Donner HHCB-12 Electronic Drum Hi-Hat Pad with Stand User Manual

Introduction

Thank you for purchasing the Donner HHCB-12 Electronic Drum Hi-Hat Pad with Stand. This product is designed to enhance your electronic drumming experience by providing a realistic hi-hat feel with a dedicated stand. This manual provides essential information for the proper setup, operation, and maintenance of your new hi-hat pad and stand. Please read this manual thoroughly before use to ensure optimal performance and longevity of the product.

Important Safety Information

Always place the hi-hat stand on a stable, level surface to prevent tipping.
Ensure all screws and clamps are securely tightened before playing to prevent components from shifting or falling.
Keep the product away from water, moisture, and extreme temperatures.
Do not attempt to disassemble or modify the product. Refer all servicing to qualified personnel.
Keep small parts out of reach of children to prevent choking hazards.
Use only the power adapter specified for your electronic drum module, if applicable, when connecting the hi-hat pad.

Package Contents

Please check that all the following items are included in your package:

Donner HHCB-12 Electronic Hi-Hat Pad (12-inch)
Hi-Hat Stand
Hi-Hat Clutch
Connection Cable
User Manual (this document)

Setup Instructions

Follow these steps to assemble and set up your Donner HHCB-12 Hi-Hat Pad and Stand:

1. Assemble the Hi-Hat Stand

Unfold the tripod base of the hi-hat stand and ensure it is stable.
Extend the lower tube of the stand to your desired height and secure it with the wing nut.
Insert the upper tube into the lower tube. Do not tighten yet.

Assembled Donner HHCB-12 Hi-Hat Pad and Stand

Image: The Donner HHCB-12 Electronic Hi-Hat Pad mounted on its stand, ready for connection to an electronic drum module. The stand features a sturdy tripod base and a foot pedal.

2. Attach the Hi-Hat Pad

Place the bottom hi-hat pad onto the stand's clutch rod.
Attach the hi-hat clutch to the top hi-hat pad. Ensure the clutch is securely fastened to the pad.
Slide the top hi-hat pad (with clutch) onto the stand's rod, above the bottom pad. Adjust the height and angle for comfortable playing.
Tighten the wing nut on the upper tube to secure the hi-hat pads at the desired height.

Close-up of Donner HHCB-12 Hi-Hat Pad on Stand

Image: A detailed view of the Donner HHCB-12 electronic hi-hat pad, showing its black surface and the chrome stand components. The hi-hat clutch mechanism is visible, securing the pad to the stand rod.

3. Connect to Electronic Drum Module

Locate the hi-hat input on your electronic drum module. This is typically labeled "HH" or "Hi-Hat".
Connect one end of the provided connection cable to the output jack on the hi-hat pad.
Connect the other end of the cable to the hi-hat input on your drum module.
Power on your electronic drum module and select the appropriate hi-hat settings according to your module's manual.

Operating Instructions

The Donner HHCB-12 Hi-Hat Pad is designed to replicate the feel and response of an acoustic hi-hat. Its operation is straightforward once connected to your electronic drum module.

Open Hi-Hat: Strike the pad when the foot pedal is not pressed down.
Closed Hi-Hat: Strike the pad while pressing the foot pedal down completely.
Foot Splash/Chick: Press the foot pedal down quickly without striking the pad to produce a "chick" sound, or release it quickly for a "splash" sound, depending on your module's settings.
Half-Open Hi-Hat: Partially press the foot pedal down and strike the pad. The sensitivity and sound variation for half-open states can usually be adjusted in your drum module's settings.

For detailed sound adjustments and sensitivity calibration, refer to the user manual of your specific electronic drum module.

Maintenance and Care

Cleaning: Wipe the hi-hat pad and stand with a soft, dry cloth. For stubborn dirt, a slightly damp cloth can be used, followed by a dry cloth. Avoid abrasive cleaners or solvents.
Storage: When not in use for extended periods, store the hi-hat pad and stand in a clean, dry environment, away from direct sunlight and extreme temperatures.
Inspections: Periodically check all screws, nuts, and clamps for tightness. Re-tighten as necessary to ensure stability and prevent wear.
Cable Care: Avoid bending or kinking the connection cable excessively. Store it neatly to prevent damage.

Troubleshooting

Problem	Possible Cause	Solution
No sound from hi-hat pad.	Cable not connected properly. Incorrect input on drum module. Module settings incorrect. Damaged cable or pad.	Ensure the connection cable is securely plugged into both the pad and the module. Verify the cable is connected to the designated hi-hat input on your module. Check your drum module's settings to ensure the hi-hat input is enabled and assigned correctly. Try a different cable. If the issue persists, contact customer support.
Hi-hat sound is always open or always closed.	Hi-hat clutch not adjusted correctly. Module settings for hi-hat control are incorrect.	Adjust the hi-hat clutch to allow proper movement and sensor activation. Calibrate the hi-hat pedal in your drum module's settings. Refer to your module's manual.
Pad feels unstable or wobbly.	Stand not fully extended or tightened. Loose components.	Ensure the tripod base is fully spread and all height adjustment wing nuts are securely tightened. Check all clamps and screws on the stand and hi-hat clutch for tightness.

Specifications

Model:	HHCB-12
Type:	Electronic Hi-Hat Pad with Stand
Pad Size:	12 inches
Compatibility:	Compatible with most electronic drum modules (check module specifications for input requirements)
Included Accessories:	Hi-Hat Stand, Hi-Hat Clutch, Connection Cable

Warranty and Support

Donner products are designed for reliability and performance. For information regarding warranty coverage, technical support, or service, please refer to the warranty card included with your product or visit the official Donner website.

Donner Official Website: www.donnerdeal.com

When contacting support, please have your product model (HHCB-12) and purchase date available.

	Donner DE-100 Electronic Drum User Manual Comprehensive user manual for the Donner DE-100 Electronic Drum, covering installation, setup, operation, and safety guidelines. Learn how to assemble the drum kit, connect components, and adjust settings for optimal performance.
	Donner Beat Electronic Drum Kit User Manual Comprehensive user manual for the Donner Beat electronic drum kit, detailing its features, connections, effects, practice modes, recording capabilities, and system settings.
	Donner STARRYPAD User Manual: MIDI Pad Controller Guide Comprehensive user manual for the Donner STARRYPAD MIDI pad controller. Learn about its features, operation, and specifications for music production, including models STARRYPAD MINI and DPD-16.
	Donner Beat Max Electronic Drum User Manual A comprehensive user guide for the Donner Beat Max electronic drum kit, detailing its features, operation, connections, and maintenance for musicians.
	Donner DED-100 Electronic Drum Instruction Manual Comprehensive instruction manual for the Donner DED-100 Electronic Drum, covering setup, operation, features, maintenance, and safety precautions.
	Donner DED-200 Electronic Drum Instruction Manual Comprehensive instruction manual for the Donner DED-200 Electronic Drum, covering installation, operation, features, maintenance, and safety precautions. Includes detailed setup guides and troubleshooting information.

Donner HHCB-12