NOVUS 24-Inch 2-Stage Gas Snow Blower

1. Safety Information

Always wear appropriate protective clothing, including gloves and eye protection, when operating this snow blower. Keep children and pets away from the machine during operation. Never leave the snow blower running in an enclosed area, as this can lead to carbon monoxide poisoning. Always turn off the engine and allow the auger to stop completely before removing any obstacles or making adjustments. Store the snow blower in a dry, well-ventilated area, and always follow the manufacturer's guidelines for fuel storage and disposal.

2. Product Overview

The NOVUS 24-inch 2-Stage Gas Snow Blower (Model NV24DSGL) is designed for efficient snow removal in various conditions. This self-propelled unit features a powerful 212cc OHV engine, electric start, and a durable steel auger to tackle heavy snow.

Key Features:

• Heavy-Duty Two-Stage Design: Clears snow up to 24 inches wide and 19 inches deep, throwing it up to 40 feet away. Ideal for large areas and heavy, wet snow.
• 212cc OHV Snow Engine: Provides reliable power and fuel efficiency for demanding snow conditions.
• Electric Start & Recoil Start Backup: Offers convenient starting options in cold weather.
• Self-Propelled Drive System: Features 6 forward and 2 reverse speed options for easy maneuverability.
• 190° Chute Rotation: Remote chute control allows for easy adjustment of snow discharge direction.
• 13" Pneumatic Snow Terrain Tires: Ensures excellent traction on various surfaces, including gravel and concrete.
• High-Impact, Adjustable Skid Shoes: Protects surfaces from scuffing and damage.
• Integrated LED Headlight: Enhances visibility for safe operation in low-light conditions.

Image: The NOVUS snow blower in action, highlighting its 24-inch clearing width and 19-inch snow depth capacity.

3. Assembly Instructions

Follow these steps to assemble your NOVUS 24-inch 2-Stage Gas Snow Blower. For a visual guide, refer to the 'NOVUS NV24DSGL Two-stage Gas Snow blower Quick Start Guide' video below.

Step-by-Step Assembly:

1. Install the Lower Handle:
   • Remove the 4 pre-installed flange bolts, lock washers, and flat washers from the frame.
   • Using the hardware removed earlier, install the lower handle onto the frame and tighten the bolts.
2. Install the Upper Handle:
   • With assistance, install the upper handle onto the lower handle. Secure it in place using the handle bolts, crank rod eyelet, wave washers, and handle knobs.
   • Insert the Z-bend ends of the auger and drive cables into the lower holes of the left and right engagement levers.
   • Install the threaded portion of the cables into the cable holders on the left and right handles, securing each cable with one nut above and one nut below.
   • Secure in place by tightening the M6 nuts.
3. Install the Tires:
   • Slide the wheel bushing and the tire onto the axle shaft.
   • Align the hole in the wheel with the axle shaft, insert the 6x35 pin, and secure it in place. Repeat for the other wheel.
4. Assemble the Chute Deflector and Chute Rotator:
   • Insert the plastic bushing into the front chute rotation bracket.
   • Slide the lower chute rotation rod through the bushing and secure with a 10 mm flat washer and a cotter pin.
   • Slide the upper chute rotator through the crank rod eyelet and into the lower chute rotator.
   • Align the holes of the upper and lower chute rotators. Secure in place by inserting and tightening 2 x M4x20 bolts and 2 x M4 locknuts with spring washers, turning the handle clockwise.
   • Align the 3 mounting holes of the discharge chute with the chute rotator disk holes.
   • Install the 3 x M6x16 square neck bolts from the inside of the discharge chute outward.
   • Secure the chute in place using 3 x 6 mm washers and 3 x M6 lock nuts.
5. Assemble the Drive Speed Control Rod:
   • Pull up the shift connecting plate and install the short bent end of the drive speed control rod.
   • Install the long bent end of the drive speed control rod to the control panel and secure it with 1 flat washer and 1 cotter pin.
   • Install the speed control handle using the 6 mm spring washer and turn the handle clockwise.
6. Connect Wiring Harness:
   • Connect the wiring harness assembly to the power take-off.
   • Secure the drive clutch cable and wiring harness assembly to the handle using a clamp.
   • Secure the auger clutch cable to the handle using a clamp.

