1. Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your TUMMASTER ARGB Fan HUB J-09. This device is designed to centralize control for multiple Addressable RGB (ARGB) fans and other 5V 3-pin ARGB devices, as well as PWM fans, within your PC system. It offers convenient control options via an RF remote or motherboard synchronization.
2. Product Overview
2.1 Key Features
- 9-Port ARGB & PWM Control: Supports up to 9 ARGB (5V 3-pin) devices and 9 PWM (4-pin) fans for centralized management.
- Magnetic Mounting: Features magnetic suction for easy and secure placement within your PC chassis.
- RF Remote Control: Allows for convenient adjustment of lighting effects and fan speeds without opening the PC case.
- SATA Power Input: Provides stable and sufficient power directly from your power supply, preventing voltage loss and ensuring efficient operation for all connected devices.
- PWM Intelligent Temperature Control: Supports fan speed reading and automatic PWM fan regulation. Note that due to IC reading principles, only the speed of the fan connected to the designated red interface is recognized.
- ARGB Lighting Synchronization: Compatible with 5V 3-pin ARGB interfaces for synchronized lighting effects with your motherboard (if supported).
- Compact Design: With dimensions of approximately 3.83 x 2.33 x 0.6 inches, it offers a small footprint for tidy cable management.
2.2 Package Contents
Please verify that all items are present in your package:
- TUMMASTER ARGB Fan HUB J-09
- SATA Power Cable
- ARGB Synchronization Cable
- PWM Synchronization Cable
- RF Remote Control
- Installation Guide (this document)
Image: The TUMMASTER ARGB Fan HUB J-09, accompanied by its RF remote control, SATA power cable, ARGB cable, and PWM cable, illustrating the complete package contents.
3. Safety Information
Before installation, please read and understand the following safety precautions:
- Always disconnect your PC from the power outlet before installing or removing any components.
- Handle components with care to avoid damage from electrostatic discharge (ESD). Consider using an anti-static wrist strap.
- Ensure all cables are connected firmly and in the correct orientation. Incorrect connections, especially for ARGB, can damage the hub or connected devices.
- Important ARGB Note: The hub supports 5V 3-pin ARGB devices. Do NOT connect 12V 4-pin RGB devices to the ARGB ports. Connecting a 12V device to a 5V port will cause irreversible damage. Always check the arrow marked on the ARGB equipment plug and insert it in the direction of 5V.
- Keep the hub away from liquids and extreme temperatures.
4. Setup and Installation
Follow these steps to install your ARGB Fan HUB J-09:
4.1 Mounting the Hub
- Identify a suitable flat metal surface within your PC chassis. The hub features a magnetic base for easy attachment.
- Place the hub firmly onto the chosen surface. Ensure it is secure and does not obstruct airflow or other components.
Image: The TUMMASTER ARGB Fan HUB J-09 showcasing its magnetic design, allowing for convenient placement on any metal surface inside a computer case.
4.2 Connecting Power
- Locate an available SATA power connector from your PC's power supply unit (PSU).
- Connect the provided SATA Power Cable to the 'POWER IN' port on the ARGB Fan HUB.
- Connect the other end of the SATA Power Cable to the SATA power connector from your PSU.
4.3 Connecting Fans and ARGB Devices
Refer to the connection diagram below for visual guidance.
Image: A detailed diagram illustrating the connection points on the TUMMASTER ARGB Fan HUB J-09 for SATA power, ARGB devices, PWM fans, motherboard sync, and chassis key. It also displays the functions of the RF remote control.
- ARGB Devices (5V 3-pin): Connect your ARGB fans, LED strips, or other 5V 3-pin ARGB devices to the 'ARGB' ports on the hub. Ensure the arrow on the ARGB connector aligns with the 5V pin on the hub.
- PWM Fans (4-pin): Connect your PWM fans to the 'PWM' ports on the hub. The red PWM port (often labeled FAN 1 or CPU FAN) is designated for fan speed reading. Connect your CPU fan to this port if you wish to monitor its speed.
- Motherboard Synchronization (Optional): If your motherboard supports 5V 3-pin ARGB (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync), connect the provided ARGB Synchronization Cable from the 'M/B' port on the hub to your motherboard's 5V 3-pin ARGB header. This allows software control of lighting effects. If your motherboard does not support 5V ARGB, you do not need to connect this cable.
- Chassis Key Control (Optional): Connect your PC's reset button cable or a dedicated chassis key cable to the 'RESET' or 'FP' port on the hub. This allows you to cycle through lighting modes using the physical button on your PC case.
