Introduction
The Qraxond Interactive Cat Toy Model C02 is designed to provide engaging play for indoor cats. It features dual motors for random rotation of a fluttering butterfly and a plush tail, simulating a hide-and-seek game. The toy is rechargeable and includes touch-sensitive activation with adjustable speed modes.
Figure 1: Overview of the Qraxond Interactive Cat Toy with multiple play modes.
Safety Information
- This product is intended for pet use only. Keep out of reach of children.
- Inspect the toy regularly for damage. Discontinue use if any part becomes loose or broken to prevent choking hazards.
- Ensure the toy is placed on a flat, stable surface during operation.
- Use only the provided USB cable for charging. Do not use a power adapter exceeding 5V.
- Do not immerse the main unit in water. The cover cloth is washable, but the electronic components are not.
Package Contents
Verify that all items are present in the package:
- Interactive hide-and-seek cat toy main unit ×1
- Plush tail wand attachment ×1
- USB charging cable ×1
- Instruction manual ×1
Setup
Assembly
- Install the Plush Tail Wand: Locate the opening on the cover cloth. Insert the plush tail wand firmly into the plastic protrusion until you hear a "click." This ensures it is securely locked in place.
- Install the Fluttering Butterfly: Align and insert the steel wire base of the butterfly accessory into the main unit's center groove at the correct angle.
Figure 2: Step-by-step guide for installing the plush tail wand and fluttering butterfly.
Operating Instructions
Power On/Off and Mode Selection
The main unit features two buttons: one for the butterfly (left) and one for the plush tail (right).
- To Activate: Press either the left or right silicone switch to start the toy.
- Speed Modes: Each button allows you to cycle through three speed settings:
- Steady (Blue Light): For calm cats.
- Active (Purple Light): For high-energy cats.
- Random (Yellow Light): For active cats, offering varied play.
- Touch-Sensitive Activation: The toy features smart touch-sensor technology. Simply tap the device to initiate a 5-minute automatic play session. After this, it enters a 1.5-hour rest period (all indicator lights flash). Following the rest period, it moves to standby mode (purple light flashes every 5 seconds). Tap again to reactivate. This cycle prevents overstimulation and conserves power.
- Bird Chirping Sound: The built-in speaker emits realistic bird chirps to attract your cat's attention. This feature is integrated into the play modes.
Figure 3: Control panel with mode indicators.
Figure 4: Explanation of the touch-sensing auto-on feature and play cycle.
Charging the Battery
The toy is equipped with a built-in 1200mAh rechargeable battery.
- Locate the Charging Port: Gently lift the silicone cover located on the power button area of the main unit. This will reveal the Type-C charging port.
- Connect the Charger: Insert the included USB charging cable into the Type-C port. Connect the other end to a 5V USB power adapter (not included).
- Charging Indicator: The indicator light will show charging status (e.g., red for charging, green for fully charged).
- Charging Time: A full charge takes approximately 2.5 hours and provides up to 3 days of playtime, depending on usage.
Figure 5: Steps for charging the toy.
Maintenance
Cleaning the Cover Cloth
The cover cloth is washable for hygiene. To clean, you must first disassemble the toy:
- Remove Accessories: First, pull out the plush tail wand. Then, carefully pull out the steel wire butterfly accessory from the main unit.
- Unscrew Fixed Rings (Front): Unscrew the circular plastic piece (fixed ring) on the main unit's front counter-clockwise. Remove the cover cloth from the top opening.
- Unscrew Fixed Rings (Back): Flip the main unit over. Unscrew the other fixed ring on the back.
- Separate Main Unit and Cover: Disengage the center of the cover cloth from the three stoppers on the main unit and remove the cover cloth.
- Wash and Dry: The cover cloth can be hand-washed or machine-washed on a gentle cycle. Allow it to air dry completely before reassembly.
- Reassembly: Follow the disassembly steps in reverse to reassemble the toy.
Figure 6: Disassembly process for cleaning the cover.
Troubleshooting
| Problem | Solution |
|---|---|
| Plush tail wand keeps falling out. | Ensure the plush tail wand is pushed firmly into the plastic protrusion until you hear a "click" to secure it. |
| Toy does not turn on or respond. | Check if the battery is charged. Connect the USB cable and charge for 2.5 hours. Ensure the silicone cover over the charging port is properly closed after charging. |
| Toy stops playing frequently. | The toy has a built-in 5-minute play session followed by a 1.5-hour rest period to prevent overstimulation and save power. Tap the device to reactivate it after the rest period. |
Specifications
- Model Number: C02
- Brand: Qraxond
- Product Dimensions: 14 x 7.8 x 14.2 cm
- Item Weight: 336 g
- Material: Plush + Plastic
- Battery: 1200mAh Nonstandard Battery (included)
- Charging Time: Approximately 2.5 hours
- Playtime per Charge: Up to 3 days (depending on usage)
- Indoor/Outdoor Usage: Indoor
Warranty and Support
Warranty Information
This Qraxond product comes with a 1-Year Warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use. It does not cover damage caused by misuse, accidents, or unauthorized modifications.
Customer Support
For any quality issues, technical assistance, or warranty claims, please contact Qraxond customer support via email. We are committed to your complete satisfaction.
Manufacturer Contact Information:
Business Name: Shanghai Qiping Technology Co., Ltd.
Business Address: Building 2, No. 181 Songyu Road, Tinglin Town (Jingliang Economic Zone), Jinshan District, Shanghai City, Shanghai, Postal Code: 201505, China