4. Initial Setup: Oil & Fuel

Add Engine Oil:

1. Place the snow blower on a flat, level surface.
2. Using a funnel, add up to 20 fl. oz (600 mL) of oil (refer to the engine manual for recommended oil type). DO NOT OVERFILL.
3. Check the engine oil level and add oil as needed. Securely screw in the oil fill cap/dipstick.

Add Fuel:

1. Remove the fuel tank cap.
2. Add fresh, clean unleaded fuel with a minimum of 87 octane and a maximum of 10% ethanol to the fuel tank, leaving 1/4 inch of space from the top. DO NOT OVERFILL. Wipe up any spilled fuel immediately.
3. Reinstall the fuel tank cap by turning it clockwise until it stops.

5. Operating Instructions

Starting the Engine (Recoil / Pull Start):

1. Install the choke/throttle control lever onto the damper handle.
2. Insert the ON/OFF key.
3. Slide the choke/throttle control lever to the left to the "Choke" position.
4. Slide the fuel switch fully to the right to the "ON" position.
5. Firmly push in the primer 3 times with your thumb, holding it for a second before releasing each time.
6. Pull the starter handle slowly until resistance is felt, then pull rapidly.
7. Once the engine starts, slowly slide the choke/throttle control lever to the right to the "Run" position.

For electric start, plug in a three-prong cord to the designated port and press the electric start button. Allow the engine to run for 30-40 seconds before starting to throw snow.

Image: The NOVUS snow blower highlighting its reliable cold start features, including electric start and recoil backup.

Controls and Operation:

• Self-Propelled Drive: Use the drive lever on the handle to engage the self-propelled function. Select from 6 forward and 2 reverse speeds using the speed control lever to match your pace and snow conditions.
• Auger Engagement: Pull down the auger engagement lever to activate the steel auger and begin clearing snow.
• Chute Control: Utilize the remote chute control with 190° rotation to easily adjust the direction of the snow discharge.

Image: The self-propelled drive system of the NOVUS snow blower, illustrating the 6 forward and 2 reverse speed settings.

Image: The remote chute control of the NOVUS snow blower, demonstrating its 190-degree rotation capability.

Snow Clearing Tips:

• Clear snow in overlapping passes to ensure complete removal.
• Adjust the chute direction to throw snow away from cleared areas, buildings, or vehicles.
• For very deep snow, it may be necessary to clear in two passes, taking a partial cut first, then returning for the remaining snow.

Image: The NOVUS snow blower demonstrating its 40-foot snow throwing distance.

6. Maintenance

Regular maintenance ensures optimal performance and extends the life of your snow blower. Always refer to the full owner's manual for detailed maintenance schedules and procedures.

General Maintenance Tips:

• Engine Oil: Check oil level before each use and change according to the engine manual's recommendations.
• Fuel: Use fresh, clean unleaded gasoline. For long-term storage, use a fuel stabilizer or drain the fuel tank.
• Spark Plug: Inspect and clean or replace the spark plug annually.
• Auger and Impeller: Regularly inspect for wear or damage. Replace worn parts to maintain clearing efficiency.
• Skid Shoes: Check for wear and adjust or replace as needed to protect surfaces.
• Tires: Ensure tires are properly inflated and have good tread for optimal traction.
• Cleaning: After each use, clear any snow or ice buildup from the auger housing, chute, and engine area.
• Storage: Store the snow blower in a dry, well-ventilated area away from direct sunlight and extreme temperatures.

7. Troubleshooting

This section provides solutions for common issues you might encounter with your snow blower. For more complex problems, contact customer support.

Common Issues and Solutions:

• Engine Fails to Start:
  • Check fuel level and ensure fresh fuel is used.
  • Verify the ON/OFF key is fully inserted.
  • Ensure the choke is in the correct position for starting.
  • Check the spark plug for fouling or damage.
• Snow Blower Not Throwing Snow:
  • Check for clogs in the auger housing or discharge chute. Always turn off the engine and remove the key before clearing clogs.
  • Inspect the auger and impeller for damage or wear.
• Loss of Drive Power:
  • Check the drive belt for wear or breakage.
  • Ensure the drive engagement lever is fully engaged.

8. Specifications

9. Warranty and Support

All NOVUS Snow blowers come with a 2-year limited warranty and lifetime technical support. For assistance, please contact NOVUS customer service.

You can also visit the official NOVUS Store for more product information and support resources.