Introduction
This manual provides detailed instructions for the safe and efficient operation, maintenance, and troubleshooting of your JONR H2 Pro Cordless Wet Dry Vacuum Cleaner. Please read this manual thoroughly before using the appliance and retain it for future reference.
Important Safety Instructions
To reduce the risk of fire, electric shock, or injury, always follow basic precautions, including the following:
- Read all instructions before using this appliance.
- Do not use outdoors or on wet surfaces.
- Do not allow to be used as a toy. Close attention is necessary when used by or near children.
- Use only as described in this manual. Use only manufacturer's recommended attachments.
- Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
- Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
- Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
- Do not handle plug or appliance with wet hands.
- Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
- Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
- Do not use without dust bag and/or filters in place.
- Turn off all controls before unplugging.
- Use extra care when cleaning on stairs.
- Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
- Do not use in an enclosed space where vapors are present from oil base paint, paint thinner, some mothproofing substances, flammable dust, or other explosive or toxic vapors.
- Connect to a properly grounded outlet only. See grounding instructions.
Product Overview
The JONR H2 Pro is a versatile cordless wet dry vacuum cleaner designed for efficient floor cleaning. It features hot water self-cleaning, an OdorLock system, powerful suction, and a lie-flat design for comprehensive coverage.
Figure 1: What's in the Box. This image displays the JONR H2 Pro Wet & Dry Vacuum Cleaner, Charging Station, Power Cord, User Manual, Maintenance Brush, and Floor Cleaning Solution.
Setup and Assembly
- Handle Installation: Align the handle with the main body and push it firmly until it clicks into place.
Video 1: Handle Installation. This video demonstrates how to align and secure the handle onto the main body of the JONR H2 Pro (0:14-0:17).
- Charging Station Setup: Connect the power cord to the charging station and plug it into a wall outlet. Place the charging station on a flat, stable surface.
Video 2: Charging Station Connection. This video shows how to connect the power plug to the charging station, indicating it is ready for use (0:17-0:26).
- Fill Clean Water Tank: Press the release button to detach the clean water tank. Fill it with clean water up to the maximum level. Add 1.5 to 2 capfuls of JONR cleaning solution. Securely close the tank lid and reattach the tank to the main body.
Video 3: Filling the Clean Water Tank. This video illustrates the process of filling the clean water tank with water and adding the cleaning solution, then reattaching it to the vacuum (0:26-0:47).
- Install Dirty Water Tank: Ensure the dirty water tank is properly closed and locked. Place it onto the base of the vacuum cleaner.
Video 4: Installing the Dirty Water Tank. This video demonstrates how to securely install the dirty water tank onto the vacuum cleaner's base (0:47-0:54).
Operating Instructions
- Power On: Press the power button (⑂) on the handle to turn on the appliance. It will automatically start in Automatic Mode.
Video 5: Starting the Vacuum. This video shows pressing the power button to start the JONR H2 Pro in Automatic Mode (0:54-1:00).
- Select Cleaning Mode: Press the mode selection button (⑁) to cycle through available cleaning modes:
- Automatic Mode: For general cleaning tasks.
- Intensive Mode: For stubborn stains and heavy dirt.
- Bathroom Mode: Designed for rapid water absorption and drying on bathroom surfaces.
Video 6: Mode Selection. This video demonstrates how to select different cleaning modes, including the specialized Bathroom Mode, using the mode button (1:10-1:14).
- Cleaning Operation: Guide the vacuum cleaner across the floor. The 180° lie-flat design allows access under furniture. The triple-edge design helps clean corners and edges effectively.
Figure 2: 180° Lie-Flat Cleaning. This image shows the JONR H2 Pro operating in a fully reclined position, demonstrating its ability to clean under low-clearance furniture.
Figure 3: Triple-Edge Cleaning. This image highlights the vacuum's design for cleaning close to edges and into corners, ensuring thorough coverage.
Maintenance and Care
- Self-Cleaning Cycle: After use, return the H2 Pro to the charging station. Press the self-cleaning button (⑁) to initiate the hot water self-cleaning and air-drying cycle.
Video 7: Initiating Self-Cleaning. This video shows placing the vacuum on its charging station and pressing the self-cleaning button to start the cycle (1:17-1:24).
Figure 4: Deep Self-Cleaning. This image illustrates the hot water self-cleaning and hot air drying process for the roller brush, ensuring hygiene and preventing odors.
- Empty and Clean Dirty Water Tank: After the self-cleaning cycle, remove the dirty water tank. Open it from both sides and empty the contents. Rinse the tank with clean water and use the provided maintenance brush to clean the liquid level sensor and any residue.
Video 8: Cleaning the Dirty Water Tank. This video demonstrates how to remove, empty, and clean the dirty water tank, including using the maintenance brush for the sensor (1:24-1:40).
- Clean Roller Brush and Filter Sponge: Remove the roller brush and rinse it with clean water. Remove the filter sponge and clean it under running water. Allow all cleaned components to air dry completely before reassembling.
Video 9: Roller Brush and Filter Cleaning. This video shows how to remove and rinse the roller brush and filter sponge, emphasizing air drying before reassembly (1:40-2:18).
- Reassembly: Once all parts are dry, reinsert the filter sponge, install the roller brush, and then reattach the dirty water tank.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Vacuum not turning on | Battery drained; Power button not pressed correctly. | Charge the vacuum; Ensure the power button is pressed firmly. |
| Poor suction | Dirty water tank full; Roller brush tangled; Filter clogged. | Empty dirty water tank; Clean roller brush; Clean or replace filter. |
| Water leakage | Dirty water tank not properly installed/locked; Clean water tank lid not sealed. | Ensure dirty water tank is securely installed and locked; Check clean water tank lid for proper seal. |
| Unpleasant odor | Dirty water tank not cleaned; Roller brush not cleaned. | Empty and thoroughly clean dirty water tank; Clean roller brush and allow to air dry. |
| Self-cleaning not starting | Vacuum not correctly placed on charging station; Clean water tank empty. | Ensure vacuum is properly docked; Fill clean water tank. |
Specifications
| Feature | Detail |
|---|---|
| Brand | JONR |
| Model | H2 Pro |
| Product Dimensions | 28L x 23W x 111H Centimetres |
| Item Weight | 7.89 Pounds (approx. 3.58 kg) |
| Clean Water Tank Capacity | 1500ml |
| Dirty Water Tank Capacity | 600ml (bottom-mounted) |
| Suction Power | 20,000Pa |
| Scrubbing Speed | 500BPM |
| Runtime | Up to 45 minutes |
| Self-Cleaning Temperature | 70°C Hot Water |
| Surface Recommendation | Hard Floor, Hardwood, Tile |
Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official JONR website or contact JONR customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.
Manufacturer Contact Information: Suzhoujingwakeji co.Itd, Unit A0403, Building 4, Suzhou International Science & Technology Park, No. 1355 Jinji Lake Avenue, Suzhou Industrial Park, Suzhou, Jiangsu 215000, China.