5. Operating Instructions
Once installed and powered on, you can control your connected fans and ARGB devices using the RF remote control or motherboard software (if connected).
5.1 RF Remote Control Functions
The included RF remote control provides direct access to various lighting effects and fan speed adjustments. Refer to the remote diagram in Section 4.3 for button layout.
- On/Off: Turns the lighting effects on or off.
- AUTO: Cycles through pre-programmed lighting modes automatically.
- S+/S-: Adjusts the speed of dynamic lighting effects or fan speed (if applicable).
- M+/M-: Cycles through different lighting modes.
- Color Buttons: Selects static colors for your ARGB devices.
- Press 5 times in a row: This action is typically used to switch between remote control mode and motherboard synchronization mode. The remote control will flash red twice to confirm the change.
5.2 Motherboard Synchronization
If the hub is connected to your motherboard's 5V 3-pin ARGB header, you can use your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) to control the lighting effects of all connected ARGB devices. Ensure the hub is set to motherboard sync mode using the remote control (refer to 'Press 5 times in a row' function above).
5.3 Chassis Key Control
If your PC's reset button or a dedicated chassis key is connected to the 'RESET' or 'FP' port, pressing this button will cycle through the available lighting modes.
6. Maintenance
To ensure optimal performance and longevity of your TUMMASTER ARGB Fan HUB J-09 and connected components, consider the following maintenance tips:
- Dust Removal: Periodically clean the inside of your PC case to prevent dust buildup on the hub and fans, which can hinder cooling and affect performance. Use compressed air or a soft brush.
- Cable Management: Ensure all cables are neatly routed and secured to prevent interference with fan blades or other moving parts.
- Connection Check: Occasionally verify that all cables (power, ARGB, PWM) are securely connected to the hub and other components.
7. Troubleshooting
If you encounter issues with your ARGB Fan HUB, refer to the following troubleshooting guide:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fans or ARGB devices are not lighting up or spinning. | No power to the hub; incorrect ARGB voltage; loose connections. | Ensure the SATA power cable is securely connected to both the hub and the PSU. Verify that 5V 3-pin ARGB devices are connected to ARGB ports, not 12V 4-pin RGB. Check all ARGB and PWM connections for tightness. |
| ARGB lighting is not synchronizing with the motherboard. | Hub not in motherboard sync mode; incorrect motherboard connection; motherboard does not support 5V ARGB. | Press the remote control's 'AUTO' button 5 times in a row to switch to motherboard sync mode (remote will flash red twice). Ensure the ARGB Synchronization Cable is correctly connected from the hub's 'M/B' port to your motherboard's 5V 3-pin ARGB header. Confirm your motherboard supports 5V 3-pin ARGB. |
| Remote control is not working. | Battery depleted; signal obstruction; hub in motherboard sync mode. | Replace the remote control battery. Ensure there are no obstructions between the remote and the hub. If the hub is in motherboard sync mode, press the 'AUTO' button 5 times to switch back to remote control mode. |
| Fan speeds are not being regulated or read correctly. | Incorrect PWM fan connection; limitation of PWM IC. | Ensure PWM fans are connected to the 4-pin PWM ports. For speed reading, connect the primary fan (e.g., CPU fan) to the designated red PWM port. Note that only the speed of the fan connected to the red interface is typically recognized by the system. |
| Loose fan port connections. | Manufacturing tolerance; repeated forceful insertions. | Handle fan connectors with care during insertion and removal. Ensure connections are firm but avoid excessive force. If a port is excessively loose, consider using an alternative port if available, or contact support. |
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | J-09 |
| Product Dimensions | 3.83"L x 2.33"W x 0.6"H (9.73 x 5.92 x 1.52 cm) |
| Weight | 3.74 ounces (106 grams) |
| Brand | TUMMASTER |
| ARGB Voltage | 5V DC |
| Fan Voltage | 12V DC |
| Current | 7A (Maximum) |
| Wattage | 110 watts (Maximum) |
| Cooling Method | Forced Air (via connected fans) |
| Compatible Devices | Desktop PCs |
| Material | Plastic |
| Mounting | Magnetism |
| UPC | 795276571193 |
| Batteries | 1 Unknown battery required (included for remote) |
9. Warranty and Support
For warranty information and technical support, please refer to the official TUMMASTER website or contact your retailer. Keep your purchase receipt as proof of purchase.
