1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your LoraTap Wireless Switch Kit. This kit allows for convenient remote ON/OFF control of lighting fixtures using an 868 MHz radio frequency transmitter and a 2500W receiver. Please read this manual thoroughly before use to ensure proper function and safety.
2. Safety Information
WARNING: Electrical installation should only be performed by a qualified electrician. Disconnect power at the circuit breaker before installation or servicing. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Ensure the power supply is OFF before connecting the receiver.
- Do not exceed the maximum load capacity of 2500W for the receiver.
- Keep the device away from water and high humidity environments.
- Do not attempt to repair or modify the device yourself. Contact customer support for assistance.
3. Package Contents
Verify that all components are present in the package:
- 1x LoraTap Wireless Receiver (2500W)
- 1x LoraTap Wireless Transmitter (868 MHz, Wall-Mounted)
- Mounting Accessories (screws, adhesive tape)
- User Manual
4. Product Overview
The LoraTap Wireless Switch Kit consists of two main components: a receiver that connects to your lighting fixture and a wireless transmitter that acts as a wall switch.
Figure 1: LoraTap Wireless Switch Kit showing the compact receiver and the sleek wall-mounted transmitter. The receiver is designed for discreet installation, while the transmitter offers flexible placement without wiring.
Receiver (2500W)
- Connects directly to the electrical circuit of your light fixture.
- Receives wireless signals from the transmitter to turn the light ON/OFF.
- Maximum load: 2500W.
Transmitter (868 MHz)
- Battery-powered, no wiring required.
- Sends 868 MHz radio signals to the receiver.
- Can be mounted on any wall surface using screws or adhesive.
5. Setup and Installation
5.1 Receiver Installation
- Turn off Power: Locate the circuit breaker controlling the light fixture and turn off the power supply. Verify power is off using a voltage tester.
- Connect Receiver: Open the junction box or light fixture housing. Connect the receiver according to the wiring diagram provided (typically Live In, Neutral In, Live Out, Neutral Out). Ensure all connections are secure.
- Secure Receiver: Place the receiver inside the junction box or fixture housing, ensuring it does not obstruct any components or wiring.
- Restore Power: Close the junction box/fixture housing and restore power at the circuit breaker.
5.2 Transmitter Installation
- Choose Location: Select a desired location for your wireless switch. No wiring is needed, offering flexibility.
- Mount Transmitter: You can either use the provided screws to permanently mount the switch plate to the wall or use the adhesive tape for a non-permanent solution. Ensure the surface is clean and dry before applying adhesive.
6. Operating Instructions
6.1 Pairing the Transmitter and Receiver
Before first use, the transmitter and receiver must be paired. Follow these steps:
- Enter Pairing Mode: After restoring power to the receiver, press and hold the pairing button on the receiver for approximately 3-5 seconds until the indicator light starts flashing.
- Activate Transmitter: Within 10 seconds of the receiver's indicator light flashing, press the ON or OFF button on your wireless transmitter.
- Confirmation: The receiver's indicator light will stop flashing and/or the connected light will toggle ON/OFF once to confirm successful pairing.
- Add More Transmitters (Optional): To pair additional transmitters to the same receiver, repeat steps 1-3 for each transmitter.
6.2 Basic Operation
- Turn ON: Press the ON button on the wireless transmitter to turn on the connected light.
- Turn OFF: Press the OFF button on the wireless transmitter to turn off the connected light.
7. Maintenance
- Cleaning: Wipe the transmitter surface with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement (Transmitter): If the transmitter's range decreases or it becomes unresponsive, the battery may need replacement. Refer to the transmitter's specific instructions for battery type and replacement procedure. Typically, this involves opening the back cover and replacing a coin cell battery.
- Receiver: The receiver is maintenance-free once installed. Do not open its casing.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn ON/OFF. | No power to receiver; Transmitter not paired; Transmitter battery low; Receiver faulty. | Check circuit breaker. Re-pair transmitter and receiver. Replace transmitter battery. Contact support. |
| Reduced wireless range. | Obstructions (metal, thick walls); Transmitter battery low. | Relocate transmitter if possible. Replace transmitter battery. |
| Light flickers or behaves erratically. | Overload on receiver; Loose wiring connection. | Ensure total wattage of connected lights does not exceed 2500W. Check wiring connections (power off first). |
9. Specifications
| Brand: | LoraTap |
| Model: | Wireless Switch Kit |
| Receiver Max Load: | 2500W |
| Wireless Frequency: | 868 MHz |
| Operating Voltage: | AC 100-250V (Receiver) |
| Transmitter Battery: | CR2032 (or similar coin cell, check specific model) |
| Operating Temperature: | -10°C to 45°C |
| Wireless Range: | Up to 30m indoors, 100m outdoors (line of sight) |
10. Warranty and Customer Support
LoraTap products come with a standard manufacturer's warranty. Please refer to the warranty card included in your package or visit the official LoraTap website for detailed warranty terms and conditions.
For technical support, troubleshooting assistance, or warranty claims, please contact LoraTap customer service:
- Website: www.loratap.com (Note: This is an example URL. Please refer to actual product documentation for correct contact information.)
- Email: support@loratap.com (Note: This is an example email. Please refer to actual product documentation for correct contact information.)
When contacting support, please have your product model number (Wireless Switch Kit) and purchase date available.
