fishkeeper Automatic Fish Feeder (Model FK092-NEW) User Manual

Introduction

This manual provides detailed instructions for the safe and efficient use of your fishkeeper Automatic Fish Feeder, Model FK092-NEW. Please read this manual thoroughly before operating the device to ensure proper function and longevity.

Package Contents

Verify that all items listed below are included in your package:

• 1 x fishkeeper Automatic Fish Feeder (Model FK092-NEW)
• 1 x Desiccant Container
• 1 x Feed Outlet Chute
• 2 x Foot Supports
• 1 x 6.56ft/2m Power Cord (6V 1A)
• 3 x Feeding Reduction Clips
• 2 x Nails
• 1 x User Manual

Setup

1. Power Options

The fishkeeper Automatic Fish Feeder offers two power supply options:

• AC Power: Use the included 6.56ft/2m power cord for direct connection to an AC outlet.
• Battery Power: For cordless operation, install 4 AAA batteries (not included). This provides approximately 1-6 months of battery life.

2. Installation Options

The feeder offers two installation methods:

1. Secure to the Pond:
   • Install the foot supports outwards on the base of the feeder.
   • Secure the foot supports with the provided nails to a hard surface next to your pond (e.g., solid ground, wooden flooring, or tile).
2. Placed on the Aquarium Cover:
   • Install the feed outlet chute onto the feeder.
   • Place the feeder directly on top of your indoor aquarium cover, ensuring the feed chute is positioned over the water.

3. Filling the Feeder

The feeder has a 2.8L capacity. To fill:

1. Open the top lid of the feeder.
2. Pour the desired fish food into the container. Ensure the food type is suitable (small pellet, large pellet, strip, corn & nuts).
3. Close the lid securely. The lid features a locking mechanism to prevent accidental spillage and a dedicated desiccant slot to keep food dry (desiccant not included).

Operating Instructions

1. LCD Display Overview

The feeder features an LCD display and control buttons for programming. Familiarize yourself with the display elements:

• MODE: Button to switch between modes.
• SET: Button to confirm settings.
• +: Button to increase values or cycle through options.
• -: Button to decrease values or cycle through options.
• Now: Indicates current time setting.
• Vol (Feeding Volume): Indicates the number of times the feeder dispenses food per feeding session (1-99 portions).
• Timing: Indicates specific feeding times (up to 6 meals per day in Custom Mode).
• Int (Precise Mode Feeding Interval): Sets the feeding interval (e.g., "0" for daily, "1" for every other day).

2. Current Time Calibration

To set the current time on your feeder:

1. Press the MODE button to display the "Now" part.
2. Press and hold the SET button for 3 seconds.
3. Use the + or - buttons to adjust the hour.
4. Press SET again to switch to minutes.
5. Use the + or - buttons to adjust the minute.
6. Press SET again to finish setting the time.

3. Setting Up Lazy Mode (Preset Timer)

Lazy Mode offers 9 preset feeding schedules for convenience:

To activate Lazy Mode:

1. Press and hold the MODE, SET, and + buttons simultaneously for 3 seconds to access the preset feeding schedules.
2. Press the + button to cycle through and select your desired feeding schedule.
3. Press SET to confirm the schedule. The display will automatically jump to "Vol" setting.
4. Use the + and - buttons to adjust the portion size (number of dispenses, 1-99).
5. Press SET to confirm the portion setting. A small "h" icon will appear in the lower-right corner of the time display, indicating Lazy Mode is active.

4. Setting Up Custom Timed Mode (Precise Mode)

Custom Mode allows you to set up to 6 specific feeding times per day:

1. First, reset to factory settings by pressing and holding SET and - buttons for 3 seconds.
2. Press the MODE button twice to access the "Timing" settings.
3. Press and hold the SET button for 3 seconds to start setting the first meal time.
4. Use the + or - buttons to set the hour, then press SET to switch to minutes. Repeat for minutes.
5. Press SET again to set the second meal time, and continue this process for subsequent meals (up to 6).
6. To exit without setting additional times, press the MODE button. This will automatically jump to the "Int" setting page.
7. Press and hold SET for 3 seconds to enter "Int" settings. Use + or - to adjust the feeding interval (0 for daily, 1 for every other day, etc.). Press SET to confirm.
8. Finally, for "Vol" (Feeding Volume) setting: Press the MODE button until "Vol." appears. Then press and hold SET for 3 seconds to enter "Vol." settings. Use + or - to adjust the portion (number of dispenses, 1-99) and press SET to confirm the setting.

5. Adjusting Food Portion Size (Using Reduction Clips)

The feeder includes 3 reduction clips to control the dispensed food portion, suitable for fish pellet sizes 2-10mm. These clips can be disassembled to achieve a larger discharge aperture if needed.

6. Removing the Reduction Clip

To remove a reduction clip for larger portions or cleaning:

1. Press and hold the - button for 3 seconds. The display will show "OPEN".
2. Gently shake the feeder to help release the clip.
3. Use your finger to remove the clip from the feed outlet.

Note:

• It is recommended to adjust the "Vol" setting to achieve the desired feeding portion.
• It is recommended to remove the clip only when using large-sized pellets.

Maintenance

Regular maintenance ensures optimal performance and longevity of your fishkeeper Automatic Fish Feeder.

1. Preventing Moisture and Clumping

• The feeder features a waterproof snap-on lid and a rain-proof feed outlet chute design to protect food from moisture.
• Utilize the dedicated desiccant slot on the lid to insert a desiccant packet (not included) to further keep food dry and fresh.
• The internal rotatable rotor helps prevent food from clumping or getting stuck during dispensing.

2. Cleaning

To clean the feeder:

• Ensure the feeder is powered off and disconnected from any power source.
• Remove any remaining food from the hopper.
• Disassemble the feed outlet chute and any reduction clips for thorough cleaning.
• Wipe down the interior and exterior of the feeder with a damp cloth. Avoid submerging the main unit in water.
• Clean the feed outlet chute and reduction clips with mild soap and water, then rinse thoroughly and allow to air dry completely before reassembling.
• Ensure all parts are completely dry before refilling with food and resuming operation.

Troubleshooting

If you encounter issues with your fishkeeper Automatic Fish Feeder, refer to the following common problems and solutions:

Specifications

Warranty and Support

For warranty information or technical support, please refer to the contact details provided with your purchase or visit the official fishkeeper website. Keep your purchase receipt for warranty claims.