1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Blütezeit MS650 Solar Dual-Arm Swing Gate Opener and Exit Wand system. The MS650 is designed for heavy-duty swing gates, offering reliable and convenient automated access with solar power capabilities and an automatic vehicle exit sensor. Please read this manual thoroughly before installation and operation to ensure proper function and safety.
2. Safety Information
WARNING: Failure to follow these safety instructions may result in serious injury or death. Keep children and pets away from the gate area at all times. Do not allow children to operate the gate opener or play with controls. Ensure the gate area is clear before operating. Install safety devices such as photo-eye sensors to prevent entrapment. Disconnect power before performing any maintenance or service.
- Read all instructions carefully before installation and use.
- Ensure the gate is properly installed and in good working condition before installing the opener.
- Do not install the gate opener if the gate is unbalanced or damaged.
- Only qualified personnel should perform electrical connections.
- Keep hands and clothing clear of the gate and opener mechanisms.
- In case of power failure, use the manual release mechanism.
- Regularly inspect the gate opener for signs of wear or damage.
3. Package Contents
Verify that all components listed below are present in your package:
- Dual Gate Opener Arms (2 units)
- Control Box with Integrated 24V Lithium Battery
- 25W Solar Panel with Mounting Bracket
- Remote Transmitters (2 units)
- Exit Wand Vehicle Sensor with 50ft Cable
- Mounting Hardware and Brackets
- Emergency Release Keys
- Instruction Manual (this document)
4. Product Features
4.1. High-Capacity Dual-Arm Solar Gate System
The MS650 supports gates up to 1760 lb and 18 ft, powered by a built-in 24V 6.0Ah lithium battery and high-efficiency 25W solar panel. The strong dual-arm design ensures stability and long-term reliability even on large or heavy gates.
Image: The control box with an integrated 24V 6.0Ah lithium battery, providing a compact and efficient power solution for the gate opener.
Image: A 25W monocrystalline solar panel with an adjustable bracket, designed for efficient solar charging and optimal sunlight exposure.
Image: An internal view of the gate opener arm, highlighting its precision structure and robust components designed for powerful and stable gate movement.
4.2. Hands-Free Automatic Exit with Vehicle Wand
The included Exit Wand detects moving vehicles and triggers the gate to open automatically—no remote needed. It features a heavy-duty 50 ft direct-burial cable, adjustable sensitivity (2–12 ft), and smart auto-calibration for accurate detection.
Image: The durable waterproof housing of the Exit Wand, protecting internal components from rain, dust, and moisture for reliable outdoor performance.
Image: The Range Adjustment Board for the Exit Wand, allowing precise sensitivity tuning for accurate vehicle detection and flexible installation.
Image: The selective vehicle sensor of the Exit Wand, designed to precisely detect cars and motorcycles while filtering pedestrians and animals.
Image: A robust 50ft five-core control cable for the Exit Wand, providing reliable signal transmission and easy connection to the gate opener.
4.3. All-in-One Control Box
No external battery boxes or extra wiring required. The integrated battery design streamlines installation, while Smart Auto-Setting technology automatically calibrates gate angle and travel for smooth operation.
4.4. Manual Release for Emergencies
Each arm includes an integrated clutch system. Insert the key to unlock the motor for manual gate operation during outages or emergency access—no need to remove the arms or disassemble components.
4.5. Durable, Weather-Ready Design
Engineered for outdoor environments with robust materials and consistent performance in harsh conditions.
4.6. Remote Transmitters
Secure 433MHz frequency with rolling code encryption ensures safe, interference-free remote control. Easily pairs new remotes via synced transmission from pre-programmed units—no host reset required.
Image: Two remote transmitters for the gate opener, featuring secure 433MHz rolling code encryption for reliable and interference-free operation.
5. Setup & Installation
This section outlines the general steps for installing your Blütezeit MS650 gate opener system. Refer to the detailed diagrams in the included printed manual for precise measurements and wiring instructions.
5.1. Pre-Installation Checklist
- Ensure your gate is structurally sound and operates smoothly manually.
- Confirm adequate space for the opener arms to extend and retract without obstruction.
- Gather necessary tools: drill, wrenches, measuring tape, level, wire strippers, etc.
- Plan the routing for all cables (power, solar panel, exit wand).
5.2. Mounting the Gate Opener Arms
- Determine the optimal mounting positions on your gate posts and gate frames. This is crucial for proper gate operation and opener longevity.
- Securely attach the front and rear mounting brackets to the gate post and gate frame using appropriate hardware. Ensure they are level and aligned.
- Attach the gate opener arms to the installed brackets. Ensure the arms can move freely through their full range of motion.
