Introduction
Thank you for choosing the IKT Self Cleaning Bottom Load Water Cooler Dispenser with Nugget Ice Maker. This appliance provides convenient access to hot, cold, and room-temperature water, along with chewable nugget ice. Please read this manual thoroughly before operation to ensure safe and efficient use.
Image: Front view of the IKT Self Cleaning Bottom Load Water Cooler Dispenser.
Safety Information
- Always plug the dispenser into a grounded electrical outlet.
- Do not operate the dispenser with a damaged power cord or plug.
- Keep the dispenser away from direct sunlight and heat sources.
- Ensure proper ventilation around the unit.
- Hot Water Safety: The hot water dispenser features a child safety lock. Always engage the child safety lock when not in use, especially in households with children.
- Do not immerse the dispenser, cord, or plug in water or other liquids.
- Unplug the dispenser before cleaning or performing any maintenance.
- This appliance is for indoor use only.
Setup
- Unpacking: Carefully remove the dispenser from its packaging. Retain packaging for future transport if needed.
- Placement: Place the dispenser on a flat, stable surface. Ensure there is adequate space around the unit for ventilation (at least 4 inches from walls).
- Water Bottle Installation (Bottom Load):
- Open the lower cabinet door.
- Insert the probe into a standard 3-5 gallon water bottle. The tubing that goes into the water jug is stainless steel.
- Slide the water bottle into the cabinet.
- Close the cabinet door.
- Initial Priming: Before plugging in, ensure the water bottle is correctly installed. Allow several minutes for the internal tanks to fill with water. Dispense a small amount of water from each tap (hot, cold, room temperature) to ensure air is purged from the lines.
- Power Connection: Plug the dispenser into a grounded electrical outlet.
Image: Side view of the water cooler dispenser showing a 5-gallon water bottle loaded in the bottom compartment.
Operating Instructions
3 Temperature Settings
The dispenser offers three temperature options: crisp cold, room-temperature, and piping hot water. The control panel features indicator lights for each function.
- Cold Water: Press the "Cold Water" button. The cold water function is ready when its indicator light stays on.
- Room Temperature Water: This is fresh water directly from the bottle, dispensed at ambient temperature.
- Hot Water: Press the "Hot Water" button. The hot water function is ready when its indicator light stays on.
Image: The IKT water cooler dispenser highlighting its 3-in-1 functionality for hot, cold, and room temperature water, plus ice cubes.
Built-in Nugget Ice Maker
This dispenser includes a built-in nugget ice maker. It produces soft, chewable nugget ice and stores it in an internal container for instant dispensing.
- Ice Production: The unit can produce up to 33 lbs of ice daily.
- Ice Storage: The internal storage container holds up to 2.76 lbs of ice.
- Important Note: The machine does not keep ice frozen. Ice will melt over time if not used.
- Ice Bin Full Alert: The machine will emit three beeps and stop making ice when the ice bin is full.
- Dispensing Ice: Press the "Ice" button to dispense nugget ice.
Image: Graphic illustrating the daily ice production capacity (33 lbs) and ice bin storage (2.76 lbs) for the IKT water cooler dispenser. It also notes that the unit does not keep ice frozen.
Child Safety Lock
To prevent accidental dispensing of hot water, the hot water tap is equipped with a child safety lock.
- To dispense hot water, you must first press and hold the "Child Lock" button, then press the "Hot Water" button.
Image: Close-up of the control panel on the IKT water cooler dispenser, showing the "Child Lock" button and other indicators.
Empty Bottle Alert
The dispenser is equipped with an empty bottle indicator to notify you when the water bottle needs replacement.
- The empty bottle indicator is controlled by the PCB program for accurate water level detection.
- When the bottle is empty, the indicator will not light up immediately. It depends on the cold water tank's water level.
- If the bottle is empty, please wait approximately 7 minutes and then check if the "Empty Indicator" light is on.
Self-Cleaning Function
The dispenser features a self-cleaning function to maintain hygiene.
- Hold the power button to turn off the machine.
- Press and hold the ice-making button for 3 seconds to activate the self-cleaning function.
- The indicator light will blink, and the power light will remain on during the cleaning cycle.
- The machine will shut off automatically after approximately 10 minutes when the self-cleaning cycle is complete.
Image: The IKT water cooler dispenser with an overlay explaining the self-cleaning function and its activation steps.
Video: IKT Nugget Ice Maker and Water Cooler Operation
Video: This video demonstrates the operation of the IKT Nugget Ice Maker and Water Cooler, including dispensing water and ice.
Maintenance
- Drip Tray: The removable drip tray should be cleaned regularly to prevent water overflow and maintain hygiene. Simply slide it out, empty, wash with mild soap and water, and replace.
- Exterior Cleaning: Wipe the exterior of the dispenser with a soft, damp cloth. Do not use abrasive cleaners or solvents.
- Self-Cleaning Function: Utilize the built-in self-cleaning function periodically as described in the Operating Instructions.
- Water Bottle Replacement: Replace empty water bottles promptly to ensure continuous operation and prevent the "Empty Bottle Alert" from persisting.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cord unplugged, circuit breaker tripped. | Ensure the power cord is securely plugged in. Check the circuit breaker. |
| No cold water | Cold water function not activated, water tank not cooled, empty water bottle. | Press the cold water button. Allow 15-30 minutes for cooling. Replace the water bottle. |
| No hot water | Hot water function not activated, water tank not heated, empty water bottle. | Press the hot water button. Allow 15-30 minutes for heating. Replace the water bottle. |
| No ice production | Ice maker not activated, water bottle empty, ice bin full. | Ensure the ice maker is on. Replace the water bottle. Empty the ice bin. |
| "Lack of Water" indicator on | Water bottle is empty or not properly installed. | Replace the water bottle and ensure it is correctly seated. Wait 7 minutes for the indicator to update. |
Specifications
- Brand: IKT
- Model Number: IKTLYCZ629N
- Color: Black
- Product Dimensions (D x W x H): 16.5"D x 12.2"W x 40.7"H
- Power Source: Corded Electric
- Ice Production Capacity: Up to 33 lbs per day
- Ice Storage Capacity: Up to 2.76 lbs
- Water Bottle Compatibility: Standard 3-5 Gallon Bottles
- Tank Material: Stainless Steel Weld Tank
Warranty and Support
For warranty information or technical support, please refer to the documentation included with your purchase or contact IKT customer service directly. Contact details can typically be found on the manufacturer's website or on the product packaging.