Introduction
This manual provides detailed instructions for the assembly, operation, and maintenance of your PHOENIX GRAVITY 0.26 Gallon 304 Grade Stainless Steel Gravity Water Filter. Please read this manual thoroughly before using the product to ensure proper function and longevity.
Product Overview and Components
The PHOENIX GRAVITY water filter system is designed to provide purified water using gravity. It features a durable 304-grade stainless steel construction and includes a smart carbon filter for effective contaminant reduction.
Image: The complete PHOENIX GRAVITY 0.26 Gallon Stainless Steel Gravity Water Filter system, including the upper and lower chambers, a carbon filter, and a stainless steel water bottle.
The system consists of the following main components:
- Upper Chamber: Holds unfiltered water.
- Lower Chamber: Collects filtered water.
- Smart Carbon Filter(s): Filters contaminants from water.
- Spigot: For dispensing filtered water.
- Lid: Covers the upper chamber.
Image: A detailed view of the PHOENIX GRAVITY filter system, highlighting its stainless steel construction and the internal filter components.
Setup Instructions
- Unpack Components: Carefully remove all parts from the packaging. Verify that all components listed in the "Product Overview" section are present.
- Wash Components: Wash both stainless steel chambers, the lid, and the spigot with warm, soapy water. Rinse thoroughly to remove any manufacturing residues.
- Prepare Filters:
- Submerge the carbon filter(s) in water for at least 15 minutes to allow them to fully saturate.
- While submerged, gently scrub the exterior of the filters to remove any loose carbon dust.
- Flush each filter under running water for 1-2 minutes to remove any remaining carbon fines.
- Install Spigot:
- Insert the spigot stem through the hole in the lower chamber.
- Place a washer on the inside of the chamber, then secure with the nut. Hand-tighten only to prevent damage. Ensure a snug fit to prevent leaks.
- Install Filters:
- Place the upper chamber on top of the lower chamber.
- Insert the threaded stem of the prepared carbon filter(s) through the holes in the bottom of the upper chamber.
- Secure each filter with a wing nut from inside the upper chamber. Hand-tighten only.
- Initial Flush: Fill the upper chamber with water. Allow the water to filter through and discard the first two full batches of filtered water. This primes the filters and removes any residual carbon dust.
Operating Instructions
Using your PHOENIX GRAVITY water filter is a simple process:
- Fill the Upper Chamber: Pour untreated water into the upper chamber. Do not fill above the top of the filters.
- Allow Filtration: Gravity will draw the water through the filters into the lower chamber. The filtration rate is approximately 2.25 gallons per hour.
- Dispense Water: Once water has collected in the lower chamber, use the spigot to dispense purified water.
Image: A visual representation of the water filtration process, demonstrating how water flows from the upper chamber through the filters to the lower chamber.
Maintenance
Regular maintenance ensures optimal performance and extends the life of your filter system.
Cleaning the System
- Periodically clean the stainless steel chambers and lid with warm, soapy water. Rinse thoroughly.
- For stubborn stains, a mild stainless steel cleaner can be used, followed by a thorough rinse.
Filter Replacement
The smart carbon filters have a lifespan of up to 2642 gallons or approximately 12 months, whichever comes first. Replace filters when you notice a decrease in filtration rate or a change in water taste/odor.
- Empty both chambers and remove the upper chamber.
- Unscrew the wing nuts from the bottom of the old filters and remove them.
- Dispose of old filters responsibly.
- Install new, pre-primed filters following steps 3 and 5 of the "Setup Instructions".
- Perform an initial flush with the new filters as described in step 6 of the "Setup Instructions".
Image: A close-up of the smart carbon filter, highlighting its natural coconut shell activated carbon composition and NSF certification. Note: The filter lifespan for this model is up to 2642 gallons or 12 months.
Image: An illustration detailing the two-stage filtration process of the carbon filter, demonstrating its effectiveness against various contaminants including chlorine, heavy metals, and microplastics.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Slow Filtration Rate | Filters are clogged or not properly primed. | Remove filters and re-prime them by scrubbing and flushing. If issue persists, filters may need replacement. |
| Water Leaks from Spigot | Spigot not tightened correctly or missing washer. | Ensure spigot nuts and washers are correctly installed and hand-tightened. If necessary, disassemble and reassemble the spigot, ensuring all washers are in place. |
| Unpleasant Taste/Odor | Filters are exhausted or not properly flushed. | Perform an initial flush (discard first two batches). If taste/odor persists, filters may need replacement. |
| Water Leaks between Chambers | Upper chamber not seated correctly on lower chamber. | Ensure the upper chamber is properly aligned and seated firmly on the lower chamber. |
Specifications
| Feature | Detail |
|---|---|
| Model Number | P1P5C1-US |
| Capacity | 0.26 Gallons (approximately 1 liter) |
| Material | 304 Grade Stainless Steel |
| Filter Type | Smart Carbon Filter (NSF Certified) |
| Filter Lifespan | Up to 2642 Gallons or 12 Months |
| Filtration Rate | Up to 2.25 Gallons/Hour |
| Product Dimensions | 7.4"L x 7.4"W x 11.8"H (18.8 cm L x 18.8 cm W x 30 cm H) |
| Installation Type | Countertop |
| Power Source | No Power Required (Gravity Fed) |
| Supported Water TDS Level Maximum | 500 PPM |
Image: The PHOENIX GRAVITY portable water filter, illustrating its compact dimensions for easy placement and transport.
Warranty and Support
PHOENIX GRAVITY products are designed for durability and performance. This product comes with a 10-year warranty on the stainless steel components, ensuring long-term reliability.
For technical support, replacement parts, or warranty claims, please contact PHOENIX GRAVITY customer service through the retailer where the product was purchased or visit the official PHOENIX GRAVITY website.
Additional protection plans may be available for purchase separately, offering extended coverage for your product.