- Repeat for the second gate arm.
5.3. Installing the Solar Panel
- Choose a location for the solar panel that receives maximum direct sunlight throughout the day, free from shadows.
- Mount the solar panel bracket securely.
- Attach the 25W solar panel to the bracket. Adjust the tilt angle to optimize sunlight exposure.
- Connect the solar panel cable to the designated solar input terminals on the control board inside the control box.
5.4. Connecting the Exit Wand
- Bury the Exit Wand sensor in the driveway at the desired distance from the gate (typically 10-15 feet) to detect exiting vehicles. Ensure the wand is buried deep enough to be protected and its cable is routed safely.
- Route the 50ft control cable from the Exit Wand to the control box.
- Connect the Exit Wand's wires to the corresponding terminals on the control board as indicated in the wiring diagram.
- Adjust the sensitivity of the Exit Wand using the Range Adjustment Board if necessary, after initial setup.
5.5. Wiring the Control Box
- Connect the motor cables from each gate arm to the appropriate motor terminals on the control board.
- Ensure all connections are secure and properly insulated.
- Close the control box securely to protect internal components from weather.
5.6. Initial Power-Up and Calibration
- Ensure all wiring is correct and secure.
- Power on the system. The integrated battery will provide power.
- Perform the Smart Auto-Setting calibration as per the control board instructions. This process automatically learns the gate's travel limits and angles.
- Test the gate operation using a remote control.
6. Operating Instructions
6.1. Using the Remote Control
- Press the designated button on the remote control once to open or close the gate.
- Pressing the button again during operation will stop the gate. A third press will reverse its direction.
- Ensure you have a clear line of sight to the gate and that the area is clear before operating.
6.2. Automatic Exit Wand Operation
- When a vehicle approaches the Exit Wand from the inside of the property, the sensor will detect its presence.
- The gate will automatically open to allow the vehicle to exit.
- After the vehicle has passed and the gate's auto-close timer expires, the gate will close automatically.
- The Exit Wand is designed to filter out pedestrians and small animals, activating only for vehicles.
6.3. Manual Release Operation
In case of power failure or emergency, the gate can be operated manually:
- Locate the manual release keyhole on each gate opener arm.
- Insert the provided emergency release key into the keyhole.
- Turn the key to disengage the motor's clutch.
- The gate can now be pushed open or closed by hand.
- To re-engage the motor, turn the key back to its original position and remove it. Operate the gate with the remote to ensure the clutch is fully engaged.
7. Maintenance
Regular maintenance ensures the longevity and reliable operation of your gate opener system.
7.1. Monthly Inspection
- Check all mounting hardware for tightness.
- Inspect gate hinges and rollers for smooth operation. Lubricate if necessary.
- Examine all cables for wear, cuts, or damage.
- Ensure the gate moves freely without binding or excessive friction.
- Test the manual release mechanism.
7.2. Solar Panel Cleaning
Periodically clean the surface of the solar panel with a soft, damp cloth to remove dust, dirt, and debris. A clean panel ensures maximum charging efficiency.
7.3. Battery Care
The integrated lithium battery is designed for long life. Ensure the solar panel is clean and receiving adequate sunlight to keep the battery charged. If the gate is not used for extended periods, ensure the battery remains charged to prevent deep discharge.
8. Troubleshooting
This section provides solutions to common issues. For problems not listed here, contact customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| Gate does not respond to remote. |
|
|
| Gate opens but does not close. |
|
|
| Exit Wand not detecting vehicles. |
|
|
| Gate operates slowly or weakly. |
|
|
9. Specifications
| Feature | Detail |
|---|---|
| Model | MS650 |
| Max Gate Weight | 1760 lb (880 lb per arm) |
| Max Gate Length | 18 ft |
| Battery Type | 24V 6.0Ah Lithium-ion (integrated) |
| Solar Panel | 25W Monocrystalline |
| Remote Frequency | 433MHz Rolling Code |
| Exit Wand Cable Length | 50 ft (direct-burial) |
| Exit Wand Sensitivity | Adjustable (2-12 ft) |
| Operating Temperature | -4°F to 122°F (-20°C to 50°C) |
10. Warranty & Support
Blütezeit products are designed for durability and performance. This product comes with a standard manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty card included in your package or visit the official Blütezeit website for detailed warranty terms and conditions.
For technical assistance, troubleshooting, or to order replacement parts, please contact Blütezeit customer support. Have your model number (MS650) and purchase date ready when contacting support.
Blütezeit Customer Support:
- Website: Blütezeit Official Store
- Email: [Refer to product packaging or official website]
- Phone: [Refer to product packaging or official website]