Introduction
The hygger Lite Wave Maker is designed to create natural water currents within your aquarium, promoting a healthy and dynamic environment for fish, corals, and invertebrates. This adjustable circulation pump features a magnetic base for secure and easy installation, offering multiple wave-making modes and precise flow rate adjustments. This manual provides essential information for the safe and effective use of your wave maker.
Safety Instructions
- Always unplug the device from the power outlet before performing any maintenance, cleaning, or installation procedures.
- Ensure your hands are completely dry before handling the power adapter or plugging in the device.
- Do not operate the wave maker if the power cord, plug, or any other component is damaged. Contact customer support for assistance.
- This device is intended for indoor aquarium use only. Do not use it for purposes other than those specified.
- Keep the device and its components out of reach of children and pets.
- The controller unit is not waterproof. Ensure it remains dry and away from water splashes.
- Ensure the pump is fully submerged in water during operation to prevent dry running and potential damage.
Product Overview
Components: Front Shell, Impeller, Pump Motor, Magnetic Base, Hard Protection Cover.
System Overview: Wave maker pump, controller, DC adapter, and connecting cables.
The hygger Lite Wave Maker consists of a compact pump unit, a magnetic base for attachment, a wired controller, and a DC power adapter. The pump is designed for quiet operation and efficient water circulation.
Setup Instructions
- Prepare the Aquarium: Ensure your aquarium is clean and filled with water to the desired level.
- Install the Pump:
The wave maker attaches to the aquarium glass using its magnetic base. Place the pump unit inside the tank and align the external magnet on the outside of the glass. The magnetic hold is suitable for glass thickness up to 6mm. Ensure the hard protection cover is securely aligned on the pump to prevent small fish or invertebrates from being drawn in.
- Positioning: Position the wave maker to achieve the desired water flow pattern. It can be placed higher for surface waves, in the middle for general circulation, or lower to stir up bottom debris. The pump is recommended for 10 to 50-gallon freshwater and saltwater aquariums up to 31 inches long.
- Connect the Controller: Connect the pump cable to the controller.
- Connect Power: Connect the DC power adapter to the controller, then plug the adapter into a suitable electrical outlet (AC 110-240V).
- Initial Check: Once powered, the pump should begin operating according to its default settings. Observe the water flow and adjust as needed.
Operating Instructions
The hygger Lite Wave Maker features a smart controller with a digital display and intuitive buttons for adjusting settings.
The controller allows adjustment of wave patterns, speed, and frequency.
Controller Functions:
- LED Digital Display: Shows current frequency (P) and flow rate (F) settings.
- M/FE Button: Press to cycle through wave-making modes. Press and hold to activate Feeding Mode.
- '+' Button: Increases flow rate or wave frequency.
- '-' Button: Decreases flow rate or wave frequency.
Wave-Making Modes:
Select from four distinct wave patterns to simulate natural aquatic environments.
- Constant Wave Mode (01): Provides a stable and continuous water flow.
- Pulse Wave Mode (02): Delivers short bursts of strong water flow.
- Sine Wave Mode (03): Mimics the rise and fall of tides with a dynamic water flow.
- Random Wave Mode (04): Generates automatically changing water flow speeds.
Adjusting Flow Rate and Frequency:
Adjust flow rate using the '+' and '-' buttons (F1 to F10).
Adjust wave frequency using the '+' and '-' buttons (P1 to P10).
Use the '+' and '-' buttons to adjust the flow rate (10 levels, displayed as F1-F10) and wave frequency (10 levels, displayed as P1-P10) to suit your aquarium's specific needs.
Feeding Mode:
Press and hold the 'M/FE' button to activate feeding mode, pausing flow for 9 minutes.
To feed your aquatic inhabitants, press and hold the 'M/FE' button. The pump will pause operation for 9 minutes, allowing food to be consumed without being immediately dispersed by the current. The pump will automatically resume its previous settings after 9 minutes.
Official Product Video:
This video demonstrates the installation and various operating modes of the hygger Lite Wave Maker, including how to adjust settings and utilize the feeding mode.
Maintenance
Regular cleaning of your wave maker is essential to ensure optimal performance and longevity. If the impeller becomes stuck or blocked, follow these steps:
- Disconnect Power: Always unplug the wave maker from the power outlet before cleaning.
- Remove from Tank: Carefully remove the pump unit from the aquarium.
- Disassemble:
Twist the front shell counter-clockwise to detach it. Separate the outer cage and carefully take out the impeller. The magnetic base and pump motor remain connected to the cable.
- Clean Components: Rinse all disassembled parts (front shell, outer cage, impeller) under clean water. Use a soft brush or cloth to remove any algae, debris, or mineral buildup. Ensure the impeller spins freely.
- Reassemble: Carefully reassemble the components in reverse order. Ensure the impeller is correctly seated and the front shell is securely twisted back into place.
- Reinstall: Place the cleaned wave maker back into the aquarium and reconnect the power.
Troubleshooting
The controller's digital display may show error codes to indicate specific issues:
Error codes provide quick identification of common problems.
| Error Code | Description | Solution |
|---|---|---|
| E01, E02, E03 | Current Voltage Fault (Overvoltage, Undervoltage, Overcurrent) | Replace the controller. |
| E04 | Dry Running | Ensure the pump is fully submerged in water. |
| E05 | Motor Blockage | Disassemble the pump and clean the impeller as described in the Maintenance section. |
If you encounter an issue not listed here or if the suggested solutions do not resolve the problem, please contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | HG172NEW |
| Power | 6 Watts |
| Max Flow Rate | 792 GPH (Gallons Per Hour) |
| Applicable Aquarium Size | 10-50 Gallons (up to 31" long tanks) |
| Max Glass Thickness | 6 mm |
| Voltage Input | AC 110-240V |
| Voltage Output | DC 12V |
| Pump Dimensions | 1.6 x 1.9 inches |
| Cord Length | 4.7 FT (pump to controller) + 7.2 FT (controller to adapter) |
| Material | Stainless Steel (internal components), Plastic (housing) |
| Color | Black |
Warranty Information
Specific warranty details are not provided in the product data. Please refer to the product packaging or contact the manufacturer directly for warranty terms and conditions.
Customer Support
For further assistance, technical support, or inquiries regarding your hygger Lite Wave Maker, please visit the official hygger store or contact their customer service department.
hygger Store: https://www.amazon.com/stores/hygger/page/42A01E3C-6B12-4432-9B13-22DAE2FF23FC