Evmore 2 Seater 4WD Electric Ride-On Car for Kids

1. Important Safety Information

Please read and understand all instructions before operating the Evmore 2 Seater 4WD Electric Ride-On Car. Keep this manual for future reference.

• This product is certified to ASTM and CPSIA standards.
• Each seat is equipped with an independent three-point safety harness. Always ensure children are securely fastened.
• For younger children (ages 2-3), parental supervision and use of the 2.4G remote control are recommended to ensure safety.
• Recommended age range for independent driving is 3-8 years.
• Maximum weight capacity is 110 pounds.
• Do not dispose of batteries in fire or water.
• Please recycle used batteries responsibly.

2. Package Contents

Ensure all components are present before beginning assembly:

• Main Vehicle Body
• Wheels (4)
• Steering Wheel
• Seats (2) with Safety Harnesses
• Front Bumper
• Roll Bar with Lights
• 12V Battery (pre-installed)
• 2.4G Remote Control
• Charger
• Assembly Tools (wrenches, screwdriver, screws)

3. Setup and Assembly

Follow these steps to assemble your Evmore Electric Ride-On Car. For a visual guide, please refer to the assembly video below.

1. Prepare the Vehicle: Carefully remove the vehicle body and all components from the packaging. Place the vehicle upside down on a soft, clean surface.
2. Install Rear Axle and Motors: Attach the rear axle and connect the motor wires as shown in the video. Secure with provided screws and washers.
3. Attach Wheels: Slide each wheel onto its respective axle. Secure with washers and nuts, then attach the hubcaps.
4. Install Front Bumper: Position the front bumper and secure it with the provided screws.
5. Connect Steering Wheel: Carefully feed the steering wheel wires through the steering column. Connect the wires to the corresponding connectors inside the dashboard. Secure the steering wheel to the column with the provided screw.
6. Connect Battery: Locate the battery compartment (usually under the seat). Connect the red battery terminal to the corresponding red wire.
7. Install Seats: Place the seats into the vehicle body and secure them with screws. Ensure the safety harnesses are accessible.
8. Attach Roll Bar: Connect the roll bar to the designated slots at the rear of the vehicle. Connect the light wires if applicable.

4. Operating Instructions

Your Evmore Electric Ride-On Car offers both manual and remote control operation for versatile play.

4.1 Manual Control

Children can operate the vehicle independently using the foot pedal and steering wheel.

• Start/Stop: Press the power button to turn the vehicle on. Use the forward/back switch to select direction. Press the foot pedal to move. Release the pedal to brake.
• Steering: Use the steering wheel to control direction.
• Speed Settings: The vehicle features multiple speed settings (1.2-1.9-3.1mph) which can be adjusted via the dashboard controls.

Image: This image illustrates both manual control by a child and remote control by a parent, highlighting the dual operating modes.

4.2 Remote Control Mode

Parents can use the 2.4G remote control to operate the vehicle, especially for younger children or for safety intervention.

• Pairing: Refer to the remote control's specific instructions for pairing with the vehicle.
• Controls: The remote allows control over forward/reverse movement, steering, and speed selection (3 speed settings).
• Safety Override: The remote control typically has priority over manual controls for immediate stopping or direction changes.

4.3 Entertainment Features

• LED Lights: Turn on the dazzling LED headlights using the dedicated switch on the dashboard.
• Music System: The vehicle includes built-in music. Connect your mobile device via Bluetooth or use the USB music mode to play your child's favorite tunes and stories.
• Horn & Engine Sounds: Activate the horn and realistic engine sounds for an authentic driving experience.

Image: This image highlights the durable anti-slip wheels and the vehicle's capability to traverse multiple terrains, including grass, asphalt, brick, and boardwalk.

5. Maintenance

Regular maintenance ensures the longevity and safe operation of your ride-on car.

• Charging: Charge the 12V 7Ah battery fully before first use (typically 8-12 hours). Do not overcharge.
• Battery Care: Store the vehicle with a fully charged battery. Recharge at least once a month during periods of non-use.
• Cleaning: Wipe the vehicle with a damp cloth. Do not use harsh chemicals or abrasive cleaners. Avoid spraying water directly onto electrical components.
• Inspection: Periodically check all screws, nuts, and connections to ensure they are tight. Inspect wheels and tires for wear or damage.
• Battery Disposal: Always recycle used batteries according to local regulations.

6. Troubleshooting

If you encounter any issues, please refer to the following common troubleshooting tips:

• Vehicle Not Moving: Check battery connections. Ensure the battery is charged. Verify the power switch is on and the forward/back switch is in the correct position.
• Remote Control Not Working: Ensure the remote control has fresh batteries and is properly paired with the vehicle.
• Low Power/Slow Speed: The battery may need charging. Check for excessive load (over 110 lbs).
• Unusual Noises: Inspect wheels and axles for obstructions or loose parts.
• Lights/Music Not Working: Check all electrical connections. Ensure the vehicle is powered on.

If problems persist, please contact customer support.

7. Specifications

Image: The main product image displaying the blue Evmore 2 Seater Ride-On Car, along with key dimensions and safety certifications (ASTM, CE).

8. Warranty and Support

Evmore products are designed for quality and durability. For warranty information, technical support, or replacement parts, please refer to the contact information provided at the point of purchase or visit the official Evmore website.

Please retain your proof of purchase for any warranty claims.