ACEBEAM E10 2.0 Longest-Range Pocket EDC Flashlight User Manual

1. Introduction

Thank you for choosing the ACEBEAM E10 2.0 Longest-Range Pocket EDC Flashlight. This manual provides essential information for the safe and efficient use of your device. Please read it thoroughly before operation and retain it for future reference.

What's in the Box

• E10 2.0 Flashlight (Battery Included) x 1
• Lanyard x 1
• O-rings x 2
• USB Cable x 1
• User Manual x 1

2. Product Features

• Longest-Range Pocket EDC Flashlight: Compact design (3.47in long, 3.76oz) with a custom TIR optic and CREE XP-LR LED, delivering up to 1,200 lumens and a beam distance of 715 meters.
• Magnetic Base: The magnetic tail cap allows secure attachment to metal surfaces for hands-free operation.
• Rechargeable: Features a USB-C rechargeable 16340 battery (included).
• Durable and Sturdy: Constructed from aerospace-grade AL6061-T6 aluminum with a hard-anodized finish. Rated IP68 for waterproof performance and 1.5-meter impact resistance.
• Easy to Carry: Designed for everyday carry, fitting easily into pockets.
• Intuitive Side Switch: Provides smooth, one-handed control for mode changes.

Image: Overview of the ACEBEAM E10 2.0 flashlight highlighting its key features.

3. Setup

Battery Installation

1. Unscrew the tail cap of the flashlight.
2. Insert the included 16340 rechargeable battery with the positive (+) end facing towards the head of the flashlight.
3. Screw the tail cap back on securely. Ensure the O-ring is properly seated to maintain waterproof integrity.

Note: The E10 2.0 is compatible with CR123A batteries, but the included 16340 battery offers USB-C charging capability.

Charging the Battery

The included 16340 battery features a built-in USB-C charging port. To charge:

1. Unscrew the tail cap and remove the 16340 battery from the flashlight.
2. Locate the USB-C port on the side of the battery.
3. Connect the provided USB-C cable to the battery and a suitable USB power source (e.g., phone charger, laptop).
4. The indicator light on the battery will show charging status (typically red for charging, green for fully charged).
5. Once fully charged, disconnect the cable and reinsert the battery into the flashlight, ensuring the tail cap is tightened.

Image: The ACEBEAM E10 2.0 flashlight demonstrating its convenient USB-C charging capability.

4. Operating Instructions

The ACEBEAM E10 2.0 features an intuitive side switch for easy operation.

Basic Operation

• Turn On/Off: Single press the side switch to turn the flashlight on or off.
• Change Brightness Levels: When the flashlight is on, press and hold the side switch to cycle through Ultra-Low, Low, Medium, and High modes. Release the switch to select the desired brightness.

Special Modes

• Turbo Mode: Double-press the side switch quickly to activate Turbo mode (1200 lumens). Double-press again to return to the previously used mode.
• Strobe Mode: Triple-press the side switch quickly to activate Strobe mode. Triple-press again to return to the previously used mode.

Lockout Function

To prevent accidental activation, the flashlight has a lockout function:

• Activate Lockout: When the flashlight is off, press and hold the side switch for approximately 3 seconds until the light flashes briefly, indicating it is locked.
• Deactivate Lockout: Press and hold the side switch for approximately 3 seconds until the light turns on in Ultra-Low mode, indicating it is unlocked.

Image: Illustration of the intuitive side switch and available lighting modes.

5. Maintenance

Cleaning

• Wipe the flashlight body with a clean, soft cloth.
• Clean the lens with a lens cloth to maintain optimal light output.

Battery Care

• Charge the battery regularly, especially if the flashlight will not be used for an extended period.
• Store the battery in a cool, dry place.

O-Rings

• Periodically inspect the O-rings for wear or damage.
• Replace damaged O-rings with the provided spares to maintain the IP68 waterproof rating.
• Apply a thin layer of silicone grease to the O-rings to ensure a good seal and prevent drying.

6. Troubleshooting

• Flashlight not turning on:
      - Ensure the battery is correctly installed with the positive (+) end facing the head.
      - Check if the battery is charged. Remove and charge the battery using the USB-C port.
      - Verify the flashlight is not in lockout mode. Press and hold the side switch for 3 seconds to unlock.
• Light is dim or flickers:
      - The battery level may be low. Recharge the battery.
      - Ensure the tail cap is fully tightened. A loose connection can cause intermittent power.
• Water ingress after exposure:
      - Check the O-rings for any damage or improper seating. Replace if necessary and ensure they are lubricated.
• Flashlight gets hot during use:
      - High brightness modes (especially Turbo) generate significant heat. This is normal. The flashlight has built-in thermal regulation to prevent overheating by automatically reducing output.

If you experience issues not covered here, please contact ACEBEAM customer support.

7. Specifications

Image: Detailed technical specifications table for the E10 2.0 flashlight.

8. Warranty and Support

Warranty Information

The ACEBEAM E10 2.0 flashlight comes with a 10-year manufacturer's warranty, ensuring long-term reliability and peace of mind.

Customer Support

For any questions, technical assistance, or warranty claims, please contact ACEBEAM customer support or visit the official ACEBEAM store online.

Official ACEBEAM Store: Visit Store