1. Introduction and Overview
Thank you for choosing Morimoto XB LED Fog Lights. This manual provides essential information for the safe and correct installation, operation, and maintenance of your new fog lights. These lights are designed as a direct replacement for the original halogen units in 2015-2017 Subaru Legacy vehicles, offering enhanced visibility and a modern aesthetic.
The Morimoto XB LED Fog Lights feature a durable polycarbonate lens, a powder-coated cast aluminum housing for efficient heat dissipation, and are compliant with SAE, DOT, and ECE regulations. Each light is equipped with three 5500K LEDs, delivering 2400 lumens for a wide and evenly distributed beam pattern.
Image 1.1: Morimoto XB LED Fog Lights with their product packaging.
2. Safety Information
- Always disconnect the vehicle's battery before beginning any electrical work to prevent electrical shock or damage to the vehicle's electrical system.
- Wear appropriate personal protective equipment, including safety glasses and gloves, during installation.
- Ensure the vehicle is parked on a level surface with the parking brake engaged and the engine off.
- Allow the lights to cool down before handling if they have been recently in operation.
- Avoid looking directly into the LED light source when illuminated, as it can cause eye strain or damage.
- If you are unsure about any part of the installation process, consult a qualified automotive technician.
3. Package Contents
Verify that all components are present and undamaged before proceeding with installation.
- One Pair of Morimoto XB LED Fog Lights
- One Pair of Plug and Play Connectors (may be attached to the fog lights or separate)
Image 3.1: The Morimoto XB LED Fog Lights as they appear in their retail packaging.
4. Setup and Installation
The Morimoto XB LED Fog Lights are designed for a direct, plug-and-play installation, utilizing existing mounting points on your vehicle. No cutting, splicing, or additional wiring is typically required.
4.1 Tools Required (Not Included)
- Basic hand tools (e.g., screwdrivers, wrenches, trim removal tools) as required by your vehicle's specific fog light removal procedure.
- Vehicle service manual (recommended for detailed OEM fog light removal instructions).
4.2 Installation Steps
- Prepare Vehicle: Park the vehicle on a level surface, engage the parking brake, and turn off the engine. Disconnect the negative terminal of the vehicle's battery.
- Access OEM Fog Lights: Depending on your Subaru Legacy model (2015-2017), access to the fog lights may require removing fender liners, bumper covers, or other trim pieces. Refer to your vehicle's service manual for precise instructions on removing the OEM fog light assemblies.
- Remove OEM Fog Lights: Once accessible, carefully unclip the wiring harness from the back of the OEM fog light. Then, unbolt or unclip the OEM fog light assembly from its mounting points.
- Install Morimoto XB LED Fog Lights: Position the new Morimoto XB LED Fog Light into the factory mounting location. Secure it using the original hardware or provided hardware, ensuring it is firmly seated.
- Connect Wiring: Connect the plug-and-play connector from the Morimoto XB LED Fog Light to the vehicle's factory fog light harness. Ensure the connection is secure and sealed.
- Repeat for Other Side: Follow steps 2-5 for the other side of the vehicle.
- Reassemble Vehicle: Reinstall any removed fender liners, bumper covers, or trim pieces.
- Reconnect Battery: Reconnect the negative terminal of the vehicle's battery.
- Test and Aim: Turn on the vehicle's fog lights and verify proper operation. Proceed to Section 5.2 for aiming instructions.
Image 4.1: Rear view of the fog lights, highlighting the integrated height adjusters and plug-and-play connectors.
5. Operating Instructions
5.1 Turning On/Off
The Morimoto XB LED Fog Lights operate in conjunction with your vehicle's factory fog light switch. Refer to your Subaru Legacy owner's manual for specific instructions on how to activate and deactivate the fog lights.
5.2 Aiming the Fog Lights
Proper aiming of fog lights is crucial for optimal performance and to avoid blinding oncoming traffic. The Morimoto XB LED Fog Lights feature integrated height adjusters for precise aiming.
- Preparation: Park your vehicle on a level surface approximately 25 feet (7.6 meters) from a wall or garage door. Ensure tire pressure is correct and the vehicle is unloaded.
- Identify Adjustment Screw: Locate the aiming adjustment screw on the back of each fog light assembly (refer to Image 4.1).
- Adjust Aim: Turn on your vehicle's fog lights. Use a Phillips head screwdriver to turn the adjustment screw. Turning clockwise will typically raise the beam, and counter-clockwise will lower it.
- Target Aim: The top edge of the fog light beam should typically be aimed at or slightly below the center of the fog light housing itself when projected onto the wall. The beam should spread wide and low. Consult local regulations or a professional for precise aiming standards in your region.
- Final Check: After adjustment, take the vehicle for a short drive to confirm proper aiming and ensure visibility is improved without causing glare to other drivers.
6. Maintenance
The Morimoto XB LED Fog Lights are designed for minimal maintenance due to their durable construction and LED technology.
- Cleaning: Periodically clean the polycarbonate lenses with a soft cloth and mild soap and water. Avoid abrasive cleaners or harsh chemicals, as these can damage the lens surface.
- Inspection: Regularly inspect the fog lights for any signs of damage, loose connections, or debris accumulation. Ensure the mounting hardware remains secure.
- No User-Serviceable Parts: The LED components are integrated and not designed for user replacement. Do not attempt to disassemble the fog light housing.
Image 6.1: Close-up view of the durable polycarbonate lens and internal LED array.
7. Troubleshooting
If you encounter issues with your Morimoto XB LED Fog Lights, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fog lights do not turn on | Loose electrical connection Blown fuse Faulty vehicle switch | Check all wiring connections for security. Inspect and replace the vehicle's fog light fuse if necessary (refer to vehicle manual). Test the vehicle's fog light switch. |
| Fog lights flicker | Loose connection Voltage fluctuation | Ensure all connections are tight. Verify stable 12V DC power supply to the fog lights. |
| Improper light aim | Incorrect adjustment | Refer to Section 5.2 for detailed aiming instructions. |
| Moisture inside lens | Seal compromise (rare) | Ensure proper installation and sealing. If persistent, contact Morimoto support. |
If troubleshooting steps do not resolve the issue, please contact Morimoto customer support or your authorized dealer for further assistance.
8. Specifications
| Feature | Specification |
|---|---|
| Brand | Morimoto |
| Model | XB Fog Light (AMZ-ASB-0812) |
| Vehicle Fitment | 2015-2017 Subaru Legacy |
| Light Source Type | LED |
| Color Temperature | 5500K |
| Lumen Output | 2400 Lumens (per pair) |
| Voltage | 12 Volts (DC) |
| Lens Material | Polycarbonate |
| Housing Material | Powder-coated Cast Aluminum |
| Special Features | Dustproof, Waterproof (IP67 rated) |
| Certifications | SAE, DOT, ECE Compliant |
| Item Weight | 2 pounds |
| Package Dimensions | 12 x 8 x 6 inches |
9. Warranty and Support
For information regarding the warranty period and terms for your Morimoto XB LED Fog Lights, please refer to the warranty documentation included with your purchase or visit the official Morimoto website. For technical support, installation assistance, or warranty claims, please contact Morimoto customer service or the authorized retailer from whom you purchased the product.
Morimoto Contact Information: Please refer to your product packaging or the official Morimoto website for the most current contact details.
