liquids, Max mode for stubborn stains, and Smart mode for daily cleaning.
4.3 LED Display and Voice Prompts
The integrated LED display shows battery life, current cleaning mode, and maintenance alerts. Voice prompts provide real-time information and guidance during operation. You can change the voice prompt language or disable it by pressing and holding the 'Clean' button for 5 seconds, then turning off the device.
Image: Multilingual Voice: Easily switch between languages. Instructions for changing language and activating/deactivating voice prompts are provided.
4.4 Self-Propelled Movement
The F10 Ultra+ features a self-propelled design, making it easy to maneuver and reducing effort during cleaning.
Image: Automatic Cleaning, Effortless for Your Arms. The self-propelled design significantly reduces pressure on your arms.
4.5 Edge and Corner Cleaning
The narrow-sided rotating brush allows for thorough cleaning close to baseboards, in corners, and other hard-to-reach areas.
Image: Edge-to-Edge Cleaning. The F10 Ultra+ effectively cleans near baseboards, in corners, and all difficult-to-access areas.
5. Maintenance
5.1 Automatic Self-Cleaning
After each use, place the vacuum cleaner on its charging base and press the self-clean button. The device will automatically clean the roller brush and internal air ducts, ensuring it remains hygienic and odor-free.
Image: Self-Cleaning: Effortless Cleanliness. A single press of the button activates the self-cleaning of the rotating brush and internal tube.
5.2 Emptying the Dirty Water Tank
When the dirty water tank is full, the device will alert you. Remove the tank, open it, and dispose of the collected dirty water and solid debris. Rinse the tank thoroughly with clean water.
Image: A user emptying the dirty water tank into a toilet, illustrating the ease of disposal.
5.3 Cleaning the Roller Brush
Even with self-cleaning, periodic manual cleaning of the roller brush is recommended. Remove the roller brush cover, then remove the roller brush. Use the provided cleaning brush to remove any tangled hair or debris. Rinse the roller brush under running water and allow it to air dry completely before reinstallation.
5.4 Cleaning the Filter
The HEPA filter should be cleaned regularly to maintain optimal suction performance. Remove the dirty water tank, then remove the filter assembly. Tap the filter to dislodge dry debris and rinse it under running water. Ensure the filter is completely dry before reinserting it.
5.5 Cleaning Solution
Use the provided cleaning solution or a suitable floor cleaning agent in the clean water tank. Always follow the dilution instructions on the cleaning solution bottle.
Image: The Proscenic cleaning solution bottle, designed for use with the F10 Ultra+.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not power on | Low battery; Power button not pressed correctly | Charge the device; Ensure power button is fully pressed |
| Poor suction performance | Dirty water tank full; Filter clogged; Roller brush tangled | Empty dirty water tank; Clean or replace filter; Clean roller brush |
| Water leakage | Water tanks not installed correctly; Tank caps loose | Reinstall water tanks securely; Ensure tank caps are tightly closed |
| Device stops unexpectedly | Overheating; Dirty water tank full; Obstruction | Allow device to cool down; Empty dirty water tank; Check for and remove obstructions |
| Voice prompts not working | Voice prompts disabled | Refer to Section 4.3 to enable voice prompts |
7. Specifications
| Feature | Detail |
|---|---|
| Brand | Proscenic |
| Model Name | F10 Ultra+ |
| Power | 350 Watts |
| Voltage | 28.8 Volts |
| Battery Life | Up to 60 minutes |
| Charging Time | 3 hours |
| Clean Water Tank Capacity | 750 ml |
| Dirty Water Tank Capacity | 550 ml |
| Noise Level | 60 Decibels |
| Filter Type | HEPA Filter |
| Dimensions (L x W x H) | 33L x 27.9W x 114H cm |
| Recommended Surfaces | All hard floors (tiles, parquet, marble, linoleum) |
8. Warranty and Support
8.1 Manufacturer's Warranty
The Proscenic F10 Ultra+ comes with a 2-year manufacturer's warranty. Please retain your proof of purchase for warranty claims.
8.2 Customer Support
For any questions, technical assistance, or warranty inquiries, please contact Proscenic customer support through their official website or the retailer where you purchased the product. Refer to the contact information provided in your product packaging or on the official Proscenic website.
