Introduction
This manual provides detailed instructions for the safe and effective use of the URIT PFS-30A 5-in-1 Lipid Test Kit. This device is designed for home use to measure Total Cholesterol, Triglycerides, HDL, LDL, and TC/HDL ratio from a small blood sample.
Important Safety Information
Legal Disclaimer: Statements regarding dietary supplements have not been evaluated by the FDA and are not intended to diagnose, treat, cure, or prevent any disease or health condition.
This device is for in-vitro diagnostic use only. Consult a healthcare professional for interpretation of results.
Package Contents
Image Description: A flat lay of all components included in the URIT PFS-30A 5-in-1 Lipid Test Kit. It shows the monitor, lancing device, 10 test strips, 10 capillary tubes, a code card, 10 lancets, and a storage bag.
- Blood Lipid Analyzer (Monitor)
- Lancing Device
- Test Strips (10 Cholesterol Test Strips)
- Sterile Lancets (10 pieces)
- Capillary Tubes (10 pieces)
- Code Card
- Batteries (AAA, 2 pieces)
- Storage Bag
- Instruction Manual (this document)
Setup
1. Lancing Device Preparation
Video Description: This video demonstrates how to install the lancet into the lancing device, adjust depth, and arm it.
- Tighten the lancing device adjustment head.
- Place a new blood collection needle into the needle hub.
- Screw off the lancet cap vertically.
- Rescrew the adjustment head back on.
- Adjust the lancet depth (recommended to start with 2; for thicker skin, switch to a higher number).
- Pull the lancet handle backward until you hear a "click" sound to arm the device.
2. Inserting the Code Card
Insert the code card into the meter while the device is powered off. The meter will display the code. Verify that the code on the screen matches the code on the test strip box.
Operating Instructions
1. Preparing the Test Strip
Take one test strip from the vial. Close the vial cap immediately to protect remaining strips from moisture.
With the blood collection port facing upwards, insert the test strip into the test strip slot on the meter. The meter will display a blood drop symbol, indicating it is ready for blood collection.
2. Blood Collection
Clean and dry your hands thoroughly before blood collection.
Use the lancing device to obtain a blood sample from your fingertip. It is recommended to use the sides of the fingers for less pain.
Gently press around the fingertip to increase the amount of blood drawn.
Remove a capillary tube. Let the tip of the tube touch the blood droplet to draw blood naturally. Do not squeeze the end of the tube or block the air vent. The total blood volume should be approximately 40 microliters (up to the black graduation line).
3. Applying Blood Sample and Reading Results
Image Description: A quick start guide showing 6 steps: Time Setting, Code Card, Insert Test Strip, Draw Blood Sample, Add Blood Drop, and Read the Result.
- Add the collected blood sample into the test sample well of the inserted test strip at once.
- The meter will begin analysis. Results for Total Cholesterol (TC), Triglycerides (TG), High-Density Lipoprotein (HDL), Low-Density Lipoprotein (LDL), and TC/HDL ratio will be available in approximately 2 minutes.
4. Viewing Stored Data
After removing the test strip, the instrument will automatically store the measurement results (up to 300 recent results with time and date stamps) and turn off.
You can press the "M" key to view recent test results.
Product Features
- Rapid Test: Achieve highly accurate cholesterol results in just 2 minutes with a small sample size.
- 5 Results from 1 Test: With a single small sample, obtain comprehensive cholesterol results, including Total Cholesterol, Triglycerides, HDL, LDL, and the TC/HDL ratio.
- Ease of Use: The most user-friendly cholesterol testing device on the market, requiring only a minimal sample (35–40 µL).
- Data Storage: The URIT Cholesterol Test Meter features an integrated storage capacity for up to 300 of the most recent test results, complete with time and date stamps, allowing users to easily track their health trends.
Specifications
| Feature | Detail |
|---|---|
| Brand | URIT |
| Model | PFS-30A |
| Package Dimensions | 1.97 x 1.57 x 1.18 inches; 10.58 ounces |
| Number of Pieces | 1 (meter) |
| Special Feature | Easy to Use |
| Specific Uses For Product | Hemoglobin Test (Note: Product title indicates Lipid/Cholesterol, this might be a data discrepancy) |
Maintenance and Disposal
Clean the meter with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
Store the meter and test strips in a cool, dry place away from direct sunlight and moisture.
Dispose of used lancets and test strips in a sharps container or according to local regulations for biohazardous waste.
Troubleshooting
If the meter displays an error code, refer to the full user manual for specific troubleshooting steps. Ensure proper blood sample volume and correct code card matching.
If the screen turns off due to inactivity, press the power button and reinsert the test strip to wake the meter.
Warranty and Support
For warranty information or technical support, please refer to the contact details provided in the product packaging or contact URIT Official customer service.
