1. Introduction
Thank you for choosing the GAOMON Queen Size Wood Platform Bed Frame. This manual provides essential information for safe assembly, proper use, and maintenance of your new bed frame. Please read it thoroughly before assembly and retain it for future reference.
2. Safety Information
- Read all instructions carefully before assembly.
- Keep all small parts and packaging materials away from children.
- Assemble the bed frame on a soft, clean surface to prevent scratches.
- Ensure all bolts and screws are securely tightened before use. Periodically check and re-tighten as necessary.
- Do not use power tools for assembly unless specifically instructed, as over-tightening may damage components.
- Do not stand on or jump on the bed frame.
- Ensure the mattress fits properly within the frame dimensions.
- Maximum weight capacity should not be exceeded.
3. Package Contents
Before beginning assembly, verify that all parts listed below are present and undamaged. If any parts are missing or damaged, please contact customer support.

Image: All components of the GAOMON bed frame laid out, including side rails, support beams, wooden slats, and hardware. This image helps users confirm they have all necessary parts before starting assembly.
Typical components include:
- Side Rails (Left and Right)
- End Rails (Head and Foot)
- Center Support Beam(s)
- Wooden Slats
- Support Legs (if applicable)
- Hardware Pack (bolts, washers, Allen wrench)
4. Setup and Assembly
Assembly typically requires two adults. Please follow these general steps. Refer to the included instruction sheet for detailed, step-by-step diagrams specific to your model.
- Unpack Components: Carefully remove all parts from the packaging and lay them out on a clean, soft surface.
- Assemble Frame: Connect the side rails to the head and foot rails using the provided bolts and Allen wrench. Ensure all connections are snug but do not fully tighten until the entire frame is assembled.
- Install Center Support: Attach any center support beams or legs as indicated in your specific instructions.
- Place Slats: Lay the wooden slats across the frame. Ensure they are evenly spaced and secured according to the instructions (e.g., using plastic caps or screws).
- Final Tightening: Once all components are in place, go back and fully tighten all bolts and screws. Do not overtighten.
- Position Bed: Carefully move the assembled bed frame to its desired location.

Image: Detail showing the "Shake-Resistant Snap Fit" and "Easy to Assemble" features of the frame's corner connections, highlighting the robust construction.

Image: Detailed view of the "Sturdy Wood Slats" and "Solid Metal Fasteners" demonstrating the durable and supportive slat system designed for mattress stability.
5. Operating and Usage
Your GAOMON platform bed frame is designed to support your mattress directly, eliminating the need for a box spring.
- Mattress Placement: Carefully place your queen-size mattress directly onto the wooden slats. Ensure it is centered and fully supported by the frame.
- Weight Distribution: Distribute weight evenly across the bed. Avoid concentrating heavy loads in one small area.
- Movement: When moving the bed frame, lift it rather than dragging it to prevent damage to the frame or your flooring.

Image: A GAOMON Queen size bed frame with a mattress and bedding, set in a modern bedroom with light-colored walls and minimalist decor, showcasing its aesthetic integration.
6. Maintenance
- Cleaning: Wipe the wood surfaces with a soft, damp cloth. Avoid using harsh chemicals or abrasive cleaners, which can damage the finish.
- Regular Checks: Periodically (every 3-6 months) check all bolts and screws to ensure they remain tight. Re-tighten if necessary.
- Avoid Moisture: Keep the bed frame away from excessive moisture or direct sunlight to prevent warping or fading of the wood finish.
7. Troubleshooting
- Squeaking Noises:
- Ensure all bolts are securely tightened. Check that slats are properly seated and not rubbing against the frame. If the issue persists, try placing felt pads between slats and the frame.
- Instability/Wobbling:
- Verify that the bed frame is on a level surface. Re-check all connections to ensure they are fully tightened. Ensure all support legs (if any) are making firm contact with the floor.
- Slats Shifting:
- Ensure slats are correctly installed in their designated positions. If your model uses plastic caps, ensure they are fully engaged. If slats are designed to be screwed in, confirm all screws are present and tight.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | GAOMON |
| Model Number | 1M_G3p4sljm7zFyMormoywcy5Z |
| Size | Queen |
| Material | Engineered Wood |
| Product Dimensions (L x W x H) | 81.5"L x 61.81"W x 10.24"H |
| Color | Natural Walnut |
| Item Weight | 54.5 pounds |
| Assembly Required | Yes (Instructions Included) |
| Box Spring Required | No |

Image: A detailed chart illustrating standard mattress sizes, corresponding mattress fit dimensions, and the overall bed frame dimensions for Twin, Twin XL, Full, Queen, King, and California King sizes. This helps users confirm the correct size.
9. Warranty and Support
For warranty information or customer support, please refer to the documentation included with your purchase or visit the official GAOMON website. If you have any questions regarding assembly, missing parts, or product functionality, please contact GAOMON customer service directly.
You can visit the GAOMON Store on Amazon for more information: GAOMON Store