AINAVI 12.3-inch Android Touchscreen for Audi Q5 (2009-2017) Multimedia System

1. Introduction

Thank you for choosing the AINAVI 12.3-inch Android Touchscreen for your Audi Q5. This manual provides detailed instructions for installation, operation, and troubleshooting to ensure you get the most out of your new multimedia system. Please read this manual thoroughly before installation and use.

2. Vehicle Compatibility

This Android unit is exclusively designed for the Audi Q5 (2009-2017) with the original Audi Multimedia radio system. It is compatible with left-hand driving vehicles.

Important: Before purchasing or installing, please verify that your car has an "Audi Multimedia" CD amplifier system. This unit is NOT compatible with original "Audi Concert" or "Audi Symphony" systems.

Image: Visual guide showing compatible Audi Multimedia system and incompatible Audi Concert/Symphony/Chorus/CD Changer systems.

3. What's in the Box

Please check the package contents against the list below:

• 12.3" CarPlay Head Unit x1
• ISO Wiring Harness Cable x1
• Metal Bracket x1
• Screws x8
• Installation Frame x1
• LVDS cable x1
• 24 Hours Engineer--Customer Support (Service)

Image: All components included in the product package, such as the 12.3-inch screen, frame, wiring harness, LVDS cable, GPS antenna, 4G antenna, metal bracket, tools, and manuals.

4. Installation Guide

This section provides a general overview of the installation process. For a detailed visual guide, please refer to the official installation video below.

4.1. Pre-Installation Steps

1. Use a tool to carefully pry off the faceplate of the original car radio.
2. Disconnect the cable on the right side of the faceplate.
3. Using a T20 screwdriver, remove the four screws securing the original display.
4. Unplug the display screen connection cable. Hold the buckle and gently wiggle it left and right to disconnect.
5. Remove the passenger side panel.
6. Use an 8mm socket to remove the screw behind the passenger side panel.
7. Use a special tool to pull out the original CD player.
8. Unplug all cables connected to the back of the CD player.
9. Use an 8mm socket to remove the screws inside the storage compartment.
10. Remove the screws at the bottom of the storage compartment using an 8mm socket.
11. Unplug the storage compartment connection cable.

4.2. Wiring and Connections

12. Connect the main power cable to the adapter cable.
13. Connect the other end of the adapter cable to the new head unit.
14. Pass the main power harness from the main unit compartment into the radio compartment.
15. Pass the two USB cables and one radio cable from the main unit compartment into the passenger compartment.
16. Open the center speaker cover using a tool.
17. Unscrew the two fixing screws and unplug the speaker connection cable.
18. Pass the purple and cyan cables from the radio compartment.
19. Connect the cyan cable to the original car cable and the purple cable to the speaker.
20. Locate the specific cable and pass it from the main unit compartment into the passenger compartment.
21. Connect this cable to the corresponding cable that was just passed through.
22. Press the buckle and unplug the original car gateway plug, then plug in the adapter plug.
23. Plug the other end of the adapter cable back into the original car gateway plug.
24. Attach the GPS signal receiver and 4G antenna to the car, ensuring proper placement for optimal signal.
25. Pass their extension cables into the radio compartment.
26. Leave the USB cables outside for easy access.
27. Pass the radio cable from the hole into the storage compartment.
28. Connect the radio adapter cable.
29. Plug the other end into the side radio port.
30. Place the CD main unit cables into the storage compartment.
31. Plug in the storage compartment interface.
32. Cover the panel and use an 8mm socket to screw on the screws.
33. Cover the side panel.
34. Plug in the CD player plugs tightly and reinstall it. Note: If this CD player main unit is not plugged in tightly and installed correctly, the original car information will not be displayed.
35. Use an 8mm socket to install the top screws of the storage compartment.
36. Push the main unit into the main unit compartment.
37. Locate the "LVDS" cable and connect it.
38. Pass the five cables out of the iron cover plate.
39. Pass the power interface from the right, and the other cables from the left.
40. Screw on the four fixing screws. Note the direction of the iron cover plate: the protruding side facing outwards, and the double holes facing upwards.
41. Take out the decorative cover plate and connect the hazard light connection cable. Connect the other end to the original car's hazard light interface. If your car has an original car hazard light. If there is no original car hazard light, you do not need to connect it.
42. Pass the required cables out of the panel window.
43. Install the buckles on the panel.
44. Connect the 4G and GPS cables to the radio. The interfaces on the machine are labeled, be careful not to connect them incorrectly.
45. Connect the power cable and LVDS cable to the machine.
46. Align the limit holes and buckle down.
47. Go to the top of the radio, open the two fixing screw holes, install the fixing screws, and close the screw holes.

