TITANO E5 Ergonomic Office Chair Instruction Manual
Model: E5
1. Introduction and Safety Information
Thank you for choosing the TITANO E5 Ergonomic Office Chair. This manual provides essential information for the safe assembly, operation, and maintenance of your chair. Please read these instructions carefully before use and retain them for future reference.
Safety Warnings
- Maximum Weight Capacity: The TITANO E5 chair is designed to support a maximum weight of 150 kg (330 lbs). Do not exceed this limit to prevent damage to the chair or personal injury.
- Ensure all components are securely fastened before use. Regularly check and tighten fasteners as needed.
- Keep hands and fingers clear of moving parts during adjustment.
- Use the chair on a level surface to prevent tipping.
2. Setup (Assembly)
The TITANO E5 chair is designed for straightforward assembly, typically taking approximately 15 minutes. All necessary tools are included in the package.
Assembly Steps
- Unpack all components and verify against the parts list provided in your package.
- Attach the casters to the five-star base by pressing them firmly into the holes.
- Insert the gas lift into the center hole of the five-star base.
- Attach the seat mechanism to the underside of the seat cushion using the provided screws. Ensure the front of the mechanism aligns with the front of the seat.
- Place the assembled seat onto the gas lift.
- Attach the backrest to the seat mechanism using the designated screws.
- Mount the armrests to the seat base.
- Install the headrest into the top of the backrest.
- Ensure all screws are tightened, but do not overtighten.
3. Operating (Adjustments)
The TITANO E5 chair offers multiple adjustment options to customize your seating experience for optimal ergonomic support.

This image highlights the customizable features of the TITANO E5 chair. It shows how the 4D armrests can be adjusted in multiple directions (height, depth, width, and angle). The headrest is shown with height and tilt adjustment. The seat height and depth adjustment mechanisms are also visible, along with the 2D adjustable lumbar support, which can be moved vertically and horizontally.
Seat Height Adjustment
- To raise the seat: Lift the lever located on the right side of the seat while taking your weight off the chair. Release the lever at the desired height.
- To lower the seat: Lift the lever while seated on the chair. Release the lever at the desired height.
Seat Depth Adjustment
- Locate the lever or button on the left side, beneath the seat.
- While holding the lever/button, slide the seat forward or backward to achieve optimal thigh support, leaving a small gap between the edge of the seat and the back of your knees. Release the lever/button to lock the position.
4D Armrest Adjustment
The armrests can be adjusted in four dimensions:
- Height: Press the button on the side of the armrest and move it up or down. Release the button to lock.
- Depth (Forward/Backward): Slide the armrest pad forward or backward.
- Width (In/Out): Slide the armrest pad inward or outward.
- Angle (Pivot): Rotate the armrest pad left or right.
Headrest Adjustment
- Height: Grasp the headrest and slide it up or down to position it comfortably behind your head and neck.
- Tilt: Adjust the angle of the headrest by tilting it forward or backward.
Lumbar Support Adjustment
The lumbar support is adjustable in 2 dimensions:
- Height: Slide the lumbar support mechanism up or down the backrest to align with the natural curve of your lower back.
- Depth: Rotate the knob on the side of the lumbar support to increase or decrease the support's protrusion.
Tilt Function and Resistance
- Activate/Deactivate Tilt: Pull the main lever (usually the same as seat height) outwards to allow the backrest to recline. Push it inwards to lock the backrest in an upright position.
- Tilt Resistance: Rotate the large round knob located underneath the seat, at the front. Turn clockwise to increase tilt resistance (making it harder to recline) and counter-clockwise to decrease resistance (making it easier to recline).
4. Maintenance
Proper maintenance ensures the longevity and optimal performance of your TITANO E5 chair.
Cleaning Instructions
- Fabric/Mesh: For general cleaning, wipe with a damp cloth. For deeper cleaning, hand wash with mild soap and water. Avoid harsh chemicals or abrasive cleaners.
- Plastic/Metal Parts: Wipe with a soft, damp cloth.
General Care
- Periodically check all screws and bolts and tighten them if necessary.
- Avoid exposing the chair to direct sunlight for extended periods to prevent material degradation.
- Do not stand on the chair or use it as a ladder.
5. Troubleshooting
If you encounter any issues with your TITANO E5 chair, refer to the following common solutions:
- Chair Squeaks: Check and tighten all assembly screws. A small amount of silicone spray on moving metal parts (e.g., springs in the mechanism) may help.
- Difficulty Adjusting Height: Ensure the gas lift lever is fully engaged. If the gas lift is unresponsive, it may need replacement.
- Chair Wobbles: Verify that the five-star base is correctly assembled and all casters are fully inserted. Ensure all screws connecting the seat and backrest are tight.
- Casters Not Rolling Smoothly: Check for debris (hair, dust) wrapped around the caster wheels and clean them.
If problems persist after attempting these solutions, please contact customer support.
6. Specifications
Key technical specifications for the TITANO E5 Ergonomic Office Chair:

This diagram illustrates the key dimensions of the TITANO E5 chair. The seat height is adjustable from 42 cm to 53 cm. The seat depth is 43 cm, and the seat width is 50 cm. The backrest height is 47 cm, and the headrest adds an additional 18 cm in height. The overall width of the chair is 70 cm, and the headrest width is 34 cm. The maximum load capacity is 150 kg.
| Attribute | Value |
|---|---|
| Brand | TITANO |
| Model Number | E5 |
| Color | Black |
| Product Dimensions (L x W x H) | 65 x 65 x 129 cm |
| Item Weight | 19.1 Kilograms |
| Maximum Load Capacity | 150 kg |
| Frame Material | Reinforced Nylon |
| Upholstery Material | Breathable Mesh, High-density Cold-molded Foam (seat) |
| Gas Lift Class | Class 4 |
| Caster Type | 60mm Polyurethane (PU) wheels |
| Certifications | EN 1335 (TÜV-SÜD tested) |

This image details the robust construction of the chair's base. It features a stable 70 cm chrome five-star base, equipped with premium 360-degree silent polyurethane wheels designed to protect floors. The chair's height adjustment is powered by a safety-tested Class 4 gas lift, ensuring smooth and reliable operation.
7. Warranty and Support
TITANO is committed to providing high-quality products and customer satisfaction.
Spare Parts Availability
Spare parts for the TITANO E5 chair are available for 5+ years from the date of purchase, ensuring long-term usability and maintenance.
Customer Support
If you have any questions, require assistance with assembly, or encounter any issues with your chair, please do not hesitate to contact our customer service team. We offer fast customer service in your language.
Please refer to your purchase documentation or the TITANO website for specific contact details.