4.3. Installation Video Guide

Watch the official installation video for a step-by-step visual walkthrough:

5. Operating Instructions

Your AINAVI Android Touchscreen offers a wide range of features to enhance your driving experience. Here's how to use some of the key functions:

5.1. System Overview

The 12.3-inch HD QLED display (2400x900 resolution) provides an excellent visual experience. It runs on an Octa-Core processor with Android 13, 4GB RAM, and 64GB ROM for smooth performance and ample storage.

Image: Close-up of the 12.3-inch HD QLED display showcasing its high resolution and G+G technology.

5.2. Retaining Original Car Functions

The unit operates with dual systems, retaining all original car CD system functions while adding Android system capabilities. It is compatible with original radio features such as the iDrive Knob control, Bluetooth, Radio, OEM rear camera, Radar, and steering wheel controls.

Image: Displaying various original car functions like steering wheel control, original radio, CD player, amplifier system, Bluetooth, and backup camera display, all retained after installation.

5.3. Wireless CarPlay & Android Auto

Enjoy built-in Wireless CarPlay and Wired Android Auto. Connect your smartphone wirelessly via Bluetooth to access GPS navigation, make calls, send/receive messages, and listen to music, all while focusing on driving.

Image: Demonstrating Wireless CarPlay and Android Auto interfaces on the AINAVI screen, showing various compatible apps.

5.4. GPS Navigation & Offline Maps

The system supports Google Maps offline capabilities, ensuring detailed directions even in remote areas or without a cellular signal. It's your perfect travel companion.

Image: The AINAVI screen displaying a GPS navigation map with voice assistant icons, highlighting online and offline map support.

5.5. Media Playback & DSP

Play your favorite music and videos with ease. The steering wheel buttons allow you to adjust media volume and switch between tracks. Fine-tune your audio with the music's DSP (Digital Signal Processor) settings, choosing from various preset music styles or customizing your sound with the 30-band EQ.

5.6. Digital Instrument Cluster & Car Info

Keep an eye on your digital instrument cluster, displaying information like RPM, door status, and speed directly on the screen.

5.7. Multitasking with Split-Screen

Multitasking is a breeze with the split-screen display, allowing you to navigate and enjoy entertainment simultaneously.

5.8. 4G LTE & Dual Wi-Fi

With 4G LTE and versatile dual-channel Wi-Fi (supporting both 2.4GHz and 5.0GHz), this multimedia radio delivers the speed necessary for buffer-free streaming, quick browsing, and rapid app downloads.

5.9. Operating Video Guide

Watch the official operating video to see the main functions in action:

6. Maintenance

To ensure the longevity and optimal performance of your AINAVI Android Touchscreen, follow these maintenance guidelines:

• Cleaning the Screen: Use a soft, lint-free cloth specifically designed for electronics screens. Dampen the cloth slightly with water or a screen cleaner (avoid harsh chemicals) and gently wipe the screen.
• Software Updates: Periodically check for software updates to ensure you have the latest features and bug fixes. Refer to the system settings for update options.
• Cable Management: Ensure all cables are securely connected and properly routed to prevent damage or interference.
• Avoid Extreme Temperatures: Do not expose the unit to extreme heat or cold for extended periods, as this can affect performance and lifespan.

7. Troubleshooting

If you encounter any issues with your AINAVI Android Touchscreen, please refer to the following common solutions:

• Bluetooth Disconnection: If Bluetooth frequently disconnects, ensure no other devices are simultaneously connected to the Audi original Bluetooth system. Try restarting both your phone's Bluetooth and the unit's Bluetooth. If the issue persists, check for firmware updates.
• Original Car Information Not Displayed: This often occurs if the original CD player's main unit cables are not plugged in tightly or correctly during installation. Re-check all connections to the CD player.
• No Power: Verify all power connections are secure and correctly installed. Check the vehicle's fuse box for any blown fuses related to the radio or multimedia system.
• Touchscreen Unresponsive: Try restarting the unit. If the issue continues, ensure the screen is clean and free of debris.
• Poor Sound Quality: Adjust the DSP settings to optimize audio output. Ensure all audio cables are securely connected.

For persistent issues, please contact customer support.

8. Specifications

9. Warranty & Support

For customer support, installation assistance, or any inquiries regarding your AINAVI product, please contact HomeCar, the seller, directly. They are committed to providing a high standard of customer service.

• Seller: HomeCar
• Customer Service Phone: +1 (833) 858-5016
• Working Hours: 01:00 PM to 00:00 AM PST
• Email: info@ainavi.com

You can also visit the AINAVI Store on Amazon for more information